23 May
2012
23 May
'12
4:36 p.m.
I am cleaning out the garage. Found a couple more RA-81 pieces to pass
on. These items are light enough that there is no problem shipping
them. Items are located in the Seattle area.
The drive spindle is about 7" diameter and 6" tall. The platters were
stacked on vertical separators with the spindle in the center. There is
a pleated air filter that goes around the inside, center of the spindle.
The disk enclosure is about 16" wide, 18" long and 7" tall. It held the
platters, spindle and head assembly.
As far as price, make an offer. I really just want to get stuff out of
my garage, but, if someone wants to pay for the stuff that I am getting
rid of, that would be awesome.
For photos, check out this link -
http://www.vintage-computer.com/vcforum/showthread.php?30901-Drive-spindle-…
alan
23 May
23 May
4:40 p.m.
New subject: MF7114 and the CPS/1
Hi I was wondering if anyone had any info or picturesof the CPS/1. I've done some
searches on the web and only found limitedinformation.Dwight
4:45 p.m.
FYI, this is called an "HDA", for "head-disk assembly.
-Dave
On 05/23/2012 04:36 PM, Alan Perry wrote:
I am cleaning out the garage. Found a couple more RA-81 pieces to pass
on. These items are light enough that there is no problem shipping
them. Items are located in the Seattle area.
The drive spindle is about 7" diameter and 6" tall. The platters were
stacked on vertical separators with the spindle in the center. There is
a pleated air filter that goes around the inside, center of the spindle.
The disk enclosure is about 16" wide, 18" long and 7" tall. It held the
platters, spindle and head assembly.
As far as price, make an offer. I really just want to get stuff out of
my garage, but, if someone wants to pay for the stuff that I am getting
rid of, that would be awesome.
For photos, check out this link -
http://www.vintage-computer.com/vcforum/showthread.php?30901-Drive-spindle-…
alan
--
Dave McGuire, AK4HZ
New Kensington, PA
5:01 p.m.
...aaaand I just realized that I read Alan's post too quickly;
apparently he doesn't have the entire sealed HDA.
I'll be crawling back under my rock now. ;)
-Dave (who's looking for an RA81 HDA)
On 05/23/2012 04:45 PM, Dave McGuire wrote:
FYI, this is called an "HDA", for "head-disk assembly.
-Dave
On 05/23/2012 04:36 PM, Alan Perry wrote:
--
Dave McGuire, AK4HZ
New Kensington, PA
I am cleaning out the garage. Found a couple more RA-81 pieces to pass
on. These items are light enough that there is no problem shipping
them. Items are located in the Seattle area.
The drive spindle is about 7" diameter and 6" tall. The platters were
stacked on vertical separators with the spindle in the center. There is
a pleated air filter that goes around the inside, center of the spindle.
The disk enclosure is about 16" wide, 18" long and 7" tall. It held the
platters, spindle and head assembly.
As far as price, make an offer. I really just want to get stuff out of
my garage, but, if someone wants to pay for the stuff that I am getting
rid of, that would be awesome.
For photos, check out this link -
http://www.vintage-computer.com/vcforum/showthread.php?30901-Drive-spindle-…
alan
5:14 p.m.
On Wed, May 23, 2012 at 5:01 PM, Dave McGuire <mcguire at neurotica.com> wrote:
? ? ? ? ?-Dave (who's looking for an RA81 HDA)
I think I have a dead one... I've got at least one working RA81 and a
parts donor. Sometime later this year, I might be in a position to
offer what the OP is offering - I've been watching the thread to see
how much interest it generates.
Of course what one could do is take a gutted RA81 and mount some other
drive inside the empty shell - presuming you could tap into the
original light/switch panel, it wouldn't look bad and would weigh a
lot less.
I'd rather move a rack of those than a "real" SA600...
-ethan
5:30 p.m.
On 05/23/2012 05:14 PM, Ethan Dicks wrote:
Yeah. I'm looking for a live one, or a whole RA81. I have a line on
a whole drive but I can't (yet) afford to have it shipped.
-Dave
(who's looking for an RA81 HDA)
I think I have a dead one... I've got at least one working RA81 and a
parts donor. Sometime later this year, I might be in a position to
offer what the OP is offering - I've been watching the thread to see
how much interest it generates. Of course what one could do is take a gutted RA81 and
mount some other
drive inside the empty shell - presuming you could tap into the
original light/switch panel, it wouldn't look bad and would weigh a
lot less.
Eh.. :-/
I'd rather move a rack of those than a
"real" SA600...
Well, there is that. ;)
-Dave
--
Dave McGuire, AK4HZ
New Kensington, PA
5:16 p.m.
--- On Wed, 5/23/12, Dave McGuire <mcguire at neurotica.com> wrote:
? ...aaaand I just realized that I read Alan's
post too
quickly;
apparently he doesn't have the entire sealed HDA.
? I'll be crawling back under my rock now. ;)
? ? ? ? ? -Dave (who's looking for
an RA81 HDA)
Heh. The RA81 HDA was an often-failed component. I had a deal to buy two racks of
RA81's several years ago from a surplus computer dealer - and when I went to go take a
look at them, it was painfully obvious that every one of them was missing the HDA. Just
the motor and the boards/PSU were in the boxes, the entire HDA was missing. Apparently
they must have sold off the HDA's a long time ago.
-Ian
6:54 p.m.
As I dig through the stuff in the garage, I'm finding some documentation gems.
I located a TEK 4010 service manual, checking on bitsavers shows only
the users manuals.
Is this something common?
Jim.
On 5/23/12, William Donzelli <wdonzelli at gmail.com> wrote:
Heh. The RA81
HDA was an often-failed component.
A bad design, apparently, with a bearing that is just too wimpy.
Does anyone here have an RA81 that works? In somewhat regular use?
--
Will
24 May
24 May
9:15 a.m.
Does anyone here have an RA81 that works? In somewhat
regular use?
Four of them (assuming you'll count RA82s as well). My biggest concern
is that the heads are only good for so many takeoff/landing cycles, so it's
best to leave the drives spinning 24x7. As you've said, the HDAs are the
most common failure - the rest of the drive is pretty reliable.
BTW, I'd love to find a working HDA for an RA80 (not 81 or 82) to make my
730 "like new" again.
Bob
25 May
25 May
3:17 p.m.
New subject: any working : RA-81 drives
I still have a working RA- 80 and new in the box spare HDS's for it.
If that counts
- Jerry
----- Original Message ----
From: William Donzelli <wdonzelli at gmail.com>
To: General Discussion: On-Topic and Off-Topic Posts <cctalk at classiccmp.org>
Sent: Wed, May 23, 2012 3:08:01 PM
Subject: Re: FS: RA-81 drive spindle and disk enclosure
Heh. The RA81 HDA was an often-failed component.
A bad design, apparently, with a bearing that is just too wimpy.
Does anyone here have an RA81 that works? In somewhat regular use?
--
Will
4441
days inactive
4443
days old
10 comments
9 participants
participants (9)
-
alanp＠snowmoose.com -
bob＠jfcl.com -
dkelvey＠hotmail.com -
ethan.dicks＠gmail.com -
g-wright＠att.net -
ian_primus＠yahoo.com -
jim.p.davis＠gmail.com -
mcguire＠neurotica.com -
wdonzelli＠gmail.com