>DON'T EVER GO INSIDE A RUNNING OR RECENTLY POWERED OFF
>MONITOR OR TV WITH A CRT UNLESS YOU KNOW WHAT YOU'RE DOING.
Just how recently would recently be?
That, frankly, is a matter of dispute. The *correct* answer is to know
how to discharge the anode voltage, have the appropriate tools to do so
and to measure the result to confirm success, and to perform the
procedures properly. (Hint: If you don't know how, find somebody who
does.) The service manual from whatever CRT-based device you're messing
with should have proper instructions. And if you don't have the service
manual, what in heck are you doing in there anyway?
Thanks,
Tom
Applefritter
www.applefritter.com
> > I think I managed to hit 100+MPH on a few occasions.
> >
> > WHEEEEEEE!!
>
> I thought all Americans drove at no more than the 50? limit ;-)
Speed limit on most U.S. Interstate highways is 65mph... urban
areas typically mandate a lower speed limit, we have a section
of Interstate locally known as Dead Man's Curve that mandates
a 35mph speed limit for semi tractor-trailer rigs, and another
section called Hospital Curve where the limit is 50mph for both
trucks and cars (and I won't even get into describing our local
section known as Spaghetti Junction).
Montana? and/or North Dakota flirted with no limits outside
ruban areas (actually the law specified that speeds must be
reasonable and prudent for the conditions or something like
that), but they maye have finally done away with that due to
lobbying by insurance company interests.
-dq
--- Jim Arnott <jrasite(a)eoni.com> wrote:
> BTW, a short intro...
>
> I'm Jim Arnott. A former system admin for a LAN using: 11/24s, 11/23s and an
> 11/44. O/S rt11sj, rt11sj and rsx11m+ respectively. All Decnetted together.
> (Coordinate measuring machines talking to the data gatherer.) It's been a
> number of years, but I do remember a bit... Also was hooked to the ibm370
> through RJE-HASP.
Out of curiosity, how did you do the HASP connection? I didn't know
anyone had an RT-11 HASP product. There were several RSX-11 and RSTS
solutions, both from DEC and third parties.
-ethan
=====
Even though my old e-mail address is no longer going to
vanish, please note my new public address: erd(a)iname.com
The original webpage address is still going away. The
permanent home is: http://penguincentral.com/
See http://ohio.voyager.net/ for details.
__________________________________________________
Do You Yahoo!?
Yahoo! Photos - 35mm Quality Prints, Now Get 15 Free!
http://photos.yahoo.com/
Hello everyone, I would like to build a "4:1" box that can switch between
one of four DEC MMJ consoles. This is so my mini-cluster can have one
terminal be the console for four machines. However, I've noticed that
sometimes I get a 'break' sent if I simply unplug and plug, so to prevent
that I want to make a "hold" circuit such that the VAX will continue to
thing a terminal is attached. Any suggestions?
--Chuck
DC = normal data cartridge, whereas I believe the EF = error free. What do
you mean by set? If you mean that its turned red, then I would be less than
enthusiastic about using them, and if I bought them on Ebay or something,
I'd want my money back.
Will J
_________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
Share information about yourself, create your own public profile at
http://profiles.msn.com.
Sounds like a control computer for a GenRad automated pc-board
testing system. They used various pdp11 machines to run their board
testing machines. I'd say it's a pretty nice score.
-Dave McGuire
On September 22, Joe wrote:
> A couple of weeks ago I found a box in a scrap yard with a half height 8"
> floppy drive it in. The box was marked "Gen-Rad" and looked like part of a
> old piece of test equipment. I picked up the box just for the floppy drive
> and brought it home. Today I started to take it apart and found that it was
> made by Scientific Micro Systems and has a number of DEC cards in it as
> well as a Maxtor XT-1085 hard drive. My question is what is it and weather
> it's worth keeping or is it just good for parts?
>
> Here's the details; It's marked "Gen Rad 2295 Central Station" on the
> front. The back is marked "Scientific Micro Systems" "model MDX01170".
> It's about 9" w x 11" h x 17" deep. On the back it has eight DB-25m ports
> on the back. They're marked "TZ0" through "TZ3", "LP0" and "TT0" through
> "TT2". Inside it has a DEC M7957 quad board, a half size board made by
> Sigma Information Systems Inc (connected to the TT* and LP0 ports), a half
> size "Q RAM 11" board made by Clear Point (memory?), a DEC M 8186 half size
> card, and a half size SMS card (1002001-0001/0004220-0001) that is also
> connected via a jumper to the last card, a full quad size SMS card
> (1001939-0001/0003770-0001). The last card has ribbon cables that connect
> to the floppy and hard drive.
>
> Does anyone know what it is? Is it worth anything? FWIW I haven't tried
> to connect a terminal to it yet but it appears to power up and boot.
>
> Joe
If there are any takers, please reply directly to the sender.
Reply-To: DGBJ(a)aol.com
---------- Forwarded message ----------
Date: Sat, 30 Sep 2000 23:34:00 EDT
From: DGBJ(a)aol.com
Subject: IBM XT 286
I have an IBM XT 286 with color monitor, keyboard, two pin printers, manuals
and software to donate to anyone who will make good use of it, preferably a
museum. Email or call me at 371-7745. I live in San Jose, California.
Sellam International Man of Intrigue and Danger
-------------------------------------------------------------------------------
Looking for a six in a pile of nines...
VCF 4.0 is September 30-October 1
San Jose Convention Center, San Jose, California
See http://www.vintage.org for details!