- test-drb@ccmp.vtda.org - classiccmp.org

by pete＠dunnington.u-net.com

On Dec 2 2004, 10:43, Paul Koning wrote: > >>>>> "David" == David Betz <dbetz(a)xlisper.mv.com> writes: > > David> ...and then > > David> COPY/BOOT DY1:RT11FB.SYS DY1: > > David> Unfortunately, that doesn't result in a bootable disk. > David> .... It's just that I can't boot > David> the disk after the second COPY/BOOT step. > > I believe the OS image you want to boot HAS to be called MONITR.SYS on > the bootable disk. Only in really ancient versions of RT-11; not in V5. David's problem may have been that the RT11FB.SYS was SYSGENed inappropriately. The COPY/BOOT copies a section of the monitor into block 0 of the disk. -- Pete Peter Turnbull Network Manager University of York

21 years, 4 months

1
0
0 0

Scortched Earth (was: Re: Sale of "free" stuff on eBay)

by woyciesjes＠sbcglobal.net

Tom Jennings wrote: >>that, a letter from a lawyer is often effective. > > > To what end, this? It's a bit scorched-earth don't you think? > Hmmm, that rings a bell. I remember playing a DOS game by that name. Up 10 players, each has a tank in a 2-D screen, and you can blow the snot out of (or from under) each other. Anybody else play that game? -- --- Dave Woyciesjes --- ICQ# 905818

21 years, 4 months

4
5
0 0

"SPARC workstation Model 51 on eBay

by jpl15＠panix.com

No really sure that this is what it says it is - looks kinda military to me... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=4193&item=5143935062… Anyway, interested parties are referred thereto. Cheers John

21 years, 4 months

1
0
0 0

RT-11 installation

by trash3＠splab.cas.neu.edu

The RX01 used the DX driver and the RX01 used the DY driver. If the driver on the floppy does not match the actual drive, it will not boot. So, a normal RX01 floppy will not boot in an RX02 drive and vice versa. However, I THINK that if you used the wrong density floppy but put the right driver on it (An RX01 floppy with the DY driver as the boot driver) it will work, but that is not how the distributions were set up. Of course there are games you can play, like toggling in a bootstrap, but I don't think that was being asked. Well, anyway, that is what I remember of it, please, anyone, correct me if I'm wrong. Joe Heck

21 years, 4 months

1
0
0 0

Jeffrey Worley (technoid)

by wayne.smith＠charter.net

-----Original Message----- From: Wayne Smith [mailto:wayne.smith@charter.net] Sent: Wednesday, December 01, 2004 8:59 PM To: 'cctalk(a)classiccmp.org' Subject: Re: Jeffrey Worley (technoid) > Date: Wed, 1 Dec 2004 07:55:35 -0800 > From: "Zane H. Healy" <healyzh(a)aracnet.com> > Subject: Re: Jeffrey Worley (technoid) > To: "General Discussion: On-Topic and Off-Topic Posts" > <cctalk(a)classiccmp.org> > Message-ID: <a06200700bdd3991d05ee(a)[192.168.1.199]> > Content-Type: text/plain; charset="us-ascii" ; format="flowed" > > >SSN: xxx-xx-xxxx > > Even if he is in Jail for Murder, posting that little tidbit of > information to the List is totally inappropriate. If that info is > publicly accessible on a Florida website then there is a problem > there as well. > > Zane > There is likely another reason that SSN's for convicted felons are available, and that is to, as they say, "protect the innocent." Lots of people have names that are common with other people, and these databases are largely used by employers to do background checks on potential employees. Providing the SSN greatly reduces the risk of a false positive that could result if you only ran a search by name - in other words, if the SSN doesn't match, it isn't the same person. As some may recall, when Schwarzenegger was campaigning for governor in CA there was a woman who accused him of groping who was immediately identified by the Schwarzenegger campaign as having been previously convicted for prostitution. Turned out that the hooker was a different woman with the same name. All they needed were a couple of SSNs. -W

21 years, 4 months

1
0
0 0

HP 2748B paper tape reader (ebay)

by jwest＠classiccmp.org

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=1247&item=5144629838… If you could pick one... just ONE peripheral to put on an HP 2100 or 21MX, this would be it. He's including the cable and interface card too. Note, the cable will need a little work :) Jay

21 years, 4 months

1
0
0 0

In NZ

by ethan.dicks＠gmail.com

OK, all... After 57 weeks... I have escaped the South Pole and am spending some wonderful warm sunny days in Christchurch, NZ. Should be here for a few weeks, so if any Kiwis on this list would like to have a get-together, let me know by e-mail, and I'll pass on my mobile number (which I'll be getting in an hour or so when I pick up a sim card for a borrowed phone). I have plans to visit the North Island later this month, but for a few weeks, I'll be here, hanging out. Cheers, -ethan P.S.- for another week or so, I'll have my Elf and SBC-6120 with me before I consider mailing them home... if you want to see one... there's a brief window of opportunity. I have a week left of U.S. postal priveleges with the program.

21 years, 4 months

1
0
0 0

BYTEK 135 Help

by jrkeys＠concentric.net

Anyone have the manual for a BYTEK 135 Multiprogrammer model 135-U/A

21 years, 4 months

1
0
0 0

Approaches to projects

by dwight.elvey＠amd.com

>From: "Ethan Dicks" <dickset(a)amanda.spole.gov> > >On Thu, Nov 25, 2004 at 01:26:04AM +0000, Philip Pemberton wrote: >> In message <200411250057.QAA03125(a)clulw009.amd.com> >> Aside from being a "better KIM"? ISTR it was basically a KIM with a few >> extras (oscilloscope output, a la the Poptronics Scopewriter) added. I don't >> think it used the mask-programmed RIOT chips either, unlike the KIM, which >> makes it (slightly) easier to fix if something goes wrong. > >It does not use mask-programmed RIOT chips... one of the reasons I'm happy >to have a SYM-1 - no unobtanium ingredients. > >-ethan Hi Ethan One can wire the 6532 and EPROM chip in place of the 6530. It does require a little mapping because the selects most likely won't be compatable but the rest should work. There is a fellow in France that is doing this for Pinball machines. Dwight

21 years, 4 months

2
1
0 0

AIM thermal printer

by rcini＠optonline.net

If someone needs this, they should grab it: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=5142464129&ssPageName=ADM E:B:SS:US:1 Rich Rich Cini Collector of classic computers Build Master for the Altair32 Emulation Project Web site: http://highgate.comm.sfu.ca/~rcini/classiccmp/ /************************************************************/

21 years, 4 months

2
2
0 0

Finding shorts in boards

by pete＠dunnington.u-net.com

On Dec 1 2004, 13:21, Jules Richardson wrote: > > I've got a board here with a short between ground and the +5V rail > (actually not quite dead - I'm getting around 10 ohms between the rails) > > Any useful tips for finding the fault? It's a large board, multi-layer, > lots of silicon on it unfortunately :-( That's only about 500mA at 5V. Sure it's a short? Of course, it may draw lots more than that under power, if your meter is not using enough voltage to turn on junctions. > Are there any particular components that are likely to fail in this way > that might be found across PSU rails? (decoupling caps, certain ICs, > crystal modules etc.?) Decoupling caps, TTL, and some MOS memory chips all can draw excess current when faulty. I usually put them on a hefty 5V supply and feel for what's hot (you can sometimes burn out the short in a decoupling cap that way -- they often go bang). Point of reference: a BBC B board normally draws about 2A at 5V, but the last one I had with a particularly nasty set of faults drew over 10A at 5V -- and the faulty TTL chips got hot enough to feel without actually touching them. > Given a suitably sensitive meter is it sensible to assume I can try and > home in on the short location a little? (I've found readings between > GND/supply on various LS chips of anything between 9.5 and 12 ohms so > far) You really want a current tracer. HP made a really nice one, and I'm still annoyed I didn't bid high enough on the last one I saw :-( -- Pete Peter Turnbull Network Manager University of York

21 years, 4 months

2
1
0 0

Finding shorts in boards

by melamy＠earthlink.net

the biggest culprit when it comes to older electronics is the good old tantalum cap. I have seen these be a little resistive, dead shorts, etc. good luck. best regards, Steve Thatcher At 08:21 AM 12/01/2004, you wrote: >I've got a board here with a short between ground and the +5V rail >(actually not quite dead - I'm getting around 10 ohms between the rails) > >Any useful tips for finding the fault? It's a large board, multi-layer, >lots of silicon on it unfortunately :-( > >Are there any particular components that are likely to fail in this way >that might be found across PSU rails? (decoupling caps, certain ICs, >crystal modules etc.?) > >Given a suitably sensitive meter is it sensible to assume I can try and >home in on the short location a little? (I've found readings between >GND/supply on various LS chips of anything between 9.5 and 12 ohms so >far) > >I've checked the board for particles of anything that might be causing >the problem, plus I'm halfway through ruling out any of the socketed >ICs. Of course if it's a problem with the multi-layer PCB itself... eek! >(do these ever fail in such a way though? It's a commercial board which >used to be fine) > >cheers > >Jules

21 years, 4 months

2
1
0 0

cctalk Digest, Vol 16, Issue 2

by dwight.elvey＠amd.com

>From: CRC <technobug(a)comcast.net> > > >On 1 Dec 2004 09:43:56, Paul Koning <pkoning(a)equallogic.com> commented: > >>>>>>> "Jules" == Jules Richardson <julesrichardsonuk(a)yahoo.co.uk> >>>>>>> writes: >> >> Jules> I've got a board here with a short between ground and the +5V >> Jules> rail (actually not quite dead - I'm getting around 10 ohms >> Jules> between the rails) >> >> Jules> Any useful tips for finding the fault? It's a large board, >> Jules> multi-layer, lots of silicon on it unfortunately :-( >> >> 10 ohms means about 0.5 amps -- sounds like a perfectly respectable >> amount of current for a board with "lots of silicon" to draw. >> So... are you sure there is a short, rather than just circuitry? >> >> paul > >Unless there are passives (like terminators) between +5V and GND, 10 >ohms is a little low. 0.5 amps represents a minimum current that the >board will pull. An ohmmeter will not normally cause the silicon to >conduct and hence be counted in the total resistance. Some chips do >have internal dividers, but the they are nomally in the 10K + range. > >I normally use a current limited supply at the required voltage and set >the limit so that it starts to limit. I then use a 5 digit voltmeter to >trace where the current is going. This is done by placing one probe on >the +5V input and then measuring the drop as you trace out the >distribution path. The path drawing the current will continually drop >while non-drawing paths will remain at a constant voltage drop. > >On multi-layer boards you measure drops to the Vcc pins of the bugs and >map the drop. > > CRC > > Hi I use a slightly different method. I use a current limiting supply and set it to about an amp or two. I place the supply across one of the power planes ( corner to corner on a solid plane and end to end for E traces ). I do not place the supply form power to ground, just across the one plane. I then place one lead, of a meter that reads 5 digits on a 200 mV scale, from the opposite rail that is shorted two. One then simply traces for a null on the plane with the current flow across it. On a plane, I take a piece of string to mark the line of the null and then put the supply on 90 degrees, across the same plane. Where the new null line cross the old string is the where the short is. This method will even work if the short is +1K, if that is the only current flow. I once showed using it on a burnin board with a 10K resistor that was in wrong out of some 400 sockets and about 12 resistors per socket. I was able to zero right into the exact resistor. The principle is that one uses the plane as though it were a variable resistor and the short was the contact. If one measures along the resistor to the contact, the voltage will be zero at the location where the contact is made. This is much easier to read than CRC's method since you are looking for a null, rather than a stop in the change of the voltage. It also has the advantage that it won't blow an intermittent short so you can find it. It is more sensitive than the HP current probe for power planes ( having used both methods ). It also is run at a very low voltage so there is no chance of damaging other parts. I publish this method every now and then but most people don't think about how it works and will tend to forget it. Such is! Dwight

21 years, 4 months

1
0
0 0

OT: good CS textbooks for a DIYer

by rcini＠optonline.net

Hello, all: I'm looking for recommendations on CS textbooks for myself...I'm embarking on sort of a DIY CS degree :-) Anyway, if anyone could recommend decent first-year and/or second-year books on algorithyms and data structures in C/C++, I would appreciate it. Thanks. Rich Rich Cini Collector of classic computers Build Master for the Altair32 Emulation Project Web site: http://highgate.comm.sfu.ca/~rcini/classiccmp/ /************************************************************/

21 years, 4 months

5
4
0 0

cctalk Digest, Vol 16, Issue 2

by technobug＠comcast.net

On 1 Dec 2004 09:43:56, Paul Koning <pkoning(a)equallogic.com> commented: >>>>>> "Jules" == Jules Richardson <julesrichardsonuk(a)yahoo.co.uk> >>>>>> writes: > > Jules> I've got a board here with a short between ground and the +5V > Jules> rail (actually not quite dead - I'm getting around 10 ohms > Jules> between the rails) > > Jules> Any useful tips for finding the fault? It's a large board, > Jules> multi-layer, lots of silicon on it unfortunately :-( > > 10 ohms means about 0.5 amps -- sounds like a perfectly respectable > amount of current for a board with "lots of silicon" to draw. > So... are you sure there is a short, rather than just circuitry? > > paul Unless there are passives (like terminators) between +5V and GND, 10 ohms is a little low. 0.5 amps represents a minimum current that the board will pull. An ohmmeter will not normally cause the silicon to conduct and hence be counted in the total resistance. Some chips do have internal dividers, but the they are nomally in the 10K + range. I normally use a current limited supply at the required voltage and set the limit so that it starts to limit. I then use a 5 digit voltmeter to trace where the current is going. This is done by placing one probe on the +5V input and then measuring the drop as you trace out the distribution path. The path drawing the current will continually drop while non-drawing paths will remain at a constant voltage drop. On multi-layer boards you measure drops to the Vcc pins of the bugs and map the drop. CRC

21 years, 4 months

1
0
0 0

ot: getting a "coff"

by ron.hudson＠sbcglobal.net

Several of the programs I try to run on my "classic dos" machine give the error message: <filepath\filename>:not coff (check for viruses) I don't yet have a virus scanner, but these files were downloaded from trusted sources I don't think I have a virus. What is this error message?

21 years, 4 months

4
4
0 0

IBM Composer

by vcf＠siconic.com

A nice site on the IBM Composer: http://www.ibmcomposer.org/ -- Sellam Ismail Vintage Computer Festival ------------------------------------------------------------------------------ International Man of Intrigue and Danger http://www.vintage.org [ Old computing resources for business || Buy/Sell/Trade Vintage Computers ] [ and academia at www.VintageTech.com || at http://marketplace.vintage.org ]

21 years, 4 months

1
0
0 0

Jeffrey Worley (technoid)

by wayne.smith＠charter.net

In case anyone wondered what became of him . . . very sad. FLORIDA CRIMINAL HISTORY RECORDS DEPARTMENT OF CORRECTIONS Name: WORLEY, JEFFREY S Status: active inmate Date of Birth: 6/12/1970 Birth State: UT SSN: 528-56-7309 Gender: Male Height (Ft-In): 5'6" Race: WHITE Eye Color: HAZEL *****OFFENSE RECORD***** Comments: PAROLE INELIGIBLE Offense: 2ND DEG MUR, DANGEROUS ACT Offense Severity: Felony Offense Date: 4/26/2003 County or Jurisdiction: DADE Case Disposition: ADJUDICATED Case Number: 0311800 Sentence Date: 3/23/2004 Sentence Type: Custody Sentence Length: 018 YR(S) *****INCARCERATION RECORD***** RECORD 0001 Status: Active Incarceration Date: 4/12/2004 Location: DADE C.I. Sentence Length: 006570 DAY(S) Tentative Release Date: 4/9/2021

21 years, 4 months

10
9
0 0

cctalk Digest, Vol 15, Issue 52

by dwight.elvey＠amd.com

Hi Wayne Sorry for accusing you of missing me. It was a great show this year. I always enjoy these very much. I hope to have a bigger and flashier exhibit next year. My spare time has been somewhat limited this year. Dwight >From: "Wayne Smith" <wayne.smith(a)charter.net> > >> >From: "Wayne Smith" <wayne.smith(a)charter.net> >> > >> >I have posted a few pictures taken during VCF 7.0 at >> >http://webpages.charter.net/jpepperman/VCF%207.0.html. >> > >> >-W >> > >> >> Hi >> Of course my exhibit wasn't even noticed or photographed. >> As usual Sellam gave me half a table and most just figured >> that I was part of the exhibit next to me ( North Star ). >> Since my machine was also a woodie, ( much rarer than >> a North star ) it just blend into the background. >> Maybe next year I'll be noticed. >> Dwight > >Dwight: > >Talk about shooting the "poster". > >Your memory is failing you! :-) Not only did I "notice" your exhibit, I >actually talked to you about it and even photographed it - how could I >have possibly missed it given the very prominent placement assigned by >Sellam! In fact, as I discussed with you, I was at the session when Jim >Willing smoked it (popped the tantalums) at VCF 4. Indeed, at that >session Jim Willing borrowed a BNC to RCA connector from me (that I was >using with my IBM 5100) to put what turned out to be garbage composite >video up on a screen. > >I just went back through the raw photos I took and I saw that the photo >I took of yours turned out very dark, which is why I left it out the >first time around. I will do what I can with Photoshop and add it to >what I posted - give me 1/2 hour. > >Mea culpa, > >-W > > > >

21 years, 4 months

1
0
0 0

ot: getting a "coff"

by RMeenaks＠OLF.COM

Apparently coming from djgpp: http://www.ludd.luth.se/~ams/djgpp/cvs/djgpp/src/stub/stub.asm Ram -----Original Message----- From: Ron Hudson [mailto:ron.hudson@sbcglobal.net] Sent: Wednesday, December 01, 2004 11:54 AM To: General Discussion: On-Topic and Off-Topic Posts Subject: Re: ot: getting a "coff" On Dec 1, 2004, at 8:34 AM, Bert Thomas wrote: > > > Ron Hudson wrote: >> >> Several of the programs I try to run on my "classic dos" machine give >> the error message: >> >> <filepath\filename>:not coff (check for viruses) >> >> I don't yet have a virus scanner, but these files were downloaded >> from trusted sources I don't think I have a virus. What is this error >> message? > > http://www.webopedia.com/TERM/C/coff.html Thanks, I saw that. It only defines COFF. No hints as to what I need to make DOS 6.22 run the thing. One of the instances I where I got this was I was trying "Seal" a GUI written by the people who also put out freeDOS http://www.freedos.org/ And it says at the seal download site that it runs under other DOSses > > (Just googled, not from experience) > (c) 2004 OpenLink Financial Copyright in this message and any attachments remains with us. It is confidential and may be legally privileged. If this message is not intended for you it must not be read, copied or used by you or disclosed to anyone else. Please advise the sender immediately if you have received this message in error. Although this message and any attachments are believed to be free of any virus or other defect that might affect any computer system into which it is received and opened, it is the responsibility of the recipient to ensure that it is virus free and no responsibility is accepted by Open Link Financial, Inc. for any loss or damage in any way arising from its use.

21 years, 4 months

2
1
0 0

Finding shorts in boards

by julesrichardsonuk＠yahoo.co.uk

I've got a board here with a short between ground and the +5V rail (actually not quite dead - I'm getting around 10 ohms between the rails) Any useful tips for finding the fault? It's a large board, multi-layer, lots of silicon on it unfortunately :-( Are there any particular components that are likely to fail in this way that might be found across PSU rails? (decoupling caps, certain ICs, crystal modules etc.?) Given a suitably sensitive meter is it sensible to assume I can try and home in on the short location a little? (I've found readings between GND/supply on various LS chips of anything between 9.5 and 12 ohms so far) I've checked the board for particles of anything that might be causing the problem, plus I'm halfway through ruling out any of the socketed ICs. Of course if it's a problem with the multi-layer PCB itself... eek! (do these ever fail in such a way though? It's a commercial board which used to be fine) cheers Jules

21 years, 4 months

6
6
0 0

SANG megalink transputer board on ebay...

by RMeenaks＠OLF.COM

Here is something you typically wont find easily: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=164&item=5143508523&r d=1 You can use this on an AMIGA if you have the corresponding ZORRO link adapter card... Cheers, Ram (c) 2004 OpenLink Financial Copyright in this message and any attachments remains with us. It is confidential and may be legally privileged. If this message is not intended for you it must not be read, copied or used by you or disclosed to anyone else. Please advise the sender immediately if you have received this message in error. Although this message and any attachments are believed to be free of any virus or other defect that might affect any computer system into which it is received and opened, it is the responsibility of the recipient to ensure that it is virus free and no responsibility is accepted by Open Link Financial, Inc. for any loss or damage in any way arising from its use.

21 years, 4 months

1
0
0 0

A couple of freebies...

by auringer＠tds.net

While cleaning the past weekend, I came across a couple of things that I thought I would try to find a home for. 1) Manual for a Aydin Controls "Slow Scan Analog Patriot Series High Resolution Color Monitor", March 1985. I also happen to have a model 8831 monitor, which is covered in the manual. I do not know the working condition of the monitor, but the cosmetic condition is O.K. The manual contains schematics and troubleshooting information, so I would think making the tube work should be possible. The tube is big, and needs to be picked up on the east side of Madison, WI. 2) 1985 Sharper Image catalog. The only thing I thought was interesting was the ad for an Omnibot 2000 robot. Anyone interested for the cost of shipping? Jon

21 years, 4 months

1
0
0 0

FW: Upcoming Trip...

by dvcorbin＠optonline.net

On Friday 12/3 I will be heading down I-95 from NY to Va. to pick up a great find...Returning Saturday (or possibly Sunday). I will have an SUV with Trailer. If this can be of use to anyone (especially those looking to get rid of DEC equipment to a good home <grin>) drop me a post. Seriouly, anyone on list into DEC (especially PDP-8) who is near this route, drop me a note.... David david(a)dynamicconcepts.us

21 years, 4 months

2
2
0 0

VCF 7.0 Pictures

by wayne.smith＠charter.net

> >From: "Wayne Smith" <wayne.smith(a)charter.net> > > > >I have posted a few pictures taken during VCF 7.0 at > >http://webpages.charter.net/jpepperman/VCF%207.0.html. > > > >-W > > > > Hi > Of course my exhibit wasn't even noticed or photographed. > As usual Sellam gave me half a table and most just figured > at I was > part of the exhibit next to me ( North Star ). Since my machine was > also a woodie, ( much rarer than a North star ) it just > end into the > background. Maybe next year I'll be noticed. > Dwight > > Dwight: Talk about shooting the "poster". Your memory is failing you! :-) Not only did I "notice" your exhibit, I actually talked to you about it and even photographed it - how could I have possibly missed it given the very prominent placement assigned by Sellam! In fact, as I discussed with you, I was at the session when Jim Willing smoked it (popped the tantalums) at VCF 4. Indeed, at that session Jim Willing borrowed a BNC to RCA connector from me (that I was using with my IBM 5100) to put what turned out to be garbage composite video up on a screen. I just went back through the raw photos I took and I saw that the photo I took of yours turned out very dark, which is why I left it out the first time around. I will do what I can with Photoshop and add it to what I posted - give me 1/2 hour. Mea culpa, -W

21 years, 4 months

1
0
0 0

ibm5360

by jimbauer77＠hotmail.com

i my name is jimmy i have ibm 5360 looking for sell if interesse send my email

21 years, 4 months

1
0
0 0

cctalk Digest, Vol 15, Issue 52

by wayne.smith＠charter.net

> >From: "Wayne Smith" <wayne.smith(a)charter.net> > > > >I have posted a few pictures taken during VCF 7.0 at > >http://webpages.charter.net/jpepperman/VCF%207.0.html. > > > >-W > > > > Hi > Of course my exhibit wasn't even noticed or photographed. > As usual Sellam gave me half a table and most just figured > that I was part of the exhibit next to me ( North Star ). > Since my machine was also a woodie, ( much rarer than > a North star ) it just blend into the background. > Maybe next year I'll be noticed. > Dwight Dwight: Talk about shooting the "poster". Your memory is failing you! :-) Not only did I "notice" your exhibit, I actually talked to you about it and even photographed it - how could I have possibly missed it given the very prominent placement assigned by Sellam! In fact, as I discussed with you, I was at the session when Jim Willing smoked it (popped the tantalums) at VCF 4. Indeed, at that session Jim Willing borrowed a BNC to RCA connector from me (that I was using with my IBM 5100) to put what turned out to be garbage composite video up on a screen. I just went back through the raw photos I took and I saw that the photo I took of yours turned out very dark, which is why I left it out the first time around. I will do what I can with Photoshop and add it to what I posted - give me 1/2 hour. Mea culpa, -W

21 years, 4 months

1
0
0 0

Burroughs Panaplex display data needed

by tomj＠wps.com

I recently acquired a virgin Burroughs Panaplex display, and can't find data for it. It's a 24-line, 40-column display, tube only. Character matrixes are 5w x 9h (!) so it'll do decenders. The only markings are a simple "N-0008" on one edge. It's got double staggered rows of pins on all four sides. The whole thing is about 8" x 10". I know how (on paper) to drive panaplex displays (it's nasty) and would love to work up a nice display with this thing if I can find pinout data. Any ideas?

21 years, 4 months

2
2
0 0

Visual 1050 - can anybody send me a photo?

by Shed＠shedward.com

Hi, Did you ever find your photo? Shedward

21 years, 4 months

1
0
0 0

Rescue a 6000! ... & other DEC

by trash3＠splab.cas.neu.edu

Sorry, John, I would have helped, but we leave for vacation this Friday for 16 days. Earlier or later would have been good, but thats the way it is... Joe Heck

21 years, 4 months

2
1
0 0

Interesting Item

by dwight.elvey＠amd.com

Hi I was looking at things on ebay and found item #5144198694. Does anyone recognize this thing. Is it in fact a computer or part of a guidence control? Dwight

21 years, 4 months

3
3
0 0

TV ALERT !!

by news＠computercollector.com

The Travel Channel is showing on segment about Burroughs, on John Ratzenburger's "Made in America" series. It starts at 9:00 EST -- that's in 15 minutes. Evan ===== Tell your friends about the Computer Collector Newsletter! -- It's free and we'll never send spam or share your email address -- Publishing every Monday(-ish), ask about writing for us -- Mainframes to videogames, hardware and software, we cover it all Visit our web site for lots of extra content: http://news.computercollector.com Contact us at news(a)computercollector.com 600 readers and counting!

21 years, 4 months

2
1
0 0

Is agcarrick on the list?

by jrkeys＠concentric.net

I lost out to "agcarrick" for the Sys/36 on ebay today.

21 years, 4 months

1
0
0 0

ZX81 denigrated! (was Re: Approaches to projects)

by pete＠dunnington.u-net.com

On Nov 30 2004, 0:49, Tony Duell wrote: > When I make the adapter I'll add a 3 position switch to it (the adapter), > postiions being 'Always on'. 'Always off', 'Controlled by the remote > cable). One of my Tandy cassette recorders, designed for home computer > use, has such a switch, and it's useful. I made a new DIN plug with the power lead entering via the side, and a 2.5mm jack socket on the end to control the motor. When the 2.5mm plug isn't fitted, the motor is on. No idea about the IEC plug/socket with flat pins, though. > > I had to replace the drive belt in mine a few years back. I got a belt > > from CPC for a few pence. > > There are 2 belts in mine. The large one (which has completely died) > which goes between the motot, capstan flywheel and reel drive pulley, and > a little one in the reel drive mechanism. I was going to change both. I > don't suppose you've got the CPC number for the belt you used, the CPC > catalogue is almost impossible to obtain... Hmm... I vaguely recall two belts as well, but I don't have a record of the part numbers. -- Pete Peter Turnbull Network Manager University of York

21 years, 4 months

2
1
0 0

Multibus pinouts

by julesrichardsonuk＠yahoo.co.uk

Have any of you got Multibus pinouts online anywhere? ta! :) Jules

21 years, 4 months

2
1
0 0

Rescue a 6000! ... & other DEC

by allain＠panix.com

FYI: also there: 2 LP27 lineprinters, 1 TU81-plus tapedrive I was able to swing by Bob Donovan's company on the way to a family function and took a few pictures of the VAX 6000. He talked a bit about apparently three other parties trying to take the machine and giving up. the machine is weeks away from the scrapper. I will be going by in about a week in a normal hatchback car to pick-up what I can. Since the *entire* interior of the car, seats included, is about the size of the VAX, I will dismantle it to accomodate. Alright Jokesters, that's the VAX, not the car. This means that the other 1/2 of the machine is likely going to be scrapped, even though it is in better shape than my car. Just to let you know. If there is another thing I can do, let me know. It's a 6100. quick photos of the visit at http://www.panix.com/~allain/V6000/ John A. Thanks to Bob.D and Rich.B ----- Original Message ----- >From: Gene Buckle <geneb(a)deltasoft.com> >Sent: Thursday, October 14, 2004 12:52 PM >The shipping charges from Conneticut were too rich for my blood so I'm >hoping one of you will be able to save this machine.

21 years, 4 months

1
0
0 0

Multibus pinouts

by aek＠spies.com

http://www.bitsavers.org/pdf/intel/_busSpec/P796_multibusSpec_Oct80.pdf

21 years, 4 months

1
0
0 0

NECS (New England Computer Society) apparently defunct

by tomj＠wps.com

Just for the hell of it I googled the club I hung out with in the late 1970's or early 1980's, NECS. According to one reference (Springfield Mass. Library) their website was www.necs.org, which is now owned by one of those horrid 'buy this site' parasites. I can't even remember anyone's name! What a shame. Used to meet out near 128, meet then go to some local late-night restaurant. The club ran a BBS, ("NECS"...), how I got in touch with them in the first place.

21 years, 4 months

3
4
0 0

MSDos on a dial up ISP?

by msokolov＠ivan.Harhan.ORG

Ron Hudson <ron.hudson(a)sbcglobal.net> wrote: > Subject: MSDos on a dial up ISP? > How do you do that? Take a look at CWRU-PC/IP: ifctfvax.Harhan.ORG:/pub/micro/msdos/net/ For dial-up you'll also need a Class1-emulating packet driver for your SLIP or PPP. Ask your ISP if they could perhaps set you up with SLIP instead of PPP as it's much less painful under DOS. MS, who has connected to Inet from DOS in this manner prior to starting Harhan in 2000.

21 years, 4 months

2
1
0 0

VCF 7.0 Pictures

by dwight.elvey＠amd.com

>From: "Jules Richardson" <julesrichardsonuk(a)yahoo.co.uk> > >On Mon, 2004-11-29 at 17:27 -0800, Vintage Computer Festival wrote: >> On Mon, 29 Nov 2004, Dwight K. Elvey wrote: >> >> > Of course my exhibit wasn't even noticed or photographed. >> >> Well, *I* noticed you, and *I* photographed you (my gallery is still in >> the making). >> >> > As usual Sellam gave me half a table and most just figured >> >> You get what you ask for! If you want more space next year then all you >> need to do is just ask ;) > >Heh, we found that with the CGE show (first show we'd done) - we were >allocated five tables and thought we'd have trouble filling them, and in >the end we needed seven. > >Main lesson learned for next year's show is that you can never have >enough display material to go on the big screens behind the tables, we >were somewhat lacking this time around (and of course anything put up >there needs to be big as the public end up a fair distance away from it) > >Oh, and keep a roll of tape handy to prop the case of your Domesday >system open when it starts overheating ;) > >Definitely need to get Spacewar up and running for next year's show... > >cheers > >Jules > Hi In Sellam's defence, I did only ask for half a table ( although, I only got 1/3 because of overflow ). My exhibit was small enough that it really didn't need more. I was there for the fun and I enjoyed it very much, as I'm sure Sellam knows. The erector set analog computer was fantastic. The PDP11 setup was great as well. I got to actually touch a Curta calculator :) More to my passion, I got a pile of Polymorphic disk from Marvin Johnston to archive. Really great stuff like the original files for the manuals and such. Thanks Sellam! Later Dwight

21 years, 4 months

1
0
0 0

Microway Quadputer/Videoputer transputer setup info needed....

by RMeenaks＠OLF.COM

Hi, I am looking for setup information for the videoputer/quadputer transputer boards from Microway. Does anyone have the manuals? A scan of the docs with the jumpers, settings, etc would be helpful. I am trying to help out a fellow transputer user.... Thanks, Ram (c) 2004 OpenLink Financial Copyright in this message and any attachments remains with us. It is confidential and may be legally privileged. If this message is not intended for you it must not be read, copied or used by you or disclosed to anyone else. Please advise the sender immediately if you have received this message in error. Although this message and any attachments are believed to be free of any virus or other defect that might affect any computer system into which it is received and opened, it is the responsibility of the recipient to ensure that it is virus free and no responsibility is accepted by Open Link Financial, Inc. for any loss or damage in any way arising from its use.

21 years, 4 months

1
0
0 0

Ancient Graphics tablet

by peterdexter＠tiscali.co.uk

Hi I just noticed your reply to a post at http://www.classiccmp.org/pipermail/cctalk/2003-July/025586.html I have just been given an old (1989) Numonics Graphics tablet. It is boxed and never used. I was wondering if you may have any advice or info on this tablet and if it is possible by any means to get this item up and running under any windows platfortm. I guess it is a long shot but I would be interested and grateful if you had any futher knoweldge on this issue. I can connect the tablet to my comp via the cable that shipped with the tablet but that is as far as I can get. Thanks Peter Dexter

21 years, 4 months

1
0
0 0

System 36 going dirt cheap (currently $1) for local pickup in Dallas, TX

by wmaddox＠pacbell.net

Somebody ought to grab this... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=74946&item=514221499… --Bill

21 years, 4 months

1
0
0 0

Santa, for Christmas I would like

by aek＠spies.com

I guess I should try and copy the drive data onto a spare disk in case it decides to fail -- You should back up the software you have, assuming it WILL fail. -- anyone knows where I can get some AOS/VS media from? -- try bruce ray (bkr(a)wildharecomputers.com)

21 years, 4 months

2
1
0 0

Calcomp 1039 plotter in UK

by djg＠drs-c4i.com

If anybody is interested email plotter(a)pdp8.net which will forward to the plotter owner (spam protection). Email I got offering it: Got your details from the internet. I have an old Calcomp 1039 plotter which I need to dispose of. I note that you may be interested in PDP bits but don't know if this is the sort of beast you may want! It certainly used to be connected to a PDP in the distant past. It has most of the original accessories in their large & small black boxes plus umpteen rolls of media If you want any info please feel free to call me on 01727 875191. leave a voice mail if absent. Or if you know of anyone else who may want such a thing rather than being destined for the local tip! Regards Graham Simms In Hertfordshire.

21 years, 4 months

2
1
0 0

VCF 7.0 Pictures

by dwight.elvey＠amd.com

>From: "Wayne Smith" <wayne.smith(a)charter.net> > >I have posted a few pictures taken during VCF 7.0 at >http://webpages.charter.net/jpepperman/VCF%207.0.html. > >-W > Hi Of course my exhibit wasn't even noticed or photographed. As usual Sellam gave me half a table and most just figured that I was part of the exhibit next to me ( North Star ). Since my machine was also a woodie, ( much rarer than a North star ) it just blend into the background. Maybe next year I'll be noticed. Dwight

21 years, 4 months

3
2
0 0

hp 9121

by nataliac＠uvigo.es

I have a Dual Disk Drive HP 9121 that is cabled to an HP 9816 whith operative system HP Basic 2.0. When I copy or save file or program put the message "error 88: read data error". Can you help me? What is the Problem? thanks you and pardon for my english. Natalia Caparrini Spain

21 years, 4 months

1
0
0 0

MSDos on a dial up ISP?

by ron.hudson＠sbcglobal.net

How do you do that?

21 years, 4 months

3
2
0 0

Phllips Logic Analyzer Manuals

by aw288＠osfn.org

I have a set of operators manuals for the Phillips PM3551/10/30/50 and /70 logic analyzers (early 80s). One is in a binder, the other is just bound - a total of about 1 1/2 shelf-inches of information. Anyone need these for a couple of bucks plus shipping? William Donzelli aw288(a)osfn.org

21 years, 4 months

1
0
0 0

ZX81 denigrated! (was Re: Approaches to projects)

by dwight.elvey＠amd.com

>From: ard(a)p850ug1.demon.co.uk ---snip--- > >The expansion connector (the physical form of it, the fact that if the >RAMpack wobbles, the machine crashes). > Hi As I've stated in the past, put some DC#4 silicon grease on the edge connector and you won't have issues with the contacts. Dwight

21 years, 4 months

1
0
0 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb