- test-drb@ccmp.vtda.org - classiccmp.org

by lars＠nocrew.org

Hello, People have been earching for PDP-10 MDL for a long time. Finally, we found source code for TOPS-20 including slightly bit-rotted ITS support. It has now been fixed and is up and running in ITS. Twenex people are welcome to give it a go too. This is published with permission from Chris Reeve and Tim Anderson: http://github.com/PDP-10/muddle Next is, of course, trying to run Zork. How to do that is an entire research project of its own. Best regards, Lars Brinkhoff

8 years, 1 month

1
0
0 0

Amusing IBM test system model

by donald＠donaldwhittemore.com

Well, the ones listed now have been re-listed at least once. :-( I was just contacted by the Living Computers Museum. They emphasized they are a 501(c)(3) org. :-) I donate to the CHM. I will probably give them first shot.

8 years, 1 month

2
1
0 0

Cybernex APL-100 terminal

by turing＠shaw.ca

Does anyone in the group have access to documentation for the Cybernex APL-100 video terminal? All that I've been able to locate is a 4 page brochure for it; they were originally made in Ottawa, Ontario, Canada. Any help would be greatly appreciated.

8 years, 1 month

2
1
0 0

Digilog DLM III?

by w2hx＠w2hx.com

Hi friends. Looking for a user manual (or anything) for this data line monitor. Here is a picture: http://w2hx.com/x/Digilog/Digilog-DLM-III.jpg Thanks

8 years, 1 month

3
3
0 0

VME Bus

by david＠thecoolbears.org

I hope this qualifies as classic computing... Does anyone have the pin-out for the P2 connector on MVME processor boards? I think that the pin-out would be the same for MVME147, MVME177, MVME162, etc. and would mate with the P2 adapter board.

8 years, 1 month

2
1
0 0

ISO Sun (Fuji Electrochemical) 300-1024 power supply

by aek＠bitsavers.org

I have a x/280 server chassis that has a power supply that's acting up (DC shuts down after a few seconds) Anyone have one they can spare? Sun PN 300-1024 http://www.shrubbery.net/~heas/sun-feh-2_1/Systems/Sun4/DCPOWER_Fuji_1024_8… or has anyone seen this problem before (caps in the DC monitor circuit?)

8 years, 1 month

2
1
0 0

USB Panda Display for klh10 help

by bygg＠cafax.se

David Griffith <dave at 661.org> wrote: > I'm looking for someone who knows TOPS10 / TOPS20 well enough to figure > out for me why this test program won't compile. Once that's done, I can > complete the firmware for the USB Panda Display an its support within > klh10. I'll then make more copies of the USB Panda Display board (and > maybe overlays) for whoever wants them. A couple of observations on the following code: 1/ It is written for, and uses TOPS20 syscalls. If you intend to run this under TOPS10 change the syscalls (LITES% and DISMS%) to the equvialent TOPS10 counterparts, can be done by including these lines: SEARCH UUOSYM OPDEF LITES% [LIGHTS] OPDEF DISMS% [HIBER] 2/ The program uses the CIRC instruction, which is not present in stock DEC processors, and possibly not known to MACRO-10. You could try OPDEF CIRC [247000,,0] if that is indeed the problem. [source code trimmed down] > David Griffith --Johnny

8 years, 1 month

2
1
0 0

Multics Lives

by rtomek＠ceti.pl

Howdy, It seems to go unmentioned here, so here you are. One guy have set up a public Multics site. Access via ssh: # ~$ ssh dps8 at m.trnsz.com # The authenticity of host 'm.trnsz.com (139.162.119.37)' can't be # established. # ECDSA key fingerprint is # e7:f6:da:31:eb:a0:a5:0b:50:fc:91:96:32:e7:18:f2. # Are you sure you want to continue connecting (yes/no)? yes # Warning: Permanently added 'm.trnsz.com,139.162.119.37' (ECDSA) to the # list of k # nown hosts. # Connection from: AAA.BBB.CCC.DDD # Session starting now, Fri 20 Apr 2018 at 15:34:42 UTC. # # BAN.AI Systems Public Access Multics Service # # ? ? ??? ? ? # ?? ?? ? ? ? ????? ??? ??? ??? # ? ?? ? ? ? ? ? ? ?? ? ? ? # ? ?? ? ? ? ? ? ? ? ???? # ? ? ????? ??? ??? ?????????? ????? # # Visit https://ban.ai/multics/ to request a full user account # Guest print job output at https://ban.ai/spool/anonymous # Public anonymous login available. Type "enter Guest" to login # # # Multics MR12.6f: BAN AI Systems (Channel a.h001) # Load = 10.0 out of 300.0 units: users = 10, 04/20/18 1034.7 est Fri # enter Guest # You are protected from preemption until 10:35. # Anonymous user Guest.Guest logged in 04/20/18 1035.0 est Fri from # ASCII termin # \cal "none". # New messages in message_of_the_day: # # Welcome to the BAN AI Systems Public Access Multics Service! ... and so on, and so on ... (the '# ' comes from me, to make screen dump stand out from my own words) I have none prior experience with Multics, so it is going to be interesting. I guess. Source: AN.AI's Public Access Multics System https://lobste.rs/s/4ktahz/ban_ai_s_public_access_multics_system https://ban.ai/multics/ -- Regards, Tomasz Rola -- ** A C programmer asked whether computer had Buddha's nature. ** ** As the answer, master did "rm -rif" on the programmer's home ** ** directory. And then the C programmer became enlightened... ** ** ** ** Tomasz Rola mailto:tomasz_rola at bigfoot.com **

8 years, 1 month

4
5
0 0

USB Panda Display for klh10 help

by dave＠661.org

I couple years ago I completed the design for my USB Panda Display[1] board. This is a modernization of the original Panda Display once distributed by Spare Time Gizmos[2]. Both devices are intended to be connected to a more-or-less modern x86-class computer running the klh-10 pdp10 emulator and provide useful blinkenlights. The development of klh10 is once again active, this time on Github[3]. I created my own repo of klh10 as a means of writing support for my new Panda Display. The display seems to be recognized and used, but what it displays is meaningless. I cannot fully test it until I can get the old test program compiled and working. Once that's done, I'll add my changes to the PDP-10/klh10 repo and delete my own. Here's a video of a computer with the old Panda Display running klh10: https://www.youtube.com/watch?v=g_LcQ5apODg. The creator of that video, Jan de Rie, got the program that was used to generate that pattern from Mark Crispin, the creator of the Panda distribution of klh10. That program appears at the end of this post. I'm looking for someone who knows TOPS10 / TOPS20 well enough to figure out for me why this test program won't compile. Once that's done, I can complete the firmware for the USB Panda Display an its support within klh10. I'll then make more copies of the USB Panda Display board (and maybe overlays) for whoever wants them. TITLE HACK SEARCH MONSYM HACK: SKIPA 4,[^D4] HACK0: SOJL 4,TRAILL SETZB 1,3 HACK1: TLNE 1,777777 JRST HACK0 MOVE 2,1 CIRC 2,-^D18 SKIPN 4 SKIPA 1,3 IOR 1,3 LITES% HALT HRRZ 2,1 MOVEI 1,30 DISMS% MOVE 1,2 AOJA 1,HACK1 TRAILL: SETZ 1, TRALL0: LITES% HALT MOVE 2,1 MOVEI 1,30 DISMS% JUMPL 2,TRAILR LSHC 1,^D37 AOJA 1,TRALL0 TRAILR: MOVSI 1,400000 TRALR0: LITES% HALT MOVE 2,1 MOVEI 1,30 DISMS% MOVE 1,2 TRNE 1,1 JRST HACK ASH 1,-1 JRST TRALR0 END HACK [1] https://github.com/DavidGriffith/panda-display [2] http://sparetimegizmos.com/Hardware/Panda.htm) [3] https://github.com/PDP-10/klh10/ -- David Griffith dave at 661.org A: Because it fouls the order in which people normally read text. Q: Why is top-posting such a bad thing? A: Top-posting. Q: What is the most annoying thing in e-mail?

8 years, 1 month

1
0
0 0

TRS-80 bits

by wrm＠dW.co.za

Hi Jim and all >Hmm, I guess it does indeed depend on shipping costs, but I am looking >for a card cage for the 12, and they can be a bit tough to find. Yea, we tend to use couriers but it runs to a few hundred dollars a pop. I will send pics off-list sometime next week. W

8 years, 1 month

1
0
0 0

Andromeda SCDC Qbus controller question

by Flash688＠flying-disk.com

Douglas Taylor <dj.taylor4 at comcast.net> wrote: > I just got one of these and wanted to configure it via the 10 > pin RS232 port on the board. > Is the port a standard DLV11-J type? Yes, it is identical. I was the original beta tester on the SCDC and used it extensively. In fact, the designers called it "the Frisbie port". :-) > I have one of those D-bit DLV11-J to DB25 adapters but not > getting any response. You may need a null modem. Try swapping pins 2 and 3. I can send you an genuine Andromeda DB25 adapter if you give me a mailing address and promise to send me $10. :-) > Any info on the few jumpers on the board? They changed between the original Rev. A and final Rev. F boards. Which one do you have? I can send you a copy of the manual, complete with all my editorial comments written on it. Alan "Packrat" Frisbie

8 years, 1 month

2
1
0 0

8085 Dissasembly?

by bygg＠cafax.se

Bill Gunshannon wrote: > Many of us think that the advent of the x86 architecture is what led to > masochism. ... or masochism led to the x86 architecture. > bill --Johnny

8 years, 1 month

14
31
0 0

sugar packjets anyone ever come across em?

by tdk.knight＠gmail.com

anyone ever come across sugar packets? this came in a lot of manuals and documents that arived the other day kinda neat https://imagizer.imageshack.com/v2/800x512q90/922/T4MCLS.jpg

8 years, 1 month

6
7
0 0

RL Drive Terminators

by bill.gunshannon＠hotmail.com

I see some company selling them on eBay for $122.? Are they really worth anything like that?? I have a couple sitting around here somewhere that I don't expect to ever use again.? Just wondering if they are worth looking for to sell.? In this hobby you can always use money for new (well, old actually) toys. bill

8 years, 1 month

7
7
0 0

To be scrapped in as little as 2 months

by pete＠petelancashire.com

3 x DEC Alphas, small deskside models 5 to 6 x Sun pizza boxes one a Sparc 1 prototype 029 IBM Keypunch The day I can have a 15 cubic yard scrap metal drop box the stuff will start to be tossed in. All based on when the rains stop and the ground is hard enough I can't want much longer For those that have not seen me post this before The stuff is near (3 - 4 miles outside of) Banks Oregon USA (look it up on Google). I CAN NOT LIFT OVER 10 LBS, PERIOD. -pete

8 years, 1 month

10
34
0 0

Manual wanted for the MFE M-700 Floppy-Disk-Drive

by harten＠injectstar.de

Hi to all! I'm looking for a technical manual/schematic for the Mayflower MFE M-700 8 inch Floppy-Disk-Drive. Regards Rolf

8 years, 2 months

1
0
0 0

new disassembler vs IDA (was Re: 8085 Dissasembly?)

by spacewar＠gmail.com

On Wed, Apr 18, 2018 at 8:17 PM, Mark J. Blair via cctech < cctech at classiccmp.org> wrote: > Some of the future reverse engineering projects I have on my to-do list > involve the CDP1802 processor, which IDA presently doesn't support. When I > get to them I'll have to decide whether to use dismantler vs. learning how > to add CDP1802 support to IDA. I'm leaning towards the latter, because IDA > is so much fancier than dismantler is. I'd vote for adding it to dismantler. I had an IDA Pro license at one point, but I seem to have misplaced it, and it is too old to get me any discount on a new release. I imagine that IDA has probably improved a lot since back then, but at the time it had a pretty awful user interface. If I had an actual business need to reverse-engineer something using a processor that IDA supported, I'd certainly buy a new IDA license, but I wouldn't personally invest any time in building add-ons for expensive commercial software, when there are open source alternatives that may not be as good, but are generally good enough. For the 1802, I've used a really crude disassembler written in C. The 1802 instruction set isn't very complicated, so a disassembler for it isn't either. It's been so many years since I actually disassembled 1802 code that I'm not sure I still have the disassembler around.

8 years, 2 months

2
1
0 0

Andromeda SCDC Qbus controller question

by dj.taylor4＠comcast.net

I just got one of these and wanted to configure it via the 10 pin RS232 port on the board. Is the port a standard DLV11-J type? I have one of those D-bit DLV11-J to DB25 adapters but not getting any response. Any info on the few jumpers on the board? Doug

8 years, 2 months

1
0
0 0

what happened to the dec thing with the butterfly discs never heard back I need it for museum thanks cindy ed

by couryhouse＠aol.com

what happened?to the dec thing with the butterfly discs never heard back I need it for museum thanks?cindy ? ?ed

8 years, 2 months

1
0
0 0

old schematics books

by sales＠elecplus.com

These have now been claimed. Thanks everybody! Sean I need an address please! Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 2 months

1
0
0 0

Speed now & then

by boris＠summitclinic.com

TAhanks for that link which fits with my measurements (nowhere as detailed) of ones actual ability to do things with "modern" hardware. In the 1980's I was used to being able to measure events with 0.2 microsecond precision using a PDP-11 and my expectation was that the accuracy was only going to improve as processors got faster. I ported a program I wrote on the PDP-11 to a Commodore 64 in 1988 and was using it to measure finger tapping with a switch array to 1 msec accuracy. This was done through the simple expedient of speeding up the sample rate for the keyboard to 1 KHz and the adding in my 4 external switches as "keys". Used a 512 K Mac to get the serial data and display results. To do the same now would require custom hardware to do the timing and a USB link to a "modern" CPU or implimentation on a microprocessor When I attempted to get this same type of timing accuracy from a PC, found out that it was no longer easy to get access to interrupts as easily as before and keyboard latency was longer as now keystrokes were detected by an on board microprocessor and sent out as a series of packets for each keystroke. In DOS and W95 where one could still easily get at interrupts, then a serial port could be used to do msec timing. Once XP and beyond arrived, then the best temporal precision one can expect from a 3 GHz machine is 15 msec. I suspect the same holds for Macs and haven't tried running real time Linux as I either pull out my trusty C64 from time to time and use it for precision timing (unfortunately have only one copy of the code on casette tape so when that goes can't do this anymore) or I use various microprocessors to do the job. Have a nice microsecond precision timer that I wrote for a Propeller chip and feel much more comfortable programming for it than the latest windoze bloatware system. The Propeller has the same amount of RAM as the PDP-11's I started on, runs 20x faster/core and is fun to program. The microsecond timer is attached to a geiger counter to generate random bytes for OTP encryption. Boris Gimbarzevsky >On 29 March 2018 at 19:53, Paul Koning via >cctalk <cctalk at classiccmp.org> wrote: > > > > It would be fun to do a "generalized Moore's > Law" chart, showing not just transistor count > growth (Moore's subject) but also the many > other scaling changes of computing: disk > capacity, recording density, disk IOPS, disk > bandwidth, ditto those for tape, CPU MIPS, > memory size, memory bandwidth, network bandwidth... > >This is the most telling I've seen in a long time... > >https://danluu.com/input-lag/ > >-- >Liam Proven ? Profile: https://about.me/liamproven >Email: lproven at cix.co.uk ? Google Mail/Hangouts/Plus: lproven at gmaill.com >Twitter/Facebook/Flickr: lproven ? Skype/LinkedIn: liamproven >UK: +44 7939-087884 ? ??R (+ WhatsApp/Telegram/Signal): +420 7002 829 053

8 years, 2 months

6
6
0 0

Last call for free old manuals

by sales＠elecplus.com

I have many cases of SAMS facts schematics and other repair manuals for everything from stereos, tube TVs, ham radios, turntables, etc. Most apply to equip from the 60s and 70s or maybe a little earlier. Free to a good home or they go in the recycle bucket tomorrow. Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 2 months

1
0
0 0

8085 Dissasembly?

by jnc＠mercury.lcs.mit.edu

> From: Charles Anthony > discovered that changing the executable would change the behavior -- a > heisenbug. Ooh, love that neologism. Noel

8 years, 2 months

2
2
0 0

TRS-80 bits

by wrm＠dW.co.za

Hi all I have a TRS-80 Model 2000 B/W Graphics board and a TRS-80 Card Cage kit (upgrade model 12 to model 16B) Are either of these worth shipping from the antipodes to anyone? W

8 years, 2 months

2
1
0 0

FYI: IBM System/34 available in Boston, MA

by cclist＠sydex.com

Just noticed this post on the Vintage Computer forum. I don't know a thing about it: http://www.vcfed.org/forum/showthread.php?63253-IBM-System-34-5340 --Chuck

8 years, 2 months

1
0
0 0

Absolute OpenBSD book

by mark＠wickensonline.co.uk

This is available for the cost of postage. https://photos.app.goo.gl/OpVKxtbXqKp2VPl52 Mark.

8 years, 2 months

1
0
0 0

Help on a 1998 Award BIOS chip

by curiousmarc3＠gmail.com

After battling for days with a Dolch 65 that developed the two-tone beep-of-death on boot, I finally found that it's just my BIOS ROM that has gone bad. The BIOS happens to be an Award BIOS, says "Award 1998 PCI/PNP 686" on the chip. It's a square chip with pins on the side. Photo here: https://drive.google.com/open?id=1OtZ1AU0Hac8RlzTgbgCY4z_qcMlGWXu1 So I thought I might just ask. Anyone has a dead Dolch 65 motherboard from which I could steal a BIOS chip. The board is actually an Advantech CI6BM-B1 industrial single board computer. Or alternately, can someone identify what kind of ROM or EEPROM that likely is, and provide advice on how to read the data from a good chip (I have another good chip in another Dolch, that's how I found out what my problem was), and program a similar chip. Marc

8 years, 2 months

5
9
0 0

8085 Dissasembly?

by w2hx＠w2hx.com

Hi friends. I have a 1990's vintage commercial radio system that uses an 80C85A CPU. I am looking to hopefully modify the firmware to make some small changes in its behavior. The firmware is contained in two EPROMS. Can anyone recommend a decent disassembler to use with this? Preferably something that ran in windows 10 or windows 7? A dos box would be fine too. Also, I looked through the dumped contents of the EPROM. In the past I have seen EPROM ascii dumps where most is unintelligible to the naked eye but typically text messages give to the users during interaction with the program are human readable. In this case, the ASCII dump shows only other HEX data. I believe I read that there is a HEX format and that I might need to convert from HEX to BIN before disassembling. Of course, an ideal tool would do both if anyone knows such a thing. I am not familiar with 8085 stuff but any insight would be appreciated. Lastly, I wonder if there might be some kind of checksum check to prevent tampering. Is there a common way this is handled in 8085 world? Or is it entirely programmer dependent? Thanks for your time Eugene W2HX?

8 years, 2 months

9
10
0 0

Kaypro II keyboard fault / keyswitches wanted

by jules.richardson99＠gmail.com

Hey all, I snagged a Kaypro II a short while ago which I finally got around to looking at. After some minor TLC to the drives, it's booting. However, the keyboard appears unresponsive. Pressing keys (with the exception of caps-lock, the two shifts, and ctrl) results in a buzz/click >from within the keyboard - if I'm interpreting the schematics right, the click is actually driven by the system in response to a keypress, which suggests that my keyswitches are OK (I believe these use a foam disc approach, which are prone to deterioration) and that keyboard data is being received OK (at least on some low level). Any suggestions for possible things to investigate? It doesn't feel like a memory fault, given that it's using 64kx1 ICs and booting as far as a prompt, but I suppose it's possible. On the back of this, I'm in need of three keyswitches, if anyone happens to have a parts machine and would be willing to sell any. A student of the machine's previous owner dropped the keyboard years ago and broke three of the keys off. I have the keycaps, but the switch stems are broken and it would probably be easier to replace the entire stem portions rather than attempting to glue things back together. cheers Jules

8 years, 2 months

3
3
0 0

Big old Telex terminal

by sales＠elecplus.com

https://www.recycledgoods.com/telex-277d-terminal-with-95146r011-keyboard-ib m-model-2-compatible/ Not affiliated with seller, etc. Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 2 months

1
0
0 0

One wafer-thin mint (VAX 4000-200 for sale)

by billdegnan＠gmail.com

The VAX 4000-200 I exhibited two years ago at VCF East is up for sale: Restoration Notes: http://www.vintagecomputer.net/browse_thread.cfm?id=608 I don't need it as much anymore now that it's pretty much a completed project. It's very upgrade-able though if you have the desire to boost performance and ports, etc. The provenance of this machine, I believe, was as part of WVLink a West Virginia email/gopher/USNET type ISP server in the early-mid 1990's. I have it set up for telnet communications if interested. Contact me via http://www.vintagecomputer.net/contact.cfm Bill

8 years, 2 months

1
0
0 0

AlphaServer 300 4/266

by mark＠wickensonline.co.uk

Good condition AlphaServer 300, always been stored in dry conditions. Photos: https://photos.app.goo.gl/5N66yIlEUCYkuh012 It has a TGA based DEC graphics card that will do 1280x1024 24 bit (it's a ZLXp-E2 PBXGA-BA) - manual included. Ultrawide 16-bit SCSI card Brand new Seagate Cheetah 15K.4 36.7GB,Internal,15000RPM,3.5" (ST336754LW) HDD Ultraplex SCSI CDROM drive. Running OpenVMS Alpha 8.3 with CDE. Can also run tru64 5.x. All working as it should be. Very quiet system. Can provide copies of media if required. ?175 + postage at cost. I can supply an LK461 keyboard and mouse for an additional ?25.

8 years, 2 months

1
0
0 0

Datatronics battery powered 2400P modem

by mark＠wickensonline.co.uk

I have one of these, see the photos: https://photos.app.goo.gl/CnLnSKTCzHETzpOo1 It was bought new by myself a few years back. It can run off a PP9 battery. ?10 shipped in the UK if anyone is interested. Regards, Mark.

8 years, 2 months

1
0
0 0

Scanned paperback book "RSX A User's Guide"

by mark＠matlockfamily.com

I recently decided to make scan a paperback book that I happen to have two copies of. It is "RSX A Guide for Users by John Pieper? published in 1987 by DEC. I have not seen a copy of it in any of the online sources like bit savers. For anyone just starting out with RSX it is a nice general read that also covers some system topics like backups, etc. similar to the paper back VAX/VMS user and system manager books. I?d like to make it available online but wasn?t sure how to submit it. It is about 38 MB in size so bigger than an email (at my email). Since I didn?t have an industrial book shear to remove the binding, I used a belt sander to remove enough go the binding to pull the pages free easily and then used a paper cutter to trim the pages a bit to remove any last traces of glue that would have jammed the scanner. The book is about 360 pages. Thanks, Mark Matlock

8 years, 2 months

6
5
0 0

Online ticketing is open for VCF East

by cctalk＠snarc.net

http://vcfed.org/wp/festivals/vintage-computer-festival-east/tickets/ Note: Your paypal email confirmation is your ticket. A record of your purchase will be at the door when you arrive at VCF East. ________________________________ Evan Koblentz, director Vintage Computer Federation a 501(c)3 educational non-profit evan at vcfed.org (646) 546-9999 www.vcfed.org facebook.com/vcfederation twitter.com/vcfederation

8 years, 2 months

1
0
0 0

Jobs, McGowan and Olsen

by dm561＠torfree.net

An interesting 3 hours on PBS last night: - 'Steve Jobs - One Last Thing': No description necessary. - 'Long Distance Warrior': McGowan/MCI's David & Goliath battle with AT&T and disastrous merger with Worldcom. - 'Digital Man/Digital World': Ken Olsen/DEC's growth and ultimate decline. (No doubt everyone here except myself had already seen this one ;-) Interesting comparison of the different styles and personalities of three men who profoundly influenced the tech world of today and their companies. Thoroughly enjoyed it. m

8 years, 2 months

3
2
0 0

8085 Dissasembly?

by Richard.Sheppard＠telus.com

> Lastly, I wonder if there might be some kind of checksum check to prevent tampering. Is there a common way this is handled in 8085 world? Or is it entirely programmer dependent? One approach that <may> be doable for you is if you have a good ROM with a known checksum, make your changes then calculate the difference between the new and the original checksum and make another change somewhere innocuous to bring the checksum back to the original value. "Innocuous" may be the trick - perhaps some text string you don't care about, copyright notice etc. or maybe there is an empty area in the EPROM you could stick a byte. Richard Sheppard

8 years, 2 months

2
1
0 0

8085 Dissasembly?

by blstuart＠bellsouth.net

On Tue, 4/17/18, Eric Smith via cctalk <cctalk at classiccmp.org> wrote: > On Mon, Apr 16, 2018 at 7:29 PM, Chuck Guzis via cctalk <cctalk at classiccmp.org> wrote: >> Disassembly is never lots of fun, > > Some of us might disagree. > But then, some of us might be masochists. I was just thinking the same thing. This whole discussion has taken me back to fond memories of writing a 68000 disassembler in AWK (long story). BLS

8 years, 2 months

2
1
0 0

LCM 8/e System Photo makes ZDNet

by jnc＠mercury.lcs.mit.edu

> From: Paul Birkel > the blinky-lights controller panel top-dead-center :->. Yeah, that's a TC08. I actually have one of those inlays, it's the only original inlay I have. It was the model for the large run of blank inlays (black backing with the holes on the back, but nothing on the front) I just had made. At the moment, it's sitting in my indicator panel stand with little bits of tape stuck to it: http://ana-3.lcs.mit.edu/~jnc/tech/QSIC/jpg/PanelMounting.jpg http://ana-3.lcs.mit.edu/~jnc/tech/QSIC/jpg/DasBlinken2F.jpg so it can be an inlay for the RKV12. If anyone needs a TC08 inlay, I'd be happy to trade it for any other inlay (as long as I have one original for engineering purposes). Sigh, need to get back to the inlays and take the next step with them! Dave B and I got derailed trying to find/fix a flaky on the QSIC - on my prototype, it would occasionally get NXM's running the RK random exerciser I wrote. I was trying to figure out what the problem was, and I got tired of the prototype sticking out in my way: http://ana-3.lcs.mit.edu/~jnc/tech/jpg/tmp/JNCQSIC.jpg (with the FPGA daughter-board on top, even with short cables, it has to be on an extender), so I rotated the QBUS chassis 90 degrees so the QSIC was on top, and took the opportunity to re-order the boards. Bad mistake! Now the problem has gone away and I can't re-create it! Noel

8 years, 2 months

2
1
0 0

8085 Dissasembly?

by jnc＠mercury.lcs.mit.edu

> From: Eric Smith > But then, some of us might be masochists. I think pretty much by definition if you're into vintage computers, you have to be a masochist... :-) Noel

8 years, 2 months

3
2
0 0

LCM 8/e System Photo makes ZDNet

by pbirkel＠gmail.com

https://www.zdnet.com/article/from-paper-tape-to-the-altair-8800-the-story-o f-my-first-computers/ Noel will appreciate the blinky-lights controller panel top-dead-center :->. paul

8 years, 2 months

2
1
0 0

Looking for 3B2 "NI" source code

by web＠loomcom.com

Hi folks, I know this is a wild long shot, but just in case... Does anybody have a copy of the source code for the NI Ethernet driver for the AT&T 3B2? AT&T distributed it, but I have never seen a copy in the wild. The package name was "nisrc", if that helps. If I can't find it, I'll have to reverse engineer the binary. Won't that be fun! -Seth -- Seth Morabito web at loomcom.com

8 years, 2 months

1
0
0 0

motorola's chip page

by dave＠661.org

Does anyone know where Motorola's current production chips are described? http://www.motorola.com/General/prodport.html only partially works and search is entirely broken because http://search.motorola.com no longer exists. -- David Griffith dave at 661.org A: Because it fouls the order in which people normally read text. Q: Why is top-posting such a bad thing? A: Top-posting. Q: What is the most annoying thing in e-mail?

8 years, 2 months

2
1
0 0

CMOS for NMOS

by dave＠661.org

I'm pondering upgrading the CPU of a Pacccomm Tiny-2 Mk2 radio packet controller from a 6Mhz Z80 processor and SIO to 10Mhz parts. My problem is that the parts already in it appear to be NMOS. The family is still being made by Zilog, but for 10Mhz parts, CMOS is all they have. Can I just drop in CMOS, change out the crystal/oscillator and have things work as expected? Here's what are fitted to my TNC. Z84C00BB6 Z80BCPU 29125 Z8440BB1 Z80BSIO-O 29014 -- David Griffith dave at 661.org A: Because it fouls the order in which people normally read text. Q: Why is top-posting such a bad thing? A: Top-posting. Q: What is the most annoying thing in e-mail?

8 years, 2 months

4
5
0 0

Speed now & then

by c.murray.mccullough＠gmail.com

I?m not trying to date myself but have things truly sped up? In 1970?s Toronto I had a classic computer, sorry can?t recall what it was, connected to a 300 baud modem; by early 80?s had ?zoomed? to 9600 baud. Oh, my! [ A typical file size to download was probably 1 MB. ] Speed indeed! Yet now, here in rural Ontario, Canada, I?m at 5MB/s. Yikes! (Friends in Toronto are at 50MB/s.) We can do the math but content, particularly multimedia, has swollen in size.[ 1 GB is not unheard of. ] Were classic computing days that much slower? Happy computing. Murray -:) <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_cam…> Virus-free. www.avg.com <http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_cam…> <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>

8 years, 2 months

24
66
0 0

To be scrapped in as little as 2 months

by jnc＠mercury.lcs.mit.edu

> From: Ed Sharpe > wish this was closer! Two words: "ROAD TRIP!!!" :-) (I did Virginia<->Wisconsin to save an -11/84... That was a hike!) Noel

8 years, 2 months

1
0
0 0

Tektronix 405 diagnostic Rom Pack copies available.

by jos.dreesen＠greenmail.ch

As mentioned before , i made a functional copy of the Tektronix 4052 Diagnostic Rom Pack . PCB's are back, units do work ( minus a small issue with the wrong orientation of the LED's ) Go to ftp://ftp.dreesen.ch/TEK_DRP ?and find my dokumentation DiagPack_Manual.pdf , decide if this is what you want, and order ( or not...) Also please read the original TEK doku TEK4052_4054_Diagnostic_Rom_Pack.pdf in order to understand what this unit can and cannot do. Prices, in short : PCB only 20 Euro/25 USD, populated and tested 60/75, add 20/25 for a fitting 3D printed casing. And do feel free to construct your own with the data from my FTP site. This pack should also work on the 4054, but since I do not have such a machine this feature is untested. Jos, now wondering whether I will ever sell the 20 PCB's I have...

8 years, 2 months

1
0
0 0

Stuff in my desk, utterly forgotten

by cclist＠sydex.com

I've found a couple more documents lurking in my desk that I've completely forgotten about. The first is a UniSoft Uniplus+ System V User Guide. Circa 1984. Basically a SysV Unix user's guide. I have no idea what platform this was intended for, as it's pretty much a generic document. A couple hundred pages. The second is a sales kit for CMS Enhancements. Nice slick brochures for PC, Apple and Sun. No technical documentation, per se--just something you'd pass out at a trade show (which is probably where I got it). Circa 1990. Includes the brochure for the CMS 386 PC. It'll all fit in a USPS PM envelope, I'm guessing. I want postage only. --Chuck

8 years, 2 months

1
0
0 0

DEC DS-32 and IBM Series 1

by djg＠pdp8online.com

Someone in Barnet, North London, post code is EN5 1RJ has two DEC DS-32 drives and IBM Series/1 computer and some drives. Last wording was Sale or swap. You may contact them at stuff at pdp8online.com.

8 years, 2 months

1
0
0 0

Speed now & then (Space and time?)

by bygg＠cafax.se

Ethan Dicks <ethan.dicks at gmail.com> wrote: > There are times when video instruction makes sense - describing, for > example, a chemical reaction that produces major visible change in a > few moments is better to watch than to try to describe. The vast > majority of stuff? Teaching programming? I don't want to watch 2 > hours of someone editing text... give me words and perhaps a > screenshot or two if there's something too complicated to simply write > about. How about language courses on audio cassettes? For instance a course on Macro-10, over several of them? Yes, it does (or at least did) exist. > -ethan --Johnny

8 years, 2 months

2
1
0 0

Nice Video on the Hershey Fonts

by tshoppa＠wmata.com

Very nice presentation by Frank Griesshammer on the subject of the Hershey Fonts: https://vimeo.com/153653610 He does a superb job explaining how a font invented in 1967 by a mathematical physicist at a US Weapons Lab became essential for the last 40 years of technical writing. And is also an interesting font for actual font designers today :-) Tim N3QE [https://www.bing.com/th?id=OVP.0QZVssVrJ4Ynm3h5opaOeAEsCo&pid=Api]<https://vimeo.com/153653610> Frank Grie?hammer ? The Hershey Fonts<https://vimeo.com/153653610> vimeo.com Recorded during TypeCon2015: Condensed in Denver, Colorado In 1967, Dr. A.V. Hershey was working at the U.S. Naval Weapons Laboratory in Virginia; on some of the ...

8 years, 2 months

1
0
0 0

Unix-PC

by bill.gunshannon＠hotmail.com

Well, I don't know what happened to everybody who wanted it but that Unix-PC is still sitting here and it needs to go.? One more offer before I scrap it.? Needs to be someone who can pick it up real soon. bill

8 years, 2 months

6
7
0 0

Amusing IBM test system model

by aek＠bitsavers.org

https://www.ebay.com/itm/132578314834 it appears IBM built a test system for NASA with an HP 1000 and 7900 disk in it

8 years, 2 months

1
0
0 0

Toshiba Laptop needing new home

by mtapley＠swri.edu

All, in San Antonio (Texas), I have a Toshiba Satellite 2065CDS/4.3 laptop, Model number PRS206U-A, whose owner wants to give or throw it away (preferred give). It has a 16-bit ethernet card including dongle and driver floppy, annoying eraser-head cursor control with replacement eraser heads, USB port, 3.5? floppy, CD drive. Starts up to Toshiba screen and shows 160 MBytes of RAM. I watched it boot to Win98 once and fail to boot many times. I think the owner had it dual-booting to Linux as well, but he is having the disk wiped to make sure no personal information goes with it. The battery kept it running for only about 15 seconds on power-disconnect after being plugged in (running) for an hour or two, so probably not much battery life available. I think the freshly-cleaned hard drive has ~ 4 GB of space, don?t know for sure about that. Let me know if you are interested; I?ll forward inquiries to the owner as I get them. - Mark 210-522-6025 office 210-379-4635 cell

8 years, 2 months

1
0
0 0

5.25- inch alignment disk needed

by spacewar＠gmail.com

I find myself in need of a 5.25-inch alignment disk. A few years ago someone mentioned a source for those, but I can't seem to find it. Is there still a source, or does anyone have one they'd be willing to sell? I could use an 8-inch alignment disk also, but don't need that as urgently.

8 years, 2 months

4
3
0 0

P112

by bill.gunshannon＠hotmail.com

It's not really Classic Hardware, but it does run some pretty classic OSes.? Anybody here working with the P112?? I have had a couple for ages but never had time to play with them.? I see them now as a possible way to manipulate floppies (including 8") from classic systems so I decided to give it a try.? Problem is, it won't boot anything.? Not the disk that came with it and none of the images I got off the web. Anybody here know anything about them? bill

8 years, 2 months

8
19
0 0

Vintage computing themed domain names for sale

by sellam.ismail＠gmail.com

Hello Folks. I am selling the following two vintage computing themed domain names: vintage-computing.com paleocomputing.com Make an offer on either. Please of course reply directly to me if interested. Thanks! Sellam

8 years, 2 months

1
0
0 0

SGI SN-921 dial box working! (was Re: Seeking software for SGI/Sun dial box)

by ethan.dicks＠gmail.com

On Sun, Apr 8, 2018 at 5:01 PM, Ethan Dicks <ethan.dicks at gmail.com> wrote: > On Sun, Mar 25, 2018 at 3:48 PM, Ethan Dicks <ethan.dicks at gmail.com> wrote: >> SN-921 >> https://upload.wikimedia.org/wikipedia/commons/7/74/Sgi_dialbox_sn-921_fron… > >>>>> https://github.com/hanshuebner/sgi-dialbox-usb/blob/master/dialbox.py >> >> I'm going to test this code out when I have a dialbox in hand. > > I have now tried this and am not having success. I have a traffic > light on the serial cable and I know I'm getting chars out of the host > and that I don't have TxD and RxD swapped. I'm not seeing any > responses from the dial box and the python script does all the > initialization and just sits there. Frobbing the knobs produces no > blinks on the traffic light and no text from the script. OK. I got the script working and two things were impediments: 1) One of the SN-921 pinouts running around on the 'net is incorrect, as I posted. The *correct* place for the ground is DE-9 pin 7. I was apparently getting enough of a parasitic ground to get chars *from* the SN-921 but not *into* the SN-921. As it turns out, it appears the SN-921 as set up for the SGI is mute except for a single status success byte 0x20. If you send it an INIT command (also 0x20), it will respond with its success after a fraction of a second, which leads to another problem... 2) The python script dialbox.py slams the init code and a command to set the dials to auto-report all at once, before the SN-921 has a chance to initialize. So to fix that, I added a few extra lines to send the 0x20 INIT command, pause, check for a 0x20 response (INIT GOOD) _then_ send the AUTO command (0x50 0x00 0xFF), which sets all 8 dials (one bit per dial) to send back a 3-byte packet when twisted. With the custom serial cable fixed and the init sequence fixed in the Python script, I'm now getting the right data stream when I twist any of the knobs. I did get a copy of dialbox.c from http://www.geocities.ws/joekrahn/dialbox.tgz Jim Stephens tracked down that there was a massive GeoCities scan done in 2009 and the file I was looking for happened to be scooped up then. There are a number of dial box and button box command sets in that code which reveals some of the more complex behavior possible. Here's a slice of the command byte definitions... #define DIAL_INITIALIZE 0x20 #define DIAL_SET_AUTO_DIALS 0x50 #define DIAL_SET_AUTO_DELTA_DIALS 0x51 #define DIAL_SET_FILTER 0x53 #define DIAL_SET_TEXT 0x61 #define DIAL_SET_BUTTONS_MOM_TYPE 0x71 #define DIAL_SET_AUTO_MOM_BUTTONS 0x73 #define DIAL_SET_LEDS 0x75 #define DIAL_SET_ALL_LEDS 0x4b It should be possible to write up a protocol definition from studying the code. I do not have one of these button boxes so I can't validate its behavior. -ethan

8 years, 2 months

1
0
0 0

The Famous Computer Cafe

by dmonnens＠gmail.com

Hello, I am trying to find anyone who has recordings of a radio program >from 1982-1986 called The Famous Computer Cafe. This was broadcast on KIEV in Glendale, KFOX in Redondo Beach, and NPR through Santa Monica College (here in 1984-1985). The program contained numerous interviews with all the movers and shakers of computers and software during that period, including Bill Gates, Steve Jobs, and Jack Tramiel. As such, this show is of high historical importance. There was somewhere between 100 and 200 episodes all told. I understand it was an extremely popular program among hobbyists at the time, so was hoping someone from the list might have recordings. If you have any recordings or know someone who might, please let me know! I have contacted the show's hosts, but we have only been able to locate a handful of recordings. Thank you! -- Devin Monnens www.deserthat.com The sleep of Reason produces monsters.

8 years, 2 months

1
0
0 0

Burroughs L8000 San Antonio TX

by billdegnan＠gmail.com

Anyone interested in buying a Burroughs L8000, currently San Antonio TX? If so, contact me via http://www.vintagecomputer.net/contact.cfm and I will put you in touch with the person who contacted me. I already have two or three of these so....just kidding not personally interested in this. Bill

8 years, 2 months

1
0
0 0

Seeking software for SGI/Sun dial box (was Re: IBM 6094-010 "Dials" protocol?)

by Richard.Sheppard＠telus.com

On Sun, Mar 25, 2018 at 3:48 PM, Ethan Dicks <ethan.dicks at gmail.com<http://www.classiccmp.org/mailman/listinfo/cctalk>> wrote: > SN-921 > https://upload.wikimedia.org/wikipedia/commons/7/74/Sgi_dialbox_sn-921_fron… > > DANAHER CONTROLS Dials DLS80-1022 > https://upload.wikimedia.org/wikipedia/commons/c/cd/SGI_dialbox_DLS80-1022_… >>>> https://github.com/hanshuebner/sgi-dialbox-usb/blob/master/dialbox.py > > I'm going to test this code out when I have a dialbox in hand. The Solaris CDs used to have /usr/demo/DIALBOX (and BUTTONBOX) with source code. I think it was meant for xview though so you'd need to pick out the useful bits (if any). Richard Sheppard

8 years, 2 months

1
0
0 0

SGI Indigo Power Supply Pinout?

by ethan＠757.org

Howdy, Working on fixing an old SGI Indigo of mine in prep for VCF East. The issue is once any sort of IRIX kernel is running, it craps out WARNING: Power Failure Detected at a high rate. The SGI Indigo and a few other similar models could push out that error on the local console and perhaps network inbetween the time that AC power was lost going into the power supply and the power supply had discharged enough for system to die. Pretty impressive and strange! I was amazed when I first noticed it, of course now it has come back to haunt me. I have replaced some of the electrolytic caps in the power supply. But in the spirit of troubleshooting, does anyone have any sort of schematics or documentation on the power supply, or the midplane? This is a R4000 Indigo and has the higher output power supply to support bigger CPU and graphics. In the meantime I'm working to document what I can about the power connector and will publish, but I can only get so far without other insight. Thanks -- : Ethan O'Toole

8 years, 2 months

2
2
0 0

Amust Executive up for auction

by trash80＠internode.on.net

Not sure if anyone in the Melbourne (Victoria, Australia) might be interested in this. I only just found about it from a friend of mine in Melbourne. The very famous (well famous here anyway) Kerleys Auction (http://www.kerleys.net.au) in Geelong have listed an Amust Executive computer in tomorrows (10 April) auction. http://www.kerleys.net.au/current-auction Its Lot 177 in the tomorrow's catalogue: http://www.kerleys.net.au/images/auctions/10-04-2018/CAT10-04-2018.PDF >From the only photo it looks in reasonably good condition. http://www.kerleys.net.au/images/auctions/10-04-2018/1-280/DSCN3459.JPG I believe Kerleys will take bids before the auction but not sure of terms - number is (03) 5223 1533 It's not something I'd like in my collection but may interest another Australian collector. Kevin Parker P: 0418 815 527

8 years, 2 months

2
2
0 0

Seeking software for SGI/Sun dial box (was Re: IBM 6094-010 "Dials" protocol?)

by ethan.dicks＠gmail.com

On Sun, Mar 25, 2018 at 3:48 PM, Ethan Dicks <ethan.dicks at gmail.com> wrote: > SN-921 > https://upload.wikimedia.org/wikipedia/commons/7/74/Sgi_dialbox_sn-921_fron… > > DANAHER CONTROLS Dials DLS80-1022 > https://upload.wikimedia.org/wikipedia/commons/c/cd/SGI_dialbox_DLS80-1022_… >>>> https://github.com/hanshuebner/sgi-dialbox-usb/blob/master/dialbox.py > > I'm going to test this code out when I have a dialbox in hand. I have now tried this and am not having success. I have a traffic light on the serial cable and I know I'm getting chars out of the host and that I don't have TxD and RxD swapped. I'm not seeing any responses from the dial box and the python script does all the initialization and just sits there. Frobbing the knobs produces no blinks on the traffic light and no text from the script. So... I'm digging deeper and I've found two references to some code >from around 2002 that can interact with dialboxes, but the sites are no longer up and the internet archive did not save the binary archive files. I'm asking here in the hope that someone saved copies 10+ years ago when these files were still being served... In the following thread on the ccp4bb list, there is a mention of these archives... [ in http://www.ysbl.york.ac.uk/ccp4bb/2003/msg00204.html ] "I'm using SGI dialbox (Part# DLS80-1022) with XFree86 4.0.x under linux, with modified version of the Joe Krahn's dialbox driver. You can get the modified version from http://www.biochem.s.u-tokyo.ac.jp/~ishitani/dialbox/dialbox-new.tar.gz and the original version from http://www.geocities.com/joekrahn/ " So I'm looking for: dialbox-new.tar.gz dialbox.tgz dials.c Apparently Joe Krahn hasn't done much with Open Source in 15 years because looking for him has not been fruitful. Thanks for any bits! -ethan

8 years, 2 months

2
4
0 0

Need help identifying Timex Sinclair ZX81 "Programmer Console" on eBay

by dan＠quakka.com

Hi everyone, I collect Timex Sinclair / ZX81 gear, but have never seen one of these before: https://www.ebay.com/itm/RARE-Vtg-TIMEX-SINCLAIR-ZX81-Computer-PROGRAMMER-C… <https://www.ebay.com/itm/RARE-Vtg-TIMEX-SINCLAIR-ZX81-Computer-PROGRAMMER-C…> Do any of you recognize it? Can you explain its purpose, please? Cheers, -Dan

8 years, 2 months

3
2
0 0

alpha 3000-400S parts for sale

by useddec＠gmail.com

If interested, please contact me off list. Thanks, Paul

8 years, 2 months

1
0
0 0

P112

by cruff＠ruffspot.net

I have a operational P112 with 3.5" floppies, GIDE/CF and CD-ROM. Do you know which ROM you have installed?

8 years, 2 months

1
0
0 0

SGI Indy power supply: identify this diode?

by pete＠dunnington.plus.com

After a recent power cut and a series of glitches as the power was restored, one of my Indys suffered a PSU failure. It's a Sony APS-81 171W unit, SGI P/N 060-0008-001. I've found half a dozen damaged parts, and I've identified a 150R 1W metal film resistor (R135), two trannies (Q105, a 2SC4304 and Q106, a 2SC2785) and a couple of small diodes. One of them (D116) appears to be a 6.2b2 (6.2V 1/2W) zener. The other one I'm not sure about. On the PCB it's labelled D113, and it's adjacent to the 2SC2785. It's very small, with a green band at the cathode end, and the legend "4B" in green - photos at https://www.flickr.com/photos/pnt103/albums/72157667056183978 Oddly, another Sony PSU I looked at had a diode there that looked identical except it's marked "4A". I have an idea what it might be but if anyone actually knows what family or type/value this is, I'd be grateful for any insight. -- Pete Pete Turnbull

8 years, 2 months

4
7
0 0

WeirdStuff going out of business

by aek＠bitsavers.org

Last Day is this Sunday http://www.vcfed.org/forum/showthread.php?63045-WeirdStuff-is-going-out-of-… since I can't attach a picture here

8 years, 2 months

22
27
0 0

8080/8085 Programming books available UK/EU

by mark＠wickensonline.co.uk

A few seminal 8085 programming books available please see album: https://photos.app.goo.gl/Rv7vy9eDrMfGK9gz2 Looking for ?25 including postage to the UK or ?20 plus postage elsewhere. Regards Mark

8 years, 2 months

2
1
0 0

PDP Programming books for sale UK

by shadoooo＠gmail.com

Hello Mark, I sent you an email some hours ago about the books, not sure if it got lost in spam... I would buy them all. Thanks Andrea

8 years, 2 months

1
0
0 0

RL01/RL02 emulator needed -- (was Many thanks to Glen's Vintage Computer Info)

by Flash688＠flying-disk.com

jnc at mercury.lcs.mit.edu (Noel Chiappa) wrote: > Err, which RLV11/RLV12 emulators are you seeing? I know of several RL02 > emulators - Reinhard Heuberger's, and another I can't immediately find my > saved info on - (and one crazy project that turned a real RL02 into a USB > device :-), but you still need an RLV11/12 controller. The only ones I can find now are the ones you mention. Yes, I too can't find my notes on the second one, whatever it is/was. I was *sure* that someone had made a Qbus emulator that used SD cards, but I simply can't find any mention of it now. Right now, it looks like Reinhard Heuberger's board is the best bet. I haven't checked with him yet to see if boards or kits are still available. If I could find a working TDL-12 I would jump on it in an instant. All the older ones (Dilog, etc.) appear to use ST-506 type drives, which introduces its own set of problems. Alan Frisbie

8 years, 2 months

2
1
0 0

PDP Programming books for sale UK

by mark＠wickensonline.co.uk

Please see album: https://photos.app.goo.gl/ZztlMFCSoZcy2ZJz1 Looking for ?20 plus postage likely to be less than ?5 UK. Regards Mark

8 years, 2 months

1
0
0 0

RL01/RL02 emulator needed -- (was Many thanks to Glen's Vintage Computer Info)

by jnc＠mercury.lcs.mit.edu

> From: Alan Frisbie > I need a controller that emulates the DEC RLV11/RLV12 and RL01/RL02 > drives. From my Google searching, I see a couple that use SD or similar > solid state devices. Err, which RLV11/RLV12 emulators are you seeing? I know of several RL02 emulators - Reinhard Heuberger's, and another I can't immediately find my saved info on - (and one crazy project that turned a real RL02 into a USB device :-), but you still need an RLV11/12 controller. Noel

8 years, 2 months

1
0
0 0

WeirdStuff going out of business

by barythrin＠gmail.com

Wow. That's unfortunate. Only been in town twice but was definitely part of my scheduled geekdom tour. So any local stores left for that type of thing? Any word on why the closure? I've always seen a lot of folks in the store (well my 2 times) but i don't know how many purchased. null

8 years, 2 months

1
0
0 0

eBay: Anyone need a DLV11-J?

by jnc＠mercury.lcs.mit.edu

> From: Bill Gunshannon > Caution!! The DSD board has some broken chips and bent pins and all of > them look like they spent time in muddy water. Thanks for catching that. I looked at it, saw that it was a DLV11-J, which I didn't need, and so didn't look any harder. Noel

8 years, 2 months

1
0
0 0

ISO: Corvus Concept parts

by derschjo＠gmail.com

I picked up a Corvus Concept CPU unit about a decade ago now, and I've yet to track down any other parts for it. Looking for keyboards, monitors, drives, peripherals software -- anything. If anyone's got any parts, please drop me a line.? Always wanted to see one run... Thanks, Josh

8 years, 2 months

2
2
0 0

eBay: Anyone need a DLV11-J?

by jnc＠mercury.lcs.mit.edu

This is listed under a useless title: https://www.ebay.com/itm/292503681011 But it's (currently) cheap (don't all bid against each other ;-). Noel

8 years, 2 months

3
2
0 0

RL01/RL02 emulator needed -- (was Many thanks to Glen's Vintage Computer Info)

by Flash688＠flying-disk.com

"peter at rittwage.com" <peter at rittwage.com> wrote: > You don't want to try to repair the controller? There are some custom > IC's on there (it appears) but is largely off-the-shelf TTL... I'm > sure someone on the list has a lot of experience with these and could > repair it or help. Indeed, I DO want to repair it, but that is a project for another day. Right now I need to solve the need for an RL02 emulator, which will let me quickly solve the current problem. Again, does anyone have any experience (good or bad) with any of the RL02 emulators our there? Thanks, Alan Frisbie

8 years, 2 months

3
2
0 0

Apple B&W CRT monitor popping and clicking

by silvercreekvalley＠yahoo.com

Hi all, Recently booted up my B&W Powermac G3, all came up fine including the 17? CRT monitor. However after a second or so, the monitor gives a ?popping? sound and the image on the screen expands then shrinks. This repeats every few seconds. I?m guessing the monitor is on the way out - but as this is a complete B&W system - I wondered what the likely cause is? Thanks

8 years, 2 months

6
6
0 0

DEC DEREP repeater PSU

by binarydinosaurs＠gmail.com

Hi folks, Has anyone ever replaced the PSU in a DEREP with a more modern equivalent? The PSU is an ASTEC but as usual doesn?t have any markings for ratings or pinouts. I found the tech ref online but for PSU problems it just says ?replace? as I?d expect. Test LEDs on the unit itself (and the fuses) show +5 and +12 at 2A. This one suffered a bad heat-based death at some point after the fan seized? Cheers, -- adrian/witchy Owner of Binary Dinosaurs, the UK's biggest home computer collection? t: @binarydinosaurs f: facebook.com/binarydinosaurs <http://facebook.com/binarydinosaurs> w: www.binarydinosaurs.co.uk <http://www.binarydinosaurs.co.uk/>

8 years, 2 months

1
0
0 0

DEC 3000 (alpha) faultfinding

by cctalk＠beyondthepale.ie

I've got a DEC 3000 model 300 and a couple of DEC 3000 model 600 alphas which failed some time ago and the recent Alphaservers thread has rekindled my interest in getting them working again. A couple of years ago, there was another thread "AlphaStation 200 NVRAM Problem" where the Alpha SROM mini console and various items of useful documentation were mentioned. I have now made up an adapter (cable and MAX232 line driver / receiver) as described in that thread to allow me to to talk to the the SROM mini console in my alphas and I am please to find they are all responsive at this level. I also found: "DEC 3000 300/400/500/600/700/800/900 AXP Models System Programmer's Manual Order Number: EK-D3SYS-PM. B01" (d3syspmb.pdf) which describes some of the internals of the machines in question. The mini console commands available on the model 300 are very limited compared to those in the documentation which targets a much later machine. However, it does have mt (memory test) which is not present on the model 600 for some reason. Results from this suggests that all 6 SIMMs present are bad in pretty much all locations. This seems a bit unlikely to me. Perhaps there is a failure in logic which causes the memory not to be accessed at all? Unfortunately, the manual does not seem to give any leads on how to diagnose this further. The em (examine memory) and dm (deposit memory) commands only accept 32 bit addresses meaning they cannot to be used to access input/output areas which require at least 33 bit addresses. However, a little experimentation led me to the existance of ei and di commands which can do this on the DEC 3000 machines and I found I can use di to update the diagnostic LEDs on the machines. The DEC 3000 600 machines both (usually) count down to F0 on their diagnostic LEDs and hang without producting any output on the main console. They do however produce output on the mini console - for example: DEC 3000 - M600 SROM 6.1 Powerup Sequence ff.fd.fb.fa.f9.f8.f7.f6.f5.f4.f3.f2.f1.f0. sysROM 00000033.000006f1 ioROM 00000033.00000162 MCRstat 11111111.808011c0 bnkSize 00000300.00000c01 memSize 000000c0.000000c0 However, they do not provide the SROM> prompt or accept mini console commands unless a I engineer another fault condition such as by pulling out one of the memory risers. I wonder if there is a jumper to enable mini console commands to be accepted without doing this? Looking around the system board, I see a pair of jumper pins labelled J9 hidden under the I/O board which looks like it could do this. Unfortunately, while there is legend on the PCB indicating the function of all other jumpers, there is none for J9 and it is not mentioned in the manual either. On the I/O board, there is one three pin jumper labelled simply "Off" and "On" and it is jumpered to the "On" side. It is close to the SCSI connector so I suspect it is more likely to be something to do with termination or termpwr than the mini console. One of the model 600s sometimes generates a machine check, like this: DEC 3000 - M600 SROM 6.1 Powerup Sequence ff.fd.fb.fa.f9.20. MCHK exc_addr 00000000.00001484 biu_stat 00000000.000022d8 dc_stat 00000000.00000007 fill_adr 00000001.f0080050 fill_syn 00000000.00000000 DataExp aaaaaaaa.aaaaaaaa DataRec aaaaaaaa.aaaaaaaa MCRstat 11111111.808011c0 bnkSize 00000300.00000c01 memSize 000000c0.000000c0 SROM> While this can be useful because it gets me to the SROM> prompt, I can't find anything in the manual which helps me diagnose what might be causing this. The meaning of the contents of biu_stat might be a useful start. The 600 machines have a socketed 27C512 EPROM. I assume this must be the SROM (although I can't see what is serial about it) as the machines fail to update the diagnostic LEDs or write to the mini console if it is removed. I dumped the two EPROMs and compared them and they are identical. However, I can't see any ASCII strings in them. Perhaps the bits are not used in the standard order? The manual suggests that there are 8 different 8KB SROM images present and those other than the "standard" one may be used for testing and diagnostics by setting jumpers. Unfortunatly, there is no further information about these images. The manual hints that the System ROM (SYSROM) (actually an FEPROM) is located at 1 E000 0000 to 1 E003 FFFF, however, looking at the beginning of this area with ei suggests it is in fact the IOROM (also an FEPROM). Hunting around some more, it seems that setting bit 9 of the System Support Register at 1 E004 0100 brings in the SYSROM instead (although the manual suggests bit 7 is also involved which seems unlikely as this bit is one of the diagnostic LEDs). The format of the headers in the SYSROM and IOROM do not exactly match the format given in the manual but they are "close". I wonder if this might be my problem or if the manual is incorrect. If anyone else has a 3000 600, could they take a peek at their SYSROM and maybe we could compare notes? It may be possible to map the SYSROM from a running operating system but as none of my 3000 machines run right now, I am not in a position to try this myself. Regards, Peter Coghlan.

8 years, 2 months

4
12
0 0

RL01/RL02 emulator needed -- (was Many thanks to Glen's Vintage Computer Info)

by Flash688＠flying-disk.com

Several days ago I wrote about my joy of finding a TDL-12 disk controller, emulating four DEC RL02 drives and using a SCSI drive. Sadly, I discovered that the controller is a dead as a doornail. It doesn't respond to any bus address at all. So, I'm back to my original quest: I need a controller that emulates the DEC RLV11/RLV12 and RL01/RL02 drives. From my Google searching, I see a couple that use SD or similar solid state devices. Does anyone here have any direct experience (good or bad) with any of these emulators? I don't mind spending money for a good solution. Thanks, Alan Frisbie

8 years, 2 months

3
2
0 0

PATA hard disks, anyone?

by decguy＠songdog.eskimo.com

The new sysadmin at work is clearing out closets full of junk^H^H^H^H cool old stuff accumulated by the previous sysadmin. There's a big carton full of PATA hard disks. Most of them are in the 4.3 GB - 20 GB range, a few larger, a few smaller. Anyone have any use for these? You can have them for the cost of shipping, or free for local pickup in Bothell, WA. They're going to be recycled as scrap if I don't find a home for them.

8 years, 2 months

21
46
0 0

Instruction video on laserdisk

by ed＠groenenberg.net

Today I received a PDP-11 instruction video on a laser disk, part 3 & 4. The disk partno. is EY-5537E-V2-0001, the title says 'Introduction to the PDP-11, Internal use Only, (c) 1988' Besides that, no indication if the video stream is NTSC or PAL. Anybody have a clou? I want to have the disk read and put the video on youtube eventually. Ed -- Ik email, dus ik besta.

8 years, 2 months

4
4
0 0

Software for AN/UGC-144 Communications Terminal?

by nf6x＠nf6x.net

I posted this originally on the ArmyRadios mailing list, but I think it's just computery enough that it may be of interest here, too. And maybe somebody here even has the answers to my questions! I just got an AN/UGC-144 communications terminal. It looks unused, and it came with cables and manuals (-12 and -30, but not including schematic diagrams or component-level details). It powers up, but fails to boot from its internal hard drive. The screen has some bad rows and columns, and the gas spring that supports the display needs to be replaced. I shared a bunch of pictures on Twitter today as I unpacked it and started playing with it, in this thread: https://twitter.com/nf6x/status/980174491673178112 Here are direct links to some of the more interesting pictures in that long thread: https://twitter.com/nf6x/status/980198067767947264 https://twitter.com/nf6x/status/980202029766230016 https://twitter.com/nf6x/status/980263764325941249 https://twitter.com/nf6x/status/980302909165338624 I haven't found very much about the terminal online yet, and I expect that I have a long road ahead of me as I try to fix the display and see if anything can be recovered from the hard drive. If the original software isn't present on the hard drive and recoverable, then this may be a great big doorstop! But it may also be a fun reverse-engineering project. I haven't dug into it deeply enough yet to determine whether it's built around an embedded PC-clone architecture or is something completely custom. In any case, I'll naturally want to try to dump and disassemble any ROMs I find inside of it. The CAGE code is for Sypris Electronics, and the boot screen shows a Honeywell copyright notice. I found that it tried to access a blank floppy diskette at boot time in the right drive, but I didn't have an MS-DOS boot diskette handy at the moment to see if it could boot from it. I'll give that a try when I have a chance... but probably after Easter. Have any software diskettes, programs, disk images, etc. for this terminal made it out into the wild? I presume that there were boot and installation diskettes that were used for hard drive formatting and software installation, and I would really love to get my hands on anything like that... especially if it turns out the the hard drive in my terminal is blank and/or dead. I'll be satisfied if I can use this rig as a dumb terminal for RTTY use, and even happier if I can do anything fancier with it. -- Mark J. Blair, NF6X <nf6x at nf6x.net> http://www.nf6x.net/

8 years, 2 months

1
0
0 0

DEC BA213 and BA213 S-boxes?

by ethan.dicks＠gmail.com

Hi, All, Watching some of the recent traffic about what newer Qbus boards will and won't work with 2.11BSD, I've remembered a thing I was once looking for. Back when I did DEC hardware for a living, we stopped buying new stuff after we got a MicroVAX-II. As such, I have plenty of LSI-11 to KA630 parts but very little from after that era. I do happen to have 2-3 boards with S-box handles including a KDF-11 CPU and a SCSI card, a great start to a system. What I don't have is the enclosure. I have a BA123 "World Box" and it's great. I know a BA213 is roughly the same size, but I've never had one. The BA215 looks more interesting to me as a match for size and power requirements (1 PSU and 6 slots, half the BA213) but I've never even seen a BA215. Anyone here have much experience with the BA215? Any "gotchas"? So far, from my looking on eBay, I think I spotted one loaded as a VAX. I'm more interested in setting mine up as a PDP-11, so the VAX end of one is not exactly a selling point to me. An empty box would do just as nicely. I'd say 80% of my Qbus work has been with two boxes, the BA-11N and the BA-23, thus all the S-box questions. Thanks for any tips, tidbits and stories. -ethan

8 years, 2 months

4
5
0 0

DEC 3000 (alpha) faultfinding

by cruff＠ruffspot.net

According to the 21066 HRM, the processor loads its initial I-stream from the SROM. All Icache bits are loaded from the SROM, including the cache block metadata. The blocks are loaded in sequential order starting with block 0 and ending with block 255. For the 20166, the Icache is loaded LSB first filling from left to right (i.e. bit 0 of LW0 will be the first bit loaded). This is the resulting order of each cache block: BHT LW7 LW5 LW3 LW1 V ASM ASN TAG LW6 LW4 LW2 LW0 I thought I had some code do unmultiplex each bit stream from an SROM image and then reconstruct the resulting memory image, but I can't find it or I just thought about doing that.

8 years, 2 months

3
2
0 0

Looking for opinions...

by useddec＠gmail.com

There are probably no perfect answers to this problem. I am looking for opinions, not criticism. I do not want to start arguments, nor get anyone here, especially Jay, pissed off. I found a stack of DEC microfiche a few nights ago. It's probably about 12 inches tall, and contains PM Procedures, IPBs, Manuals, Tech Info, and several type of Logistics, BOMs, vendors, etc which I will deal with later. Most of it is "company confidential", not that it matters anymore. The bulk of my microfiche is still missing. Several months ago there was a discussion here about breaking up sets. this is not a "set". It is made up of bunches found in different places at different times. I'm guessing a "set" of this would be an inch or two thick. My short list of options for disposal are as follows in order of current preference are: 1 Sort to get several sizable sets, sell the rest as partials. A LOT of sorting 2 Take requests to cherry pick, and sell as few smaller sets. Still a LOT of sorting. 3 Call Al. Oh, he gets a crack at whatever he needs anyway. 4 Sell it as a lot 5 Sell on e-pay. 6 Put it back where I found it. The first 3 are going to take a lot of time. Thanks in advance, Paul

8 years, 2 months

24
61
0 0

Instruction video on laserdisk

by commodorejohn＠gmail.com

I don't know where you're located, but I'm in the US and have an NTSC Laserdisc player. If someone can hook me up with a video capture card, I'd be happy to copy the video for you.

8 years, 2 months

2
1
0 0

How to set DZ11 line speeds under RT-11 V4?

by fritzm＠fritzm.org

Hi all, I've now had some success getting MU-BASIC configured and running on multiple terminals under RT-11 V4 in simh, with a hardware configuration similar to that in my real PDP-11/45. I have a serial console + DZ11 in both configurations. When SYSGEN-ing RT-11 V4, the only speed initialization options offered for the DZ11 lines are 110 or 300 baud. Is there a utility or incantation which will allow me to reconfigure these after RT-11 is booted? I scanned the RT-11 V4 docs last night, but came up empty (there is an "unsupported" SPEED.SAV in the distribution, but it looks like it only works with PDTs, and I couldn't find anything tucked away in the SET command or other places either). It looks like I could write some MACRO code to try and set this using the .MTGET/.MTSET programmed requests, but I thought I'd ask here in case there is some known prefab way to do this that I missed looking through the docs? cheers, --FritzM.

8 years, 2 months

1
1
0 0

RL02 Question

by jnc＠mercury.lcs.mit.edu

> From: Aaron Jackson > I have tried three controllers, two r/w modules and two servo > controllers. I'm beginning to think the drive is fine and there is a > problem with the RLV21 controller. Err, think you mean RLV12 QBUS controller board, right? Anyway, you've already tried ("three controllers") swapping that out? If you have, perhaps there's a problem with a cable and/or the terminator? However, at this point, sub-system swapping is probably not going to be the best way to make progress. I think you're going to have to actually debug the problem; i.e. dive in and work out what's happening wrong, and why, and trace it back to the origin. Luckily, for this generation (and before), DEC produced wonderful technical manuals, which go into full detail of how the thing works. With that in hand, the investigative process is a lot easier; you don't have to work out how the thihg works by looking at the prints, it's all laid out in detail. And tech manuals for both the RL02 drive and RLV12 controller (EK-RLV12-TD-001) are available online, as are the prints (MP01282 for the RLV12). So, I'd sit down with the RLV12 tech man and read through the section on the drive<->controller bus (section 3.3). Then start looking at what the two are saying to each other on the bus, and figure out what's actually going wrong. >From there, you'll know where the source of the problem is, and can chase it further. I know this sounds like it would be time-consuming, but when you think about the time/energy you've already put into swapping things around, chasing this problem, it won't be. Noel

8 years, 2 months

3
3
0 0

towards a working PDP: Anyone has a PDP 11/35 or PDP11/40 panel for $$$ to offer?

by p.gebhardt＠ymail.com

Hello all, As I never came across a complete unit of an early PDP-11 with lights-and-switches console, I decided 5-6 years ago to figure out, if I can't build one of out of different parts. It seemed possible to get there if I focus on parts for a 11/35 or 11/40. 5 years ago, I came accross a backplane for such as system. Two years later, I was lucky to purchase an almost complete board set (one board missing, the M7232) from another classic computer enthusiast. Last year, I got a BA11-F chassis with the power supply. Over all those years, I looked out for a 11/35 or 11/40 panel (KY11-D), but I never was lucky to come accross one.On epay US, somebody is offering the plain PCB, but the seller says that he cannot ship to Europe :-( My frustation pushes me now to ask, if anybody on this list has such a panel with the electronics board that he would consider to offer me for some $$$ to help me building a complete machine? I don't mind the panel color, e.g., if it's from a front-end PDP-11 of some bigger DEC system, or if the silkscreen is damaged or even missing. It would be great for me to get an early PDP-11 up and running and connect it to peripherals such as an RK07 that are in my collection.? I am located in Germany. Contact me off-list, if you have something to offer, please.? Best regards,Pierre ------------------------------------------------------------------------------- Pierre's collection of classic computers moved to: http://www.digitalheritage.de

8 years, 2 months

1
0
0 0

Identifying an aluminum panel

by kylevowen＠gmail.com

I feel like I should know what this panel goes to...I found it in my garage when cleaning up. Any ideas? http://i.imgur.com/u4LMNqE.jpg Thanks, Kyle

8 years, 2 months

5
5
0 0

break on pdp11 serial ports

by jnc＠mercury.lcs.mit.edu

> From: Sytse van Slooten > digging through the documentation of KL-11 and DL-11 I did find > references to generating a break (bit 0 in the XCSR). But not on how it > would be received. ... How did a DL-11 like interface signal the > reception of a break? As JohnW says, framing error. FWIW, the UART chips used back then actually produce a 'framing error' output, which is sent straight into that bit in the RCSR. > And how did the operating systems and software deal with it? Was it > actually used at all? Different systems used it for different things. Unix V6 used 'break' on dial-up lines as the signal to switch speeds when you first connected up - it would try 110, then 150, then 300. (Later this got extended, I expect - too lazy to check.) I see the hacked PWB1 Unix at MIT used it to send an interrupt: if (c & FRERR) { signal(tp->t_pgrp, SIGINT); return; } That's as far as my knowledge extends, others may know of more uses. Noel

8 years, 2 months

1
0
0 0

CXY08 and DELQA compatible with 2.11bsd?

by bob＠jfcl.com

Does anyone know offhand if the CXY08 (M3119) and DELQA (M7516) work with 2.11bsd? I think the CXY08 has the same programmer interface as the DHV11, and I'm hoping it works with the 2.11bsd dh driver. Ditto for the DELQA and the qe driver. If somebody knows for sure, though, I'd appreciate it if you can save me the trouble of installing it all just to find out it doesn't work. Thanks, Bob

8 years, 2 months

5
7
0 0

RL02 Question

by aaron＠aaronsplace.co.uk

Sorry to keep bothering you all with RL02 questions. I think I am nearly there. It seems my head cleaning in a warm bath of isopropyl alcohol was a success. I bought a tested RL02 pack and loaded it - no bad sounds, I can extend the heads all the way. So that's good. I have supposedly a working RL02K pack, and seemingly good heads. After I load a pack however, it goes into fault mode. Checking through the test points on my scope, there is no survo burst data until I push the heads 3-5mm further forward. So it seems to me that the heads are not loading far enough into the pack. I loosened the head alignment screws to move the heads all the way forward, tightened them back up, and tried loading the pack again. It stopped again, 3-5mm short of track 0. So moving the heads forward didn't seem to make any difference. I have tried a different control board, and read/write amplifier board, with no success. Has anyone else experienced this? Is there some sensor which I am not seeing? Thanks, Aaron. -- Aaron Jackson PhD Student, Computer Vision Laboratory, Uni of Nottingham http://aaronsplace.co.uk

8 years, 2 months

3
6
0 0

RT-11 V4 MU-BASIC help

by fritzm＠fritzm.org

Hello all, I would like to try and get MU-BASIC working on my PDP-11/45, under RT-11 V4. The best bits I've been able to find to work with so far are the RK05 image here: http://bitsavers.trailing-edge.com/bits/DEC/pdp11/discimages/rk05/rt11v4-mu… ...but I've not had much success getting this to work under simh. Using the 1USER.CNF configuration file in this image, no matter how I configure the machine, I get either traps, halts, or stack violations when issuing the first command in basic. Trying to rebuild MU-BASIC using the indirect files in the image results in a linker barf on some undefined symbols. Has anybody else here had much luck getting MU-BASIC up and running under RT-11 V4? Is there an alternate image or distribution kit somewhere that I could try to work with? thanks much, --FritzM.

8 years, 2 months

4
8
0 0

TRS-80 Siting

by bill.gunshannon＠hotmail.com

I hate to suggest that people actually watch the garbage, but a recent Safe Auto Insurance commercial features a girl typing on a TRS-80 Model 4 with the badges removed. It's the one that starts out with a Disco skit.? The TRS-80 shows up in the very last part. bill Don't shoot me, I'm only the messenger. :-)

8 years, 2 months

1
0
0 0

break on pdp11 serial ports

by cclist＠sytse.net

Hello all, I've been playing around with some ideas for designing some hardware to connect peripherals to an fpga for my vhdl pdp-11. One of the things that should definitely be on there, next to sd cards and leds... are some serial ports for console terminals etc. I've spent some time to create a prototype usb to serial thing that handles more than one port. Works kind of neat. While doing that, I stumbled on the concept of break. Up to now in all of the pdp2011 history I have ignored it, the serial port that sits at the pdp-11 side of things is about the most minimum that does the job. And that is good enough for a lot of things, actually - I didn't really miss a break signal so far. Anyway, digging through the documentation of KL-11 and DL-11 I did find references to generating a break (bit 0 in the XCSR). But not on how it would be received. That's where the questions start. How did a DL-11 like interface signal the reception of a break? And how did the operating systems and software deal with it? Was it actually used at all? I think to remember several occasions of impatiently banging the break key back in the day, but it is a bit fuzzy why (and if it had any result). anyway, I'm trying to judge whether it makes any sense to put effort into making the break thing work on my serial converter thing... any kind of input is greatly appreciated! cheers Sytse

8 years, 2 months

2
1
0 0

RAID? Was: PATA hard disks, anyone?

by cctalk＠ibm51xx.net

-------- Original message -------- From: Chuck Guzis via cctalk <cctalk at classiccmp.org> Date: 3/28/18 10:02 AM (GMT-08:00) To: Paul Koning via cctalk <cctalk at classiccmp.org> Subject: Re: RAID? Was: PATA hard disks, anyone? >I know of no RAID setup that can save me >from stupid. Chuck, As we say in my day job "there is no curing stupid" ;) -Ali

8 years, 2 months

8
9
0 0

DEC 3000 (alpha) faultfinding

by cruff＠ruffspot.net

On the AXPpci33 board, the SROM is also an 8 bit device. What happens is that the CPU reads in a bit stream into cache at power up reset, where the specific bit stream is selected by the jumper position on the board. In effect the SROM can contain up to 8 bit streams. Some of them will make use of the SROM console port.

8 years, 2 months

2
1
0 0

RAID? Was: PATA hard disks, anyone?

by cctalk＠ibm51xx.net

-------- Original message -------- From: Fred Cisin via cctalk <cctalk at classiccmp.org> Date: 3/27/18 5:51 PM (GMT-08:00) To: "General Discussion: On-Topic and Off-Topic Posts" <cctalk at classiccmp.org> Subject: RAID?  Was: PATA hard disks, anyone? How many drives would you need, to be able to set up a RAID, or hot swappable RAUD (Redundant Array of Unreliable Drives), that could give decent reliability with such drives? 10 - Two sets of 5 drive? RAID 6 volumes in a RAID 1 array. You would then need to lose 5 drives before data failure is imminent. The 6th one will do you in. If you haven't fixed 50 percent failure then you deserve to lose your data.? Disclaimer: this is my totally unscientific unprofessional and biased estimate. My daily activities of life have nothing to do with the IT industry. Proceed at your own peril. Etc. Etc. -Ali

8 years, 2 months

3
2
0 0

SGI SN-921 dial box (978-0804) (was Re: IBM 6094-010 "Dials" protocol?)

by ethan.dicks＠gmail.com

On Sun, Mar 25, 2018 at 6:09 PM, Ethan Dicks <ethan.dicks at gmail.com> wrote: >> SN-921 (2.1mm barrel jack for +5V) >> https://upload.wikimedia.org/wikipedia/commons/7/74/Sgi_dialbox_sn-921_fron… > > http://yehar.com/blog/?p=3471 > > The (Seiko?) SN-921 can apparently be powered via DE9 or the 2.1mm > jack next to it... > > 1. GND > 2. SERIAL OUTPUT (?9 V) > 3. SERIAL INPUT > 4. POWER IN +5 V > 5. POWER IN +5 V > 6. NC > 7. NC > 8. GND > 9. NC Now that I've poked around in the innards, I can say that this pinout has a slight mistake in it. It should be: 1. GND 2. SERIAL OUTPUT (?9 V) 3. SERIAL INPUT 4. POWER IN +5 V 5. POWER IN +5 V 6. NC 7. GND 8. NC 9. NC There are mentions here and there about how to hook up this dial box using the +5V power jack and DE9 pins 2, 3, and 7. I can confirm from direct examination that pin 7 is a ground and 8 is NC on the PCB (and that 4 and 5 are connected directly to the center pin of the 2.1mm power jack). -ethan

8 years, 2 months

1
0
0 0

Looking for opinions...

by jnc＠mercury.lcs.mit.edu

> From: Liam Proven > And yet, 3 generations later Can we please keep _all_ politics off the list? It didn't go so well last time. Noel

8 years, 2 months

1
0
0 0

Many thanks to Glen's Vintage Computer Info

by Flash688＠flying-disk.com

I don't know if Glen Slick is on this list, but I owe him one! I am working on an elderly PDP-11/23 system running RSX-11M v3.2 -- too old to know about MSCP disk controllers like the RQDX1/2/3 and compatibles. It is only sysgened for RK05, RL01/2, and an incompatible 3rd-party disk, but neither the RK05 or RL01/2 controllers are present. To do my work, I thus need an RL02 and controller... OR something that emulates an RL02. I had planned to post a note here today, asking for recommendations for RL01/2 (RLV11) emulators, but got distracted. Instead, I set about making an inventory of several boxes of Q-Bus cards I had accumulated over the years. Most were DEC, but a bunch were weird 3rd-party controllers, one of which was a TD Systems TDL-12. What the hell is a TDL-12? My Google searching led me eventually to Glen's Vintage Computer Info https://sites.google.com/site/glensvintagecomputerinfo/home and his page on the TD Systems TDL-12: https://sites.google.com/site/glensvintagecomputerinfo/td-systems/tdl-12 The TDL-12 turns out to be a Q-Bus SCSI controller, emulating up to four RL01/2 drives -- exactly what I needed! Glen's web page even includes a PDF of the original TD Systems manual for the board. So, Glen, whoever and wherever you are, I thank you from the bottom of my heart for creating and maintaining a web page about this orphan controller. You have saved me a lot of time, effort, and probably a bit of money as well. As an added bonus, Glen also has a page for an obscure HP Q-Bus logic analyzer card, which I also have. But that's a project for another day. Thanks, Alan Frisbie

8 years, 2 months

3
3
0 0

IBM 6094-010 "Dials" protocol?

by mbbrutman＠brutman.com

Picture here: https://i.imgur.com/ClCw070.jpg Does anybody know how to talk to this thing? I've got one of these devices but I don't have a reference for the protocol. It's a serial device so it's probably not terribly complicated, but trying to figure it out by throwing random bytes at it might take a few years. SA23-2780-01 - "Option Instructions IBM 6094 010 Dials for AIX" should have the description of the protocol, but I can't find this document anywhere. https://www.ibm.com/support/knowledgecenter/en/ssw_aix_71/com.ibm.aix.files… gives some hints on how it is programmed - in particular it alludes to "setting granularity" (sensitivity) which would be in addition to reading the dials. Somebody with access to an AIX box and that "special file" might be able to dig up the commands. I know IBM has professional archivists so I can try them for the document referenced above if I can't find it other ways. And I could probably find the micro-controller inside, hope the ROM is readable, and try to disassemble that, but that would be a last ditch effort. Regards, Mike

8 years, 2 months

9
11
0 0

PATA hard disks, anyone?

by cctalk＠ibm51xx.net

-------- Original message -------- From: Chuck Guzis via cctalk <cctalk at classiccmp.org> Date: 3/27/18 4:43 PM (GMT-08:00) To: "Tapley, Mark via cctalk" <cctalk at classiccmp.org> Subject: Re: PATA hard disks, anyone? Digging around on the pointer from Al to backblaze, I found this, which, to me is far more meaningful in terms of presentation of data: Interesting but consistent with my informal observations. My Hitachi enterprise class 4gb hdd are still going strong after multiple power outages and almost 5 years of 24x7 on time. Granted not much reading and writing occurs but the fact that they are spinning is probably the biggest wear and tear on them. Helium drives? Only if you have the money to replace them yearly and have a RAID 1 set of a RAID 6 volume.... -Ali

8 years, 2 months

7
8
0 0

WTD: Dell ML6000 (or similar) LTO library, Mid-Atlantic East Coast

by ethan＠757.org

While this slightly deviates from classic computers, I've been on the hunt for a surplus LTO library around the mid-atlantic East Coast for a bit. The Dell ML6000 which is made by someone else is what has my eye. We have one at work, lame robot that is very slow at changing tapes and looks sad compared to the STK machines I used to work around. But the density of the tape carts stored in the cabinet just can't be beat. I love some of the larger IBM fridge sized LTO units but the tape density given cabinet size just isn't there, but the scale out by adding cabinets side by side is cool -- if I only had a basement. Say 280 carts for huge IBM box versus 133 carts in the Dell unit at 15 rack units high. No brainer. The Dell ML6000 is also known as Quantum i500, and there is a super sexy IBM version and also a HP badged version. A few have popped up down in Florida and AZ for ~$100 or so with LTO3 drives which is ideal. But not proper timing. I have a LTO5 drive or two for these that came from a trash bin, so in my case I can upgrade the drives. Tapes don't generate heat or use electricity when sitting idle, so it seems ideal to backup my home NAS boxes and hoards of software for classic computers, arcade / video games and laser show 8 and 16 channel digital audio tape dumps. -- : Ethan O'Toole

8 years, 2 months

2
1
0 0

Photorealistic frontpanels for DEC PDP simulations under SimH

by j_hoppe＠t-online.de

Guys, there are updates to the photorealistic PDP-8/10/11/15 panel simulations for SimH, code name "BlinkenBone". * Added bigger images for 3000 pixel width screens. * made PDP-11/70 panel behaviour compatible with the real machine ? (after tests performed at the PDP-11/70 "Miss Piggy" at LCM in Seattle, ? thanks to Rich Alderson & Josh Dersch). ? Oscar Vermeulen's upcoming PiDP1170 replica will also benefit. * Added Mike Hill's BLINKY animation as PDP-11/70 application. * Optically enhanced the PDP-10KI10 panel: ? Added rack background of the real KI10 at LCM. * Merged with SimH code base from march 2018 * Some people want to reanimate a physical panel with "BlinkenBone" too, or did already. http://retrocmp.com/projects/blinkenbone/setting-up-a-blinkenbone-project ? Finally I can supply the hardware, a tested set of BeagleBone Black, BlinkenCape and BlinkenBoard. ? I can't get the price below 200?, there's this penalty for manual small batch production (including some self-exploit). Doc root page: http://www.retrocmp.com/projects/blinkenbone Download: https://github.com/j-hoppe/BlinkenBone/releases As usual, there are precompiled distributions for Win32, Ubuntu x86 & x64, Raspberry Pi and Beaglebone. Just unzip and start some of the shell scripts. Enjoy, Joerg

8 years, 2 months

2
2
0 0

WTB Sun keyboard

by stephane.tsacas＠gmail.com

Hi, My keyboard is dying. I'm looking for a type 7 "UNIX Keyboard" model : 320-1367-02 Picture : https://imgur.com/JUumgkz I'm in Paris, France. Thanks -- ??phane

8 years, 2 months

1
0
0 0

Issues of Communication of the ACM for sale

by stephane.tsacas＠gmail.com

Hi, I'm selling issues of the famous ACM magazine. I don't have a list, but at least from 2010 and up. If you're not in a hurry, shipping cost is quite low, < 6 euros for 2 Kg, < 8 for 3 Kg. Shipping from Paris, France. Note that if you're in France, shipping is more expensive ! If you're interested, make me an offer. Thank you, -- ??phane

8 years, 2 months

1
0
0 0

RL02 Question

by shadoooo＠gmail.com

Hello, I'm not an absolute expert, but I successfully fixed a couple of RL02 in the past. Adjustment to the head is only useful for azimuth, I think. The radial position will be adjusted continuously using the servo tracks, so there's no absolute position adjustment at all. If the drive fails during spinup, I would check at least the following: - the presence of spindle sector signal after digital conversion of pulses >from analog signal coming from the pickup. - having disabled the servo linear motor (there's some jumper to setup, check the maintenance manual), perform the motor spinup, then load slowly the heads on the disk by hand, until you find the servo tracks. - with an oscilloscope check the presence of analog signal of the servo tracks on both heads, and it's digital counterpart after amplification and threshold detection (expected level values in the manual). If you see something strange, e.g missing or too short pulses, try to adjust the gain with the trimmer on the head board - enable again the servo, then load again My 2 cents. Andrea

8 years, 2 months

6
12
0 0

DTC 3250

by cisin＠xenosoft.com

I just stumbled on a DTC3250, & "Installation Guide" 8 bit ISA SCSI + 4 floppy Firmware: "GSH53A" The floppy interface MIGHT work for HD on a 5150/5160? (with appropriate software) Condition unknown Anybody need one? -- Grumpy Ol' Fred cisin at xenosoft.com

8 years, 2 months

3
2
0 0

Compaq 9000 Series Rack Screws

by cctalk＠ibm51xx.net

> F.Y.I. the links to the pictures from the linked to page aren't > publicly accessible. As grant has pointed out the pictures will not show up unless you are a VCF member. However, the screws are very similar to this in shape: https://monsterbolts.com/products/6mm-m6-x-1-0-stainless-steel-button-head-… I have done some more digging and I believe the screws are Button Head 10mm M6 screws w/ T30 drive. The problem is that the head diameter needs to be 9.2mm wide. The screws above (and most other one's I have found) are 10mm or wider. The HP screws I mentioned earlier are 10.26mm wide and they of course will not clear the side panels. So again if anyone has OEM Compaq screws they want to part with I am your man. Thank you. -Ali

8 years, 2 months

2
2
0 0

Wiring Harnesses (was: RL02 Question)

by binarydinosaurs＠gmail.com

Years ago I was troubleshooting an old SuperMicro beast that was running a newspaper printing press. It kept shutting down randomly but if I hit the power button it would come up. Then randomly go down again minutes or an hour later. I spent many hours testing and swapping modules in and out of this thing >from a working machine and at one point it would only power up if the front box that contained the power switch module and CDROM/floppy were out of the enclosure and separate on the bench (but still connected to the motherboard by an data/power cables). If I got a long screwdriver and earthed this front box to the main enclosure the machine would go down immediately. Power switch itself tested fine with a meter but I found there was a hidden reset swtich that wasn't in use so I desoldered and swapped them over. All problems went away and the customer practically carried me at shoulder height around the press hall. -- adrian/witchy Owner of Binary Dinosaurs, the UK's biggest home computer collection? t: @binarydinosaurs f: facebook.com/binarydinosaurs w: www.binarydinosaurs.co.uk ---------- Forwarded message ---------- From: allison via cctalk <cctalk at classiccmp.org> Date: 27 March 2018 at 13:32 Subject: Re: RL02 Question To: Aaron Jackson <aaron at aaronsplace.co.uk>, "General Discussion: On-Topic and Off-Topic Posts" <cctalk at classiccmp.org> > Long short story. I got my RL02 directly through DEC while I was a > engineer there.It was a pile of parts in the back lab. The story was it was pulled > from a customersite as FS could not make it work at install. Seems despite being new > just about everything that could be swapped apparently was and no one could get it > to spin up. So I made a deal if I get it working its mine (ok, to be part of > the 11/23 in my office, which later would become mine). After assembling it and > testing it sure enough it didn't spin and would turn slowly for a few moments and quit. > Drag out the meter and start testing voltages. I found the motor starting > cap (known new) had odd voltages. A bit of ohming out later it was the crimped > faston connector at the end of the power line going to the capacitor. What > was wrong was crimped but the wire was never stripped so there was no connection. > The only thing never swapped was the power wiring harness. The pile of swapped > boards and even heads was impressive. I got the drive and word got around > that it was me that solved the riddle. I troubleshot the problem, and > didn't swap it to death.

8 years, 2 months

1
0
0 0

Compaq 9000 Series Rack Screws

by cctalk＠ibm51xx.net

Ok, A bit too new for this list but still hoping someone can help me out: I am in need of at least six (prefer 10) Compaq 9000 Series OEM Rack screws to mount a side panel. I believe these are M6 screws. On the side that had the panel already mounted the OEM screws are star screws approximately 0.5" long. I have looked online and on some of the rack accessory suppliers and have found M6 screws which I believe are from HP racks. Aside from the fact that the OEM is a Philip's head (not a big deal - security is not a huge issue) the HP ones are just a tad bigger. The length of the HP screws should be okay (I think). However, the flange is just a bit too big and it catches on the side panel so you can't screw the screw in all the way (w/o damaging the side panel). The OEM star screws do not do this. If anyone has any spares they can part with or knows where I can order some (and definitely get the OEM ones vs. the after market/HP ones) I would appreciate it. Thank you! BTW pictures and measurements can be found in this thread on VCF: http://www.vcfed.org/forum/showthread.php?62877-WTB-OEM-Compaq-9000-Series-R ack-Screws&p=507884#post507884 -Ali

8 years, 2 months

1
0
0 0

Identifying vacuum tube module

by kylevowen＠gmail.com

Anyone knows what these go to? https://imgur.com/a/CpxLs Thanks, Kyle

8 years, 2 months

3
2
0 0

set help

by j_hoppe＠t-online.de

8 years, 2 months

1
0
0 0

System/36 Password Cracking

by ball.of.john＠gmail.com

For those following from the VCFed thread I have been working on an IBM 5363 that I have managed to get running up to the IPL sign on. For everyone else this project is being documented at http://www.vcfed.org/forum/showthread.php?62860-IBM-5363-IBM-System-36 >From there while I know who last owned the machine (from picking it up at their dock) me and my contact at this company have been unable to dig up the MASTER or administrator login information. I ahve a couple leads that might be either the username or password but so far no comnination has worked. Yes I am aware of the old USENET post regarding cracking the login on a 5362 ( https://groups.google.com/forum/#!topic/comp.sys.ibm.sys3x.misc/Vi57cbw1ofQ ) however the CE panel on the 5363 is a lot more simplified and I cannot do several of the steps. Also I do not have the system key but I can probably hotwire it Does anyone know of an alternate procedure for recovering or finding a lost MASTER login? -John

8 years, 2 months

1
0
0 0

VCF West exhibit registration is open

by cctalk＠snarc.net

VCF West XIII will be held August 4-5 at the Computer History Museum in Mountain View, California. Exhibit registration is open: http://vcfed.org/wp/festivals/vintage-computer-festival-west/vcf-west-exhib…. ________________________________ Evan Koblentz, director Vintage Computer Federation a 501(c)3 educational non-profit evan at vcfed.org (646) 546-9999 www.vcfed.org facebook.com/vcfederation twitter.com/vcfederation

8 years, 2 months

1
0
0 0

LSI11 CPU Microm

by dj.taylor4＠comcast.net

I was trying to put together a minimal PDP-11/03 using a quad width M7264 CPU and got nothing, no ODT prompt.? I'm not sure the board is working. Searching the internet I came across this page which described a M7264 CPU board with a 'bad' MICROM http://www.datormuseum.se/computers/digital-equipment-corporation/qbus Quoting the page; "Using a logic analyser showed that the MICROM without label is not behaving well." Anyone know how a logic analyser would be used to determine this?? Other hints to debug this board? Doug

8 years, 2 months

3
2
0 0

R.I.P. Robert T. "Doc" Suding

by spacewar＠gmail.com

I just learned from the April 2018 issue of QST that Robert T. "Doc" Suding, W0LMD, has died. Suding cofounded and was chief design engineer of The Digital Group, an early microcomputer company in Denver (1974-1979).

8 years, 2 months

6
8
0 0

Shipping a Flexowriter

by kylevowen＠gmail.com

Does anyone have any tips on preparing a Flexowriter for shipping? Any thoughts as to crate vs. pallet? Thanks, Kyle

8 years, 2 months

13
19
0 0

Somewhat random QBus backplane / chassis question

by derschjo＠gmail.com

Hi all -- I've got an 11/03 backplane here (designated as an "11/03 EA" originally but marked as "Model changed from EA to AA") inside a small chassis w/power supply, model "OH780-A."? (So it was at some point in its life the front-end to a VAX-11/780.)? As far as I can tell, it has a standard H9270 backplane (4-slot, quad width) in it. The chassis appears to work fine when I have an actual LSI-11 in there (I've been experimenting with an 11/23, but I do have an 11/03 boardset that works in it). What I want to do with the chassis is use it with a UNIBUS->QBus bridge I have, as a Qbus backplane for a SCSI controller (and maybe other things) for my VAX-11/750.? I have encountered an oddity in doing so, and I've looked at the documentation and I remain puzzled.? The oddity is this:? If I don't have an LSI-11 CPU board in place in the chassis, the power supply won't come up properly.? (The +5V appears to pulse, the kind of behavior I'd expect with a shorted or heavily loaded supply rail somewhere). Here's a basic rundown of what I've observed: - If I put an 11/23 or 11/03 CPU in, everything works fine. - Doesn't matter what slot the CPU's in either, as long as there's a CPU board somewhere in the thing, all's well. - Doesn't matter how heavily or lightly loaded the backplane is; I've tried it with just a QBus SCSI controller, I've tried it with the backplane stuffed full of boards. Since I want to use this as a simple QBus backplane, I don't want to have a CPU board in place.? I haven't seen this behavior before (but then, I can't recall trying to run a Qbus backplane without a CPU in it either).? I thought I knew QBus fairly well, so I assume I'm overlooking something obvious.? Or perhaps there is a fault here with the chassis, somehow.? I figure someone here will have the answer immediately and I'll slap my forehead... Thanks as always, Josh

8 years, 2 months

2
2
0 0

Remnants of local Commodore Users' Group being offered for free

by barythrin＠gmail.com

Whoever or whichever group does get it, i hope if they have any files or interesting info the rest of the clubs can help store. null

8 years, 2 months

1
0
0 0

R.I.P. Robert T. "Doc" Suding

by jnc＠mercury.lcs.mit.edu

> From: Al Kossow > The only place I ever saw an Apple I when it was for sale. Don't you wish you'd bought one - and kept it? :-) Noel

8 years, 2 months

1
0
0 0

Help with IC identification

by binarydinosaurs＠gmail.com

Hi folks, I'm looking for info on a few 8 pin DIPs that are in a cache battery module. They're marked thus: 4973 AK W79B 4965 AF W83A Anyone? I've not traced pinouts yet but maybe someone else's google-fu is better than mine today. Cheers, -- adrian/witchy Owner of Binary Dinosaurs, the UK's biggest home computer collection? t: @binarydinosaurs f: facebook.com/binarydinosaurs w: www.binarydinosaurs.co.uk

8 years, 2 months

1
0
0 0

DEC Field Guide > equivalent available for Data General?

by u.tagge＠gmx.de

Hi all, is there somewhere a list of DG modules which includes also 3rd party/OEM, ... like it is available for DEC? Would be good to know what the following is: 107-000621 02 107-000621 03/11 107-001632-00 107-0016320/02 107-000718-00 107-000181-04 107-000187-16 107-000187-15-30 AB020116-00 107-000621-03 107-001768-02 107-001768-03 107-0017680-1E 107-00053905 Zetaco SCZ-2 >500-453-00 K >500-542-00 K Many Greetings Ulrich

8 years, 2 months

4
4
0 0

Remnants of local Commodore Users' Group being offered for free

by cclist＠sydex.com

This is in Eugene, OR. I received the following email on the local Freecycle-type list: ---------------------------------------------------------------- I have all of the "Lane County Commodore Users Group" (LCCUG) inventory including (but not limited to) the following : Keyboards, one monitor, transformers, two disc players for 5 1/2 inch floppies, cassette tape player, games, a whole lot of instructions, dozens of empty discs, dozens of full discs, and much more. Plus a 25-plus pound lap top (SX-64) ! More than a regular car trunk can hold . Many items in original boxes. LCCUG is no longer exists. For a classic computer buff this would be a gold mine. It is amazing what this old computer was able to do - 30 years ago! 18th and Chambers area - Eugene. jimsav97405 at yahoo.com ------------------------------------------------------------------- I have nothing to do with this offer. FYI --Chuck

8 years, 2 months

1
0
0 0

FPGA implementations of DEC processors

by chd＠chdickman.com

There are enough pdp8 fpga that they have started to calll themselves YAPDP8FPGA. So what are the really good FPGA DEC processors? -chuck

8 years, 2 months

6
6
0 0

PDP8/e programmers consoles

by chd＠chdickman.com

So the PDP8/e used the KC8-EA programmers console which has incandescent indicator lamps and the PDP8/f used the KC8-FL programmers console which has LED indicator lamps. Why? The maintenance manual says that LEDs are more reliable. The operation is as far as I know the same. The LED version doesn't need the +8VDC supply, but that seems an advantage for it. I remember reading that the EAE had some revision dependencies with the console, so were there bus timing problems with the LED console that limited it to short buses? Maybe this changed over time, but it overlapped long enough for them to have both described in the maintenance manual and specific to the application. Another console question... Has anyone ever seen a PDP8/i style console for the PDP8/e? Looking at the way the PDP8/e console functions, it should be possible to time multiplex all the register to the data bus so they are all visible at once when the machine is halted. -chuck

8 years, 2 months

7
13
0 0

DEC RL cables, terminator, etc.

by useddec＠gmail.com

Several list members have asked me about RL cables, etc. I have finally gone through most of them. If anyone needs any parts, please contact me off list. Thanks, Paul

8 years, 2 months

1
0
0 0

AlphaServers

by john.h.blake＠gmail.com

I've got two, the first being an 3000/400 64mb with two 146 gb SCSI-320 drives running on converters, one with openBSD 6 and the other with openvms 8.4 running headless. I doubt I'll ever be able to find the monitor, much less the needed cables and keyboard/mouse to turn it into the desktop it was supposed to be, so I've got a color turbochannel framebuffer if anyone has any use for it. The second is an alphaserver ds10l with the 617mhz EV67 processor, 1.5 gb ram and a radeon video card on the sole pci port, which runs openvms 8.4 on one hard drive and the most recent available version of unsupported debian linux on the other (I think it's sid?) as a workstation. Nekochan.net is a fair resource for hobbyist knowledge, possibly the only place online where people are still futzing about with Tru64. comp.os.vms on usenet (or the info-vax email gateway) is where all of the latest news and deep tech discussion goes on. vcfed.org has a very healthy DEC forum too.

8 years, 2 months

4
4
0 0

Message Reply with quotation

by gerardcjat＠free.fr

Hello Guys, It seems that YOU can reply to cctech message(s) with "quoting" the answered message. How do you do that ??? Thanks for your help. Gerard

8 years, 2 months

5
4
0 0

Andromeda Systems DC11

by bill.gunshannon＠hotmail.com

I asked this on USENET, I don't suppose it would hurt to ask here as well. Anybody here remember the Andromeda DC11? More importantly, does anyone still have Andromeda stuff laying around? The module used something called "Personality Cards" which were actually just connection adapters for different kinds of disks. I am trying to find a couple (I'd be happy with one) WPC8F adapters for connecting 8" disks to my modules.? Any chance anyone has these taking up space?? Of course, I would also take other kinds of adapters, well, except for the WPC5FA.? That's for the RX50 and even I don't have any more of them left. bill

8 years, 2 months

2
2
0 0

LSP10-NW (printer interface for KI10?)

by mattislind＠gmail.com

I have received this for a retired DEC service engineer: https://i.imgur.com/pJkcsHe.jpg?1 https://i.imgur.com/zwpSbrg.jpg According to the label it is a LSP10-NW made by DEC CSS. Previous owner claims it is for a KI10. I don't really know. I have no real use for it except for the flip-chips. Anyone has a need for such a thing or just the backplane? /Mattis

8 years, 2 months

1
0
0 0

Quad density Pertec

by gerardcjat＠free.fr

Reply to :I note that the Kennedy incremental 7 inch reel drive in the NASA flight case hasn't attracted a lot of interest. That sample tape that I got, however does verify that the parity track on this telemetry stuff is unused. So that explains the 8 data inputs with no parity on the NASA model. --ChuckWell, at least ONE person was interested ... Me .... BUT the vendor does not offerinternational shipping ( to France ), and does not care answering mail :-(Though tape transport is already "packed" ;-)Gerard

8 years, 3 months

1
0
0 0

Vintage computer event - Melbourne Australia - this Sat 24 March

by malcolm＠avitech.com.au

Melbourne's first Mini Vintage Computer Faire Various vintage microcomputers will be on display in Mooroolbark this weekend More details are available here -> https://www.facebook.com/events/1935562660092538/ The event runs from 10am to 4pm this Saturday (24 March 2018) and is at: Mooroolbark Terrace Shopping Centre 66 Brice Avenue, Mooroolbark 3138 Come along and enjoy (subject to any last-minute changes!): Replica Apple I Microbees TRS-80s Dick Smith Super 80 PDP-8/f with ASR33 Teletype Original Space Invader machine ..... and much, much more. I am not an organiser, but will be there as an exhibitor. If you are within driving distance, please come along and join in. Your support will help to encourage a larger event next year! Malcolm.

8 years, 3 months

1
0
0 0

DEC VR150 montior

by dj.taylor4＠comcast.net

Does anyone have a schematic for this DEC monitor?? I have one that has good video but doesn't seem to want to respond to video input.

8 years, 3 months

1
0
0 0

FS: More S-100 related hardware from Sellam's collection

by sellam.ismail＠gmail.com

Hello Folks. I posted more S-100 gear for sale, including several early MITS Altair boards. Please follow the link below if interested. The new Altair listings are right after the update. http://www.vcfed.org/forum/showthread.php?61192-Sellam-s-S-100-Hardware-Sof… If interested, please do inquire directly to me by e-mail via < sellam.ismail at gmail.com>. Thanks! Sellam

8 years, 3 months

2
2
0 0

ISO: Harris Micro-12 (HB-61000) docs

by derschjo＠gmail.com

Hi all -- Got me a Harris Micro-12 (AKA the HB-61000), this is a single-board computer based around the Harris 6100 (PDP-8 on-a-chip) microprocessor.? I'm working on bringing it back to life and I'm trying to find docs and schematics for it. There's a high-level overview starting on page 5-4 of http://bitsavers.org/components/harris/1979_Harris_CMOS_Microprocessor_Volu…, but that's the most I've found.? Right now it looks like the FLAG 2 signal on the PIE chip (HD-6101, discussed in the aforementioned manual) is holding the 6100's RUN line low; I don't see anything telling the PIE to do that at reset, nor is anything else attached to that signal that I've been able to find, so I'm wagering that the chip is faulty at the moment.? (If I pull the PIE chip out the CPU appears to be running.)? Schematics and/or docs would make this a lot easier. Anyone have a copy of these? Thanks in advance, Josh

8 years, 3 months

1
0
0 0

UCSD p-system manuals and disks?

by mattislind＠gmail.com

I received these nice binders. https://i.imgur.com/L80ZGusl.jpg I think that most of them are already available online. Not sure about the UCSD Pascal manual? One of the binders contained some disks. https://i.imgur.com/FYIBbmjl.jpg Are these disks available online already or should I dump them? Bitsavers seems to have the Mac version. /Mattis

8 years, 3 months

5
5
0 0

Register your VCF East exhibits soon

by cctalk＠snarc.net

Don't procrastinate. http://vcfed.org/wp/festivals/vintage-computer-festival-east/vcf-east-exhib…

8 years, 3 months

1
0
0 0

AlphaServers

by BHuntsman＠mail2.cu-portland.edu

Place your wagers... How many more years do you think it'll take before decent, practical-sized Alphas, like the DS15, and to some degree, the DS10, will be obtainable at hobbyist-friendly prices? I have an ES47 I got for a price I could stomach, but it's sans rail kit, drinks power like it's going out of style, and can anchor a 40-ft yacht. Anyone out there do Alphas anymore?

8 years, 3 months

23
45
0 0

Four Unibus boards from radiation dose measurement system.

by mattislind＠gmail.com

Hello! I have four unibus boards that came in a 11/34 which was used for radiation dose measurement at a hospital. Three of them are made by Computer Design & Application inc and is a three board set interconnected with over the top flat cables. It has some kind of AMD 29xx based bitslice processor with 2903,2910 and 2914 chips. One board has some kind of dedicated memory one board has 4 TRW chips which I think are AD converters. https://i.imgur.com/lMvhxOp.jpg?1 https://i.imgur.com/LEVN5Qp.jpg https://i.imgur.com/kcSnDRy.jpg https://i.imgur.com/ZfFrq3j.jpg Then there is some kind of serial com board with four UARTs on it. https://i.imgur.com/YvnTlxq.jpg Is there any interest in these boards? Trade for something interesting DEC stuff maybe? Or something else? /Mattis

8 years, 3 months

5
6
0 0

Compaq Storageworks V5.4 kit for SUN Solaris

by Flash688＠flying-disk.com

I'm cleaning out my accumulation of "stuff" and there are several things that aren't worth the effort of putting on ebay. If anyone on this list wants them, they are yours for the cost of shipping. The first item is: QB-5JCAG-SA Compaq Storageworks RAID Array 450 V5.4A Platform Software Kit for SUN Solaris Contains: AG-R20SE-BE Software CD "RAID Array 450 V5.4A for SUN Solaris" AE-RBDYB-TE Software Product Description SPD 64.64.05 AA-R20TD-TE Release Notes AA-R20RD-TE RAID Array 450 V5.4 for Solaris 2.x Installation Guide AA-R24LA-TE StorageWorks Command Console (v1.1) User's Guide EK-HSZ50-CG HSZ50 HSOD v5.1 Array Controller Configuration Manual EK-HSZ50-SV HSZ50 HSOD v5.1 Array Controller Service Manual EK-HSCLI-RM HSZ50 HSOD v5.1 Array Controller CLI Reference Manual It weighs just under 5 pounds, so I estimate the shipping cost would be $10 to $20. Send me an email if you want it. If I don't hear from anyone in a few days, it goes into the dumpster. Alan Frisbie

8 years, 3 months

1
0
0 0

ounting screw threads for VR201?

by Flash688＠flying-disk.com

Ethan Dicks <ethan.dicks at gmail.com> wrote: > I don't happen to have a VR201 here right now to measure directly (or > I would just do that), but IIRC, there's a threaded mounting insert on > the bottom (for the "E.T. Stand", if nothing else), I want to > fabricate a shelf clip for a VR201 and am seeking the diameter/thread > pitch for the insert. Does anyone have that info handy? It's likely > larger than 1/4-20 from what I remember. There are four brass inserts in a trapezoidal pattern, each threaded 1/4-20 (National Coarse). The trapezoid is 7.0" center-to-center for the two nearest the screen, and the rear ones are 5.0" center-to-center. It is 5.0" between the front (screen) pair and the rear pair. This is for a VR201-B -- other dash-variants may be different. If there is a base with a single large threaded insert, it may be an adapter that goes between the VR201 and the stand. Now, could someone please tell me the pinouts for the 15-pin connector? I would like to use it to view RS-170 video, if possible. Alan Frisbie

8 years, 3 months

4
4
0 0

FS: Early Revision Commodore 64 computers

by sellam.ismail＠gmail.com

Hello Folks. In the continuing saga of sorting through a big batch of Commodore stuff >from my collection, I've listed 6 different early revision Commodore 64 computers for sale. Complete details and links to photographs are on the VCFed forums here: http://www.vcfed.org/forum/showthread.php?62641-Sellam-s-Commodore-Sales-Th… Please do inquire directly to me by private e-mail for fastest response. Thanks! Sellam

8 years, 3 months

2
1
0 0

Mounting screw threads for VR201?

by ethan.dicks＠gmail.com

Hi, All, I don't happen to have a VR201 here right now to measure directly (or I would just do that), but IIRC, there's a threaded mounting insert on the bottom (for the "E.T. Stand", if nothing else), I want to fabricate a shelf clip for a VR201 and am seeking the diameter/thread pitch for the insert. Does anyone have that info handy? It's likely larger than 1/4-20 from what I remember. -ethan

8 years, 3 months

2
2
0 0

PDP8/e programmers consoles

by jnc＠mercury.lcs.mit.edu

> From: Allison >> What about warm white LEDs, though? ... maybe they are available in >> bulb replacement form? > I used a supply of dead bulbs to make mine. a little heat and the glass > goes, a resistor and a 3mm led and good to go. Urr, I'm not up to making them! I was really hoping for the plug-in replacement ones in white... They used to make replacements in red (we replaced the bulbs in our -11/45 with them, BITD), so I was hoping. Anyone know of a contemporary source for LED replacements for front panel bulbs? (Of any colour!) Noel

8 years, 3 months

2
1
0 0

PDP-11 DIV instruction lossage

by jnc＠mercury.lcs.mit.edu

> I'll have to redo my kludgy fix to gmtime() ... I guess I'll have to fix > it for real, instead of my kludgy fix (which extended it to work for > 16-bit results). :-) > ... > And on the -11/23: > Note that the returned 'quotient' is simply the high part of the dividend. Heh. I had decided that the easiest clean and long-lived fix was to just to do it right, using the long division routine used in the V7 C compiler runtime: http://minnie.tuhs.org/cgi-bin/utree.pl?file=V7/usr/src/libc/crt/ldiv.s and I vaguely recalled reading a DMR story that talked about that, so just for amusement I decided to re-read it, and looked it up: https://www.bell-labs.com/usr/dmr/www/odd.html (the section "Comments I do feel guilty about"), and it's lucky I did, because I found this: Addendum 18 Oct 1998 Amos Shapir of nSOF (and of long memory!) just blackened (or widened) the spot a bit more in a mail message, to wit: 'I gather the "almost" here is because this trick almost worked... It has a nasty bug which I had to find the hard way! The "clever part" relies on the fact that if the "bvc 1f" is not taken, it means that the result could not fit in 16 bits; in that case the long value in r0,r1 is left unchanged. The bug is that this behavior is not documented; in later models (I found this on an 11/34) when the result does fit in 16 bits but not in 15 bits ... which makes this routine provide very strange results!' So this code won't work on an 11/23 either (which bashes the low register of the pair; above). I'd have been groveling in buggy math, again... Caveat Haquur (if you're trying to run stock V7 on a /23 or /34)! Noel

8 years, 3 months

1
0
0 0

DEC bus edge connectors

by jnc＠mercury.lcs.mit.edu

> From: Charles Dickman > Does anyone have DEC bus edge connectors they are willing to sell? > I would like to do some OMNIBUS interface prototyping and I need a way > to connect to the bus back-plane. Have you looked through Douglas Electronics' offerings? They have a lot of DEC-backplane compatible boards that might be what you want, e.g.: http://www.douglas.com/index.php/18-de-77.html this one. Noel

8 years, 3 months

3
2
0 0

PDP-11 DIV instruction lossage

by jnc＠mercury.lcs.mit.edu

So, I have discovered, to my astonishment, that the double-word version of the DIV instruction on the PDP-11 won't do a divide if the result won't fit into 15 bits. OK, I can understand it bitching if the quotient wouldn't fit into 16 bits - but what's the problem with returning an unsigned quotient? And, just for grins, the results left in the registers which hold the quotient and remainer is different in the -11/23 (KDF11-A) and the -11/73 (KDJ11-A). (Although, to be fair, the PDP-11 Architecture Manual says 'register contents are unpredictable if there's an overflow'.) Oh well, guess I'll have to redo my kludgy fix to gmtime() (the distributed version of which in V6 qhas a problem when the number of 8-hour periods since the epoch overflows 15 bits)! I guess I'll have to fix it for real, instead of my kludgy fix (which extended it to work for 16-bit results). :-) I discovered this when I plugged in an -11/73 to make sure the prototype QSIC (our RK11/etc emulator for the QBUS) worked with the -11/73 as well as the -11/23 (which is what we'd mostly been using - when we first started working on the DMA and interrupts, we did try them both). I noticed that with the -11/73, the date printed incorrectly: Sun Mar 10 93:71:92 EST 1991 After a certain amount of poking and prodding, I discovered the issue - and on further reading, discovered the limitation to 15-bit results. For those who are interested in the details, here's a little test program that displays the problem: r = ldiv(a, b, d); m = ldivr; printf("a: 0%o %d. b: 0%o %d. d: 0%o %d.\n", a, a, b, b, d, d); printf("q: 0%o %d. r: 0%o %d.\n", r, r, m, m); and, for those who don't have V6 source at hand, here's ldiv(): mov 2(sp),r0 mov 4(sp),r1 div 6(sp),r0 mov r1,_ldivr rts pc So here are the results, first from a simulator: tld 055256 0145510 070200 a: 055256 23214. b: 0145510 -13496. d: 070200 28800. q: 0147132 -12710. r: 037110 15944. This is _mathematically_ correct: 055256,0145510 = 1521404744., 070200 = 28800., and 1521404744./28800. = 0147132. And on the -11/23: a: 055256 23214. b: 0145510 -13496. d: 070200 28800. q: 055256 23214. r: 037110 15944. Note that the returned 'quotient' is simply the high part of the dividend. And on the -11/73: a: 055256 23214. b: 0145510 -13496. d: 070200 28800. q: 055256 23214. r: 037110 15944. Note that in addition to the quotient behaviour, as with the /23, the 'remainder' is the low part of the dividend. Noel

8 years, 3 months

1
0
0 0

PDP-11 floating CSRs: 760010, or 760100?

by fritzm＠fritzm.org

Hi folks, I have a question about floating CSR allocation on PDP-11s. Both the 1976 and 1981 versions of the PDP-11 peripherals handbook indicate the floating CSRs are to be allocated starting at address 760010. However, both the XXDP FLOAT program and simh's autoconfig suggest I should set my DZ11 (first floating CSR device in my config) to 760100. Anyone know what gives? thanks, --FritzM.

8 years, 3 months

2
2
0 0

allocate floating vector for DR11-C in simh pdp11 autoconfig?

by fritzm＠fritzm.org

Hi folks, I have found it very convenient to maintain a simh configuration that parallels the physical hardware configuration of my PDP-11/45. I'm just about to add a DR11-C for a physical interface that I am building -- this will "grab" a floating interrupt ahead of a DZ11 that I already have in the machine. Does anyone here know of convenient way to inform simh's autoconfig that I wish to insert a DR11-C? cheers, --FritzM.

8 years, 3 months

1
1
0 0

PDP8/e programmers consoles

by jnc＠mercury.lcs.mit.edu

> From: Allison > you have to pull the panel apart to replace them, gets tiring. Modern > yellow LEDs are nice and bright, and don't burn out. > Less digging in the box is a good thing as over time fumble errors can > hurt it. Agree about replacing lamps - we switched to LEDs BITD because replacing burned-out lamps (especially when you're trying to fix some _other_ problem) when there's something better available is just, silly. > Modern red leds at 8mA are very much brighter. However the yellow look > more like lamps. What about warm white LEDs, though? The ones we used in the QSIC indicator panel are, to me, pretty much indistinguishable from the lights as I recall them from BITD. I mean, maybe if I had them sitting next to each other, I could tell, but... Those are SMD, though, but maybe they are available in bulb replacement form? Noel

8 years, 3 months

2
1
0 0

Sperry Univac UTS-40 Terminal doc anyone?

by curiousmarc3＠gmail.com

I am the temporary caretaker of a Sperry UTS-40 "intelligent" terminal (very green screen, Z-80 based terminal from the late 70's or early 80's) which I grabbed on eBait for sending parts to Dominique Carlier over in Belgium. The CRT, power supply and character generator seem to work (gives a very sharp semi-random geometric display on power-on, sometimes with a few nicely drawn characters interspersed), but the darn thing does not seem to boot on reset. The picture goes away and weird sound is emitted from the speaker after a long beep-of-death. I was wondering if anyone had service documentation. Or a dump of the firmware. Al, anything that crossed your desk? Marc

8 years, 3 months

2
1
0 0

PDP11/03 BA-11M Front panel switch replacement

by dj.taylor4＠comcast.net

I have a BA11-M box with the usual front panel control, however it was damaged and all three switches have been sheared off.? The LED's and the circuit card that connects to the power supply appear to be OK.? I would like to repair it and put it back into service.? Is there a replacement for those switches? Doug

8 years, 3 months

4
5
0 0

DEC bus edge connectors

by chd＠chdickman.com

Does anyone have DEC bus edge connectors they are willing to sell? I would like to do some OMNIBUS interface prototyping and I need a way to connect to the bus back-plane. In my mis-guided youth I resorted so sawing them off perfectly good boards. I would rather not do that again. If anyone has prototype boards they have designed with fingers or dead boards they would part I will take them. My methods are crude, but effective. -chuck

8 years, 3 months

1
0
0 0

Noel idea you were into raddar so much too cool!

by couryhouse＠aol.com

all in the ?title

8 years, 3 months

1
0
0 0

radar history

by jnc＠mercury.lcs.mit.edu

> From: Steven Malikoff > I also have a book 'RADAR How it all began' by Jim Brown ... > incredibly precise recollection of the engineering Wow, thanks for that incredibly valuable pointer. My copy just arrived, and it's fabulous; it documents in great detail a part of the story that's little-known, which is the industrialization of the early radar work. There are a number of books from people on the research side (Watson-Watt, Bowen, etc), but not much on the industrial side. There is an obscure book: Frank Rowlinson, "Contribution to Victory: An Account of Some of the Special Work of the Metropolitan-Vickers Electrical Company Limited in the Second World War", Metropolitan-Vickers Electrical Company, Manshester, 1947 (which covers a lot of stuff, not just the radar work), but it doesn't have a lot of technical detail. What it _does_ have a lot of large, excellent B+W photos of the early CH, CHL etc transmitters (which MetroVick built), but not much technical detail of them. That book, and Brown's book, are a marvellous pairing, since he has the detailed description, but no images! A very complementary pairing. Noel

8 years, 3 months

1
0
0 0

Various Software and Documentation for shipping + donations (round 10)

by mtapley＠swri.edu

All, More of the stack. if any of this interests you please contact me via Private (not list) email at mtapley at swri.edu. If you do want something, send me your shipping address and exactly what you want. I'll get back to you with estimated shipping costs (USPS media rate where possible) as soon as I can. You send me payment (any method is acceptable; USPS does not recommend cash in the mail) and I will ship when payment arrives. If you want Fed-Ex or something different from USPS media let me know at your first contact and I will price that for you. If you can afford to send slightly more than costs, I'll collect up the surplus for Cindy and get it to her. If more than one person wants the same thing, it goes to the person sending me the earliest time-tagged email. If Al K. wants anything for Bitsavers, he gets priority (even if his is not the first email) up until it leaves my hands. There will be multiple sets of email from me, each with a short list of things, unless/until someone asks me to quit. Thanks for your attention! - Mark This list is all Books (down to and including pamphlets), no software included. ????????? Adobe Photoshop for Macintosh, Version 3 (Classroom in a Book), 1994. American Heritage Dictionary: 3rd edition for Mac. 32 pages. Communicator 4 quick-study guide. Laminated folder. DeltaGraph Pro 3 Users Guide, 2nd edition. 1993. Excel 5.0 Advanced, Macintosh, student manual. Logical Operations. 1994. Excel: Mastering Excel 5 for the Mac (An Insiders Guide). Thomas Chester and Julia Kelly. 1995. Eudora Mail Pro, educational use. V. 3.0 user manual & quick reference guide. FrameMaker. Using Framemaker release 5, Windows and Macintosh. 1995. Inspiration user manuals. Getting Started manual. Idea book. Netscape: Official Netscape Communicator 4 Book. Macintosh edition. Pi? James. 1997. Now Up-to-date and Now Contact (user manuals). (Two different versions, to match the two different versions on disk we have, I imagine.) Office: Getting Started. The On-line Research Handbook. Hayden Mead and Andy Clark. 1997. Port Replicator: Users Guide. Micronpc.com 1999 PowerPoint: Using PowerPoint 4 for Macintosh. Que, 1994. Quicken version 5.: Users Guide for Macintosh Perform Users. Quicken 5 for Macs for Dummies. Stephen L. Nelson. 1994. The Student?s Guide to Doing Research on the Internet. Dave and Mary Campbell, Addison-Wesley. 1995. vi: Learning the vi editor. Linda Lamb, O?Reilly & Associates, Ltd. 1990. Word: The Macintosh Bible Guide to Word 6. Maria Langer. ?Includes Power Macs.? 1995.

8 years, 3 months

8
10
0 0

Anyone have a Fujitsu M2451E 130mb tape drive manual?

by aek＠bitsavers.org

I have a couple of carts I'd like to read, found a drive today, talks SCSI but not common command set. It seems to act more like a disk than a tape (read block makes the tape move), but mode sense doesn't return anything sensible. The only thing I've ever been able to turn up on these drives is a mention in a Fuji product brochure

8 years, 3 months

1
1
0 0

cctalk Digest, Vol 42, Issue 14

by fred＠MISER.MISERNET.NET

> Date: Tue, 13 Mar 2018 14:28:11 -0600 > From: Grant Taylor <cctalk at gtaylor.tnetconsulting.net> > Subject: Re: cctalk Digest, Vol 42, Issue 13 > Message-ID: > <6a172546-d8f1-13b9-f843-8fdba5799f09 at spamtrap.tnetconsulting.net> > > If power / cooling / noise wasn't an issue, I'd also be interested in an > Multiprise 3000. > But, I'm happily married and I would like to keep it that way. The power requirements aren't that bad, are they? I think Guy Sotomayor (spelling, apologies if I'm butchering ...) has a MP3K that I believe I bid against him on eBay once, and he ended up getting it (which made me feel a bit better). It's what I call a 1/4 fridge size. There were/are multi MP3K's on eBay currently that I've been watching, and one didn't know if there was an OS on it (Not sure I'd want to fight that battle with IBM, although a corner of the Internet lengthy forum post (yes, anecdotes are not evidence) leads me to believe they at least are "sympathetic" to hobbyists, but they won't publically admit it. ... but I still didn't want to chance getting a paperweight. The other one is way too much for me $ wise. I have a basement and 220V available. For an IBM Mainframe of my own, damn the power bill. :) As long as it doesn't have the awful whine of an Alpha DS10-L I don't think my wife would mind. I will admit to myself that at some point there will be a limit to how many systems I can have at the house though running 24/7.... :) Fred

8 years, 3 months

2
1
0 0

3100/90?

by ftg888＠elbonia.org

I am looking into getting a VMS Machines up and running and or Open/netbsd you mentioned you had a few to donate or sale thanks. Sent from my iPhone > On 14 Mar 2018, at 11:55, Liam Proven via cctalk <cctalk at classiccmp.org> wrote: > > On 14 March 2018 at 11:06, Adrian Graham via cctalk > <cctalk at classiccmp.org> wrote: >> >> I'm in the process of giving >> some of them away though because they take up too much room. > > The OpenBSD project are, or were, looking for donations of high-end > VAXstations. I offered them a VAXstation 4000/60 (Red Hat offered to > sponsor shipping from London to Canada) but after some > toing-and-froing, Theo DeRaadt turned it down. > > Unfortunately, I believe RH has now lost my machine. :-( > > But if anyone is willing to donate a /90 or similar, he might be interested. > > -- > Liam Proven ? Profile: https://about.me/liamproven > Email: lproven at cix.co.uk ? Google Mail/Hangouts/Plus: lproven at gmail.com > Twitter/Facebook/Flickr: lproven ? Skype/LinkedIn: liamproven > UK: +44 7939-087884 ? ?R (+ WhatsApp/Telegram/Signal): +420 702 829 053

8 years, 3 months

3
2
0 0

800 and 1600bpi 9 track test data

by aek＠bitsavers.org

There are two gzip'ed files up now of analog digitized 9 track data under http://bitsavers.org/projects/9track containing two files of 16 bit incrementing data patterns blocked 512 bytes/blk and the tach signal from a Qualstar 1260 running at 50 ips. The data can be viewed using Salea's Logic app in simulation mode if anyone has burning curiosity what a 1/2" tape block looks like. I made these as test data today for Len Shustek's 9 track readtape project https://github.com/LenShustek/readtape

8 years, 3 months

2
2
0 0

a bit off topic - looking for someone w/7 track 1/2" analog

by pete＠petelancashire.com

comp for 1 - 7/8 IPS like to get all tracks digitized https://photos.app.goo.gl/IMcgjxugzKMuIvKv2 will put on open file server then sell the tape -pete

8 years, 3 months

2
2
0 0

FS: Commodore items from Sellam's collection

by sellam.ismail＠gmail.com

Hi Folks. It's time for the Commodore collectors to get their turn. I've created a separate thread for Commodore and related items for sale from my collection. I will be continuing to add Commodore stuff to this thread as I come across it. The list is here: http://www.vcfed.org/forum/showthread.php?62641-Sellam-s-Commodore-Sales-Th… If you are interested in anything then as usual for fastest response please do reply to me by e-mail via <sellam.ismail at gmail.com>. Thanks! Sellam

8 years, 3 months

1
0
0 0

Speaking of tapes and good ideas, but...

by cclist＠sydex.com

During my browsing, I've run across mention of the Emerson "Tape Pac" 2000 series, a half-inch cartridge tape system targeted at minicomputers, and it seems, the PDP-11. Here's a mention in IEEE Computer, about the new products at the 1976 NCC: https://www.computer.org/csdl/mags/co/1976/06/01647391.pdf (That was about the same time as "The Milpitas Monster") I can't find of photos of the thing. Has anyone run into one of these? --Chuck

8 years, 3 months

1
0
0 0

XT/370 microcode

by seefriek＠gmail.com

>> I am not at liberty to post the document. > >This? ... >Also: ... >If so, it might be this: ... There's a difference between "I am not at liberty..." and "what anyone can google...".

8 years, 3 months

3
3
0 0

cctalk Digest, Vol 42, Issue 13

by fred＠MISER.MISERNET.NET

On Tue, 13 Mar 2018 cctalk-request at classiccmp.org wrote: > Date: Tue, 13 Mar 2018 04:25:26 +0000 > From: Benjamin Huntsman <BHuntsman at mail2.cu-portland.edu> > Subject: AlphaServers > Message-ID: > <MWHPR03MB257387ED466A847E328DC5D6E4D20 at MWHPR03MB2573.namprd03.prod.outlook.com> > > Anyone out there do Alphas anymore? I'll pile on with my $0.212 (two cents plus tax). I started with a VAXStation 4000/90A. Still have it. Absorbed that system into SIMH and upgraded to a Alphastation (server?) 255. Sold that the 255 and upgraded again to my current DS10, running OpenVMS 8.3. Typing on it now in fact, ssh'ed in from $work. Luckily, I used to work for a company that had data processing services heavily invested in OpenVMS/DEC/Compaq/HP gear. I'm sure I acquired the systems over the years for well below market rates. I could probably sell the VAX 90A for a pretty large sum of $. ... but I really don't want to ... because then I'd have the money and not the VAX. :) If the power bill was free I would upgrade again .... but I have enough 24/7 equipment running in the home office. :) ... and I'm always hunting for more! (an iSeries, perhaps a Multiprise 3000, etc ... ) Fred

8 years, 3 months

2
1
0 0

"The Quest for a Universal Translator for Old, Obsolete Computer Files"

by lproven＠gmail.com

The Quest for a Universal Translator for Old, Obsolete Computer Files To save bygone software, files, and more, researchers are working to emulate decades-old technology in the cloud. by Jessica Leigh Hester March 08, 2018 https://www.atlasobscura.com/articles/how-to-open-old-computer-files ________________________________ >From the sound of this, it strikes me that several of the people/organizations that the author spoke to don't know much about running older software that _will_ work on modern hardware... -- Liam Proven ? Profile: https://about.me/liamproven Email: lproven at cix.co.uk ? Google Mail/Hangouts/Plus: lproven at gmail.com Twitter/Facebook/Flickr: lproven ? Skype/LinkedIn: liamproven UK: +44 7939-087884 ? ?R (+ WhatsApp/Telegram/Signal): +420 702 829 053

8 years, 3 months

1
0
0 0

SGI Origin 2000 Detailed Pics

by phreakshowtelco＠gmail.com

Here is detailed pics of the SGI origin 2000. Its in my shop tonight hoping we can identify whats here. Image heavy https://imgur.com/a/mdlCW Also these 19 racks came with it and it looks like some old cluster stuff in them https://imgur.com/a/feoEq

8 years, 3 months

2
1
0 0

Reading a PDP-11 RL02: Anyone Around the U.S. West Coast?

by unifoundry＠gmail.com

Greetings, I have an old PDP-11 RL02 that I would like to read, to preserve its data for archival purposes. Ideally I would like to extract and store every block on the disk. I am in southern California but would be willing to drive a day or so to anyone who still has an RL02 disk drive on a PDP-11 or VAX and can read it. I can bring a computer with X/Y/Zmodem/Kermit and RS-232 cables if that helps. Thanks, Paul Hardy

8 years, 3 months

2
2
0 0

AlphaServers

by rlloken＠telus.net

On Tue, 13 Mar 2018, Benjamin Huntsman via cctalk wrote: > Anyone out there do Alphas anymore? Well my AS4100 is running OpenVMS even as we speak. I have an Alphastation 500 here doing nothing. I arranged for somebody to get two free DS20Es last year so, yes, I still do alphas. Intel? Don't need no stinkin' intel around here. -- Richard Loken VE6BSV : "...underneath those tuques we wear, Athabasca, Alberta Canada : our heads are naked!" ** rlloken at telus.net ** : - Arthur Black

8 years, 3 months

1
0
0 0

GRI 771 Keyboard Info

by systems.glitch＠gmail.com

All, I'm looking for info on a George Risk 771 parallel ASCII keyboard. I've got one but no documentation or existing cabling. I'd like to interface it to my Poly-88. Thanks, Jonathan

8 years, 3 months

3
3
0 0

XT/370 microcode

by spacewar＠gmail.com

As the most obvious example of the impedance mismatch between 370 architecture and 68000 microarchitecture, the 68000 is hardwired to have eight each data and address registers, not sixteen GPRs, and microcode can't easily paper over that. Similarly, the 8087 microarchitecture has hardwired support for binary floating point normalization, and microcode can't efficiently force that to do radix 16 normalization. Both problems could be surmounted (inefficiently) with enough microcode, but the chips were designed with no significant extra microcode ROM and PLA capacity.

8 years, 3 months

6
7
0 0

Texas Instruments Silent 703/707 print head anyone?

by Martin.Hepperle＠MH-AeroTools.de

Hi, last weekend I cleaned and restored a TI Silent 703 printing terminal. A rather common type with its whopping 300 baud transfer rate - nevertheless a piece of history. It was easy to fix a broken trace on the keyboard PCB (corrosion) and to roughen the idler roller for better grip on the paper. Now there is one issue left: The print head is missing one dot (infinite resistance: burnt out) and one dot prints weak (resistor seems to have twice the resistance of the others, which are all around 95 Ohms). As these terminals were produced in large numbers and the printhead/ribbon cable combo was a user serviceable part someone might have some spare parts... So: if you have a new or used part #2310472-0001 printhead, thermal I would be interested. It is a 10 wire ribbon cable with the print head. It was used in the 703 and 707 and probably also in other devices of the TI 700 Silent family. Martin

8 years, 3 months

1
0
0 0

are there scanned copies of Honeywell computer journal in pdf or? have several bound volumes 68-69 and also 73... tightly bound... if scanned already somewhere will just put on shelf her and consider no further action

by couryhouse＠aol.com

are there scanned ? copies of Honeywell?computer journal in pdf or? ?have several bound? volumes 68-69 ?and??also ?73... ?tightly bound... ?if ?scanned ?already? somewhere will just put on shelf her and consider?no further action ? ed# www.smecc.org

8 years, 3 months

1
1
0 0

Various Software and Documentation for shipping + donations (round 10B)

by mtapley＠swri.edu

All, More of the stack. if any of this interests you please contact me via Private (not list) email at mtapley at swri.edu. If you do want something, send me your shipping address and exactly what you want. I'll get back to you with estimated shipping costs (USPS media rate where possible) as soon as I can. You send me payment (any method is acceptable; USPS does not recommend cash in the mail) and I will ship when payment arrives. If you want Fed-Ex or something different from USPS media let me know at your first contact and I will price that for you. If you can afford to send slightly more than costs, I'll collect up the surplus for Cindy and get it to her. If more than one person wants the same thing, it goes to the person sending me the earliest time-tagged email. If Al K. wants anything for Bitsavers, he gets priority (even if his is not the first email) up until it leaves my hands. There will be multiple sets of email from me, each with a short list of things, unless/until someone asks me to quit. Thanks for your attention! - Mark This list is all Software. Some of it appears to match the books in the previous list, which is why this is titled round 10B - if you are interested in one of these, let me know to look for the matching manual (if I have it). ????????? Adobe Acrobat 4.0, education version Adobe Photoshop 3.0, 8 disks DeltaGraph Professional for Macintosh. 3 disks. 1991. DeltaGraph Pro 3. 1994. 4 disks. EarthLink Sprint Internet Access Software: Total Access 2.0, Mac or Windows, with a book called ?Getting the Most out of the Internet,? third edition, for new users of the EarthLink network, including such information as how to use email. Framemaker release 5 (for Macintosh). CD-ROM disk, quick reference, Introducing Frame Maker, Installing FrameMaker Inspiration for Macintosh. V. 4.1a Two disks. 1988-1994. Also 4.1c Updater. Kensington Mouseworks QuickStart, plus disk, v. 5.04. MacWorld present Click art disk Norton Utilities v. 4.0, education Now Synchronize. 2 disks. For Palm Pilot and Mac. Now Up-To-Date, and Contact. V. 3.5 for Macintosh. 3 disks. Now Up-to-Date. 1993. (probably later than the other one? Looks more sophisticated) Now Contact, 1993. Ohio Distinctive Software: Executive Diet Helper, Weight Loss Planner, Menu Planner (Macintosh), 1994 Sad macs Utilities, the official companion disk for Ted Landau?s book, Sad Macs, Bombs, and Other Disasters. 1996.

8 years, 3 months

1
0
0 0

Quad density Pertec

by cclist＠sydex.com

On 03/11/2018 08:19 AM, Al Kossow wrote: > I've scrapped six of those already. They aren't worth anything. > > > On 3/11/18 1:23 AM, jim stephens wrote: >> I think this is actually a quad density half inch.? If the guy didn't burn it up (says probably 12v fault) it would be >> handy. >> Isn't that a Kennedy streamer? Sure looks like one. I note that the Kennedy incremental 7 inch reel drive in the NASA flight case hasn't attracted a lot of interest. That sample tape that I got, however does verify that the parity track on this telemetry stuff is unused. So that explains the 8 data inputs with no parity on the NASA model. --Chuck

8 years, 3 months

2
1
0 0

Cray Origin 2000 From Indiana University Scaamp Project- Rescued

by phreakshowtelco＠gmail.com

I won an auction down at Indiana University for an SGI Origin 2000 System and 19 racks. Trip was an adventure. Rented a 26ft Penske Truck which was a junkheap in itself. Off we went. My gf and her best friend went along and had a blast. 7 Hour drive down from Michigan to Bloomington Indiana. In a rainstorm at dark. Waffle House outside of Indianapolis made for a very nice night. Got loaded up 9am yesterday morning. And headed home. Here are pics of the SGIs. And my gf's find an IBM Selectric II. Shes a typewriter lover. https://imgur.com/a/XzDXg Plan now is to start rounding up parts to fix it. It seems mostly cosmetic. Goal is to have it fully operational by VCFMW. I also found some historical info on it too https://www.hpcwire.com/1997/05/16/indiana-u-installs-64-node-origin2000/ Eventually this belongs on display somewhere. I plan to get an inventory of everything this week. and Im looking for any extra parts that anyone has for this. Thanks

8 years, 3 months

5
4
0 0

Replica IBM 5150 PC motherboard

by lproven＠gmail.com

This turned up on Fess Bouc yesterday and it was news to me. It's a DIY replica of an original IBM PC motherboard: http://www.mtmscientific.com/pc-retro.html -- Liam Proven ? Profile: https://about.me/liamproven Email: lproven at cix.co.uk ? Google Mail/Hangouts/Plus: lproven at gmail.com Twitter/Facebook/Flickr: lproven ? Skype/LinkedIn: liamproven UK: +44 7939-087884 ? ?R (+ WhatsApp/Telegram/Signal): +420 702 829 053

8 years, 3 months

13
19
0 0

Last sun3 ask: In search of a SCSI controller (VME) for a 3/260

by ian.finder＠gmail.com

Folks, sorry for the Sun spam. Everything was working in my newly acquired 3/260, and the monitor is even starting to shape up. It was a gorgeous machine until I tried to use the SCSI bus on it. The controller is dead, very dead. No fuses or obvious things. No matter the device or chain... including the original disks. ?getbyte error, phase mismatch? So again I plead- does anyone have a Sun 3 scsi controller, preferably of the internally pinned type, sitting on a shelf somewhere? Thanks, - Ian

8 years, 3 months

3
2
0 0

2 long lost systems Needs OS, Update

by g-wright＠att.net

Date: Fri, 9 Mar 2018 04:53:27 +0000 (UTC) From: Jerry Wright <g-wright at att.net> To: "cctalk at classiccmp.org" <cctalk at classiccmp.org> Subject: 2 long lost systems Needs OS Message-ID: <1082292210.13919302.1520571207779 at mail.yahoo.com> Content-Type: text/plain; charset=UTF-8 Hi All,? I'm still looking for the OS media or any manuals for 2 systems 1 is a OSM Zues 4 Early Z80 System,the other is? a Pertec p4010 mini. which uses coax to the terminals.? I can find a little bit on the Pertec 3200 but nothing on the 4010. Thanks, Jerry ,,,,,,,,,,,,,? Update? ,,,,,,,,, for those that asked and add info The Zues is cute little desk top system with? a wood top. 16x16, Very simple, but nice.Had its own Multi user OS, Z80,? Seagate? ST-212 HD? 12 meg , 5 1/4 Floppy.? With 10 serial? ports, I would guess this thing would be sweating bullets,? if all 10 ports where busy. Of coarse this is 2018 and it still runs. That has to say something.? date code is 1984 ?Pertec After doing a little searching . This is a Pertec 3200 series. By the info I have seen,It is a 3230 floor standing model.? The P4010 on the tag is most likely the configuration ??? It has a 70 meg HD (MFM), Bridge board,Tape drive and? 5 1/4 Floppy. 68020 processor The Coax ports, where fast and The terminals could? be a long distance away. The Bridge board has a 68000 Processor and DPT sticker on the Roms.? Very nicely made Machine. Each Terminal Had a Z-80 with 64k of Memory in it. There is a company in? Denver that lists the OS but they have not returned my E-mail Requests Yet ?? - Jerry I have added some Zues and Pertec? Terminal pictures to this file. https://www.dropbox.com/sh/xsa6xu6fn9ct6db/AAC93v0xdy0nSuOJQ-1ApGbta?dl=0

8 years, 3 months

1
0
0 0

Pertec P4010 pictures, Maybe was 2 long lost Systems needs OS

by g-wright＠att.net

Date: Fri, 9 Mar 2018 04:53:27 +0000 (UTC) From: Jerry Wright <g-wright at att.net> To: "cctalk at classiccmp.org" <cctalk at classiccmp.org> Subject: 2 long lost systems Needs OS Message-ID: <1082292210.13919302.1520571207779 at mail.yahoo.com> Content-Type: text/plain; charset=UTF-8 Hi All,? I still looking for the OS media or any manuals for 2 systems 1 is a OSM Zues 4 Early Z80 System,the other is? a Pertec p4010 mini. which uses coax to the terminals.? I can find a little bit on the Pertec 3200 but nothing on the 4010. Thanks, Jerry Here are a few pictures of the P4010 ?Try this again. Let me know it ti fails - Jerry https://www.dropbox.com/sh/xsa6xu6fn9ct6db/AAC93v0xdy0nSuOJQ-1ApGbta?dl=0

8 years, 3 months

3
2
0 0

Sanyo PHC-3100 (or PHC-3000) ?

by mattislind＠gmail.com

Does anyone have more info on these Japanse machines. I collected the infomation I got from the former owner of a PHC-3100. Interesting machines based on the TMS9900. http://www.datormuseum.se/computers/others/sanyophc3100-1 I have 32 floppies which was dumped using ImageDisk. 40 tracks, double sided, FM encoding. But none of these floppies are original so I am not sure if I have the full OS, whatever that is. I also lack documentation. >From what I understand they were never sold outside Japan.

8 years, 3 months

1
0
0 0

Pertec P4010 computer

by g-wright＠att.net

Date: Fri, 9 Mar 2018 04:53:27 +0000 (UTC) From: Jerry Wright <g-wright at att.net> To: "cctalk at classiccmp.org" <cctalk at classiccmp.org> Subject: 2 long lost systems Needs OS Message-ID: <1082292210.13919302.1520571207779 at mail.yahoo.com> Content-Type: text/plain; charset=UTF-8 Hi All,? I still looking for the OS media or any manuals for 2 systems 1 is a OSM Zues 4 Early Z80 System,the other is? a Pertec p4010 mini. which uses coax to the terminals.? I can find a little bit on the Pertec 3200 but nothing on the 4010. Thanks, Jerry Here is a few pictures, This has? a 68020 processor and a build date of 1989 Pertec_4010.zip - Jerry | | | | | | | | | | | Pertec_4010.zip Shared with Dropbox | | | |

8 years, 3 months

1
0
0 0

2 long lost systems Needs OS

by g-wright＠att.net

Hi All,? I still looking for the OS media or any manuals for 2 systems 1 is a OSM Zues 4 Early Z80 System,the other is? a Pertec p4010 mini. which uses coax to the terminals.? I can find a little bit on the Pertec 3200 but nothing on the 4010. Thanks, Jerry

8 years, 3 months

3
2
0 0

Picked up a couple 386 machines

by lyokoboy0＠gmail.com

While working at the scrapyard today, i managed to get a couple 386 machines right as they were being dropped off. One is a pakard bell with monitor, in pristine condition. The other is a Tandy 2500 with monitor, in rough looking shape but working too. The monitor is pretty beat up for the tandy but working. I have been on the look ut for a good 386 mahine for a while now, i got kinda lucky and picked up two working systems in one day. The pakard bell is up and running fine, it was a pretty standard machine and just needed a hard drive. The tandy 2500 is pretty nice as well, it has a cdrom and a hard drive installed, although the hard drive is dead and seems to only accept AT hard drives. I am still learning about tandy computers, on my other machines, i was unable to find an 8 bit isa cad that could support newer ide drives. On the machine i just picked up it looks like a 16 bit isa slot is free, if i were to install a 16 bit ide hard drive controller for use with newer ide drives, would it work, or cause some kind of conflict with the onboard hard drive controller? The floppy drive is quite dirty but reads disks sometimes, i need to clean it up. Im hoping to post back with a couple pictures of both the machines running. I do not need them both, I really like the packard bell, but if someone absolutely needs a 386 machine with monitor I am open to offers to get one shipped out and keep the other one. --Devin

8 years, 3 months

5
7
0 0

VT52 microprogram

by lars＠nocrew.org

Hello, Does anyone have VT52 microprogram ROM image, a listing, or a copy of "DECscope System Manual"? Best regards, Lars Brinkhoff

8 years, 3 months

2
3
0 0

Hand-crafted beauty pays tribute to the dawn of home computing looks like a PET! but in walnut!

by couryhouse＠aol.com

Hand-crafted beauty pays tribute to the dawn of home computing https://newatlas.com/love-hulten-pet-de-lux/53608/ Ed# www.smecc.org

8 years, 3 months

2
1
0 0

Anyone have the service guide for a Sanyo VM4209 monitor?

by janso96＠hotmail.com

Hi, I'm trying to repair this monitor, but unfortunately I can't find any service manual or guide with schematics for it. I found something on www.electronic-circuitry.com<http://www.electronic-circuitry.com>, but it's impossible to download. Thanks in advance, Janek Sochaczewski

8 years, 3 months

2
4
0 0

Dec-10 Day announcement from Living Computers: Museum + Labs

by RichA＠livingcomputers.org

Happy DEC-10 Day! It is my honor to announce that we at Living Computers: Museum + Labs are releasing to the computing community our Massbus Disk Emulator and all the associated software. This device connects via Massbus cables to the RH10 and RH20 interfaces on KI-10 and KL-10 systems, to the RH11 interface on KS-10 and small PDP-11 systems (including the front end 11/40 on the KL-10), and to the RH70 on the PDP-11/70. The MDE provides up to 8 emulated RP06 or RP07 disks (represented by disk files in the format used by the SimH emulation of these systems). We expect that it will also work with the RH780 on the VAX-11/780 and VAX-11/785 although we have not yet tested it in this configuration. The original MDE was designed by Keith Perez in 2005, and emulated up to four RP06 drives connected to a KL-10. The current generation was a redesign by Bruce Sherry in conjunction with the restoration of our DECsystem-1070 in 2012, and initially provided eight RP06 drives on the RH10. It has undergone continual development, with associated software created for us by Bob Armstrong, and is now being opened up for the use of the relevant communities. To this end, we have placed the design files for the hardware and the source files for the software to interface with it, along with our library of Universal Peripheral Emulator routines, on public access repositories at Github. The URLs for these repositories are https://github.com/livingcomputermuseum/MDE2 https://github.com/livingcomputermuseum/MBS https://github.com/livingcomputermuseum/UPELIB These are released under a very liberal license which will allow for free use of the MDE by any interested party. Happy Dec-10 Day! Rich Richard Alderson, Sr. Systems Engineer Living Computers: Museum + Labs 2245 1st Avenue S Seattle, WA 98134 Cell: (206) 465-2916 Desk: (206) 342-2239 http://www.livingcomputerss.org/

8 years, 3 months

7
6
0 0

AlphaCom Terminal

by billdegnan＠gmail.com

The 1969-71 AlphaCom terminal is a candidate for https://terminals-wiki.org/ Here are some photos http://www.vintagecomputer.net/browse_thread.cfm?id=502 I got this from the inventor's son. I am unsure how many of these were made or put into production. The terminal kind-of worked for a while, it saves forms in core memory and transmits them like a glass teletype (i.e. datapoint 3300) and would have been a competitor machine. Unfortunately it's too complex for me to decipher, there are no schematics and I am unable to get it running again. The Sanyo TV adapted as a display is also dysfunctional now. Perhaps someone here would like to help me make progress. I have a ton of photos on my site, linked from the above thread, but doubtless more research is necessary. I am located in Landenberg, PA USA near Philadelphia due west of Newark Delaware. BIll

8 years, 3 months

1
0
0 0

DEC compatible boards

by useddec＠gmail.com

I have well over 100, maybe 200 DEC compatible boards which I have no plans to use. Maybe 20 or so EMULEX, DILOG, ADAC, DATA TRANSLATIONS, and dozens or other manufacturers. Also the ones that have no company name on them. They range from a few PDP-8 boards, to Q-bus. Unibus, to VAX. I hope to have a complete list sometime later this year, bur feel free to send a wish list (off list)and I will dig through them. Thanks, Paul

8 years, 3 months

2
2
0 0

old TV, radio, hi fi service manuals

by sales＠elecplus.com

I have at LEAST 5 cases of these old Sam's books. Any interest, or dumpster fodder? Mostly Zenith and RCA. Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 3 months

2
1
0 0

Pics of the 3B2 stuff, if anyone is interested.

by sales＠elecplus.com

Like I said, I think Seth is taking these. https://drive.google.com/drive/folders/1kt4K6UMy54kNjzgL-1t_iwXm6RqsfJVJ?usp =sharing Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 3 months

1
0
0 0

3B2 stuff

by sales＠elecplus.com

It is just the manuals. Seth answered me and I am pretty sure he is going to take them. I don't have the 200 pound hardware anymore. Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 3 months

1
0
0 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb