http://www.cdw.com/shop/products/Raritan-Dominion-KX-PS-2-CIM/597051.aspx?cm
_mmc=ShoppingFeeds-_-GoogleBase-_-Servers%20_%20Server%20Management/KVM%20Co
nsoles%20_%20Switches-_-597051_Raritan%20Dominion%20KX%20PS_2%20CIM_RAR-DCIM
-PS2
<http://www.cdw.com/shop/products/Raritan-Dominion-KX-PS-2-CIM/597051.aspx?c
m_mmc=ShoppingFeeds-_-GoogleBase-_-Servers%20_%20Server%20Management/KVM%20C
onsoles%20_%20Switches-_-597051_Raritan%20Dominion%20KX%20PS_2%20CIM_RAR-DCI
M-PS2&gclid=CLrwnMzA6rsCFa4-Mgoddz0A6A> &gclid=CLrwnMzA6rsCFa4-Mgoddz0A6A
A large qty of these are available to me, new.
Any takers?
Where do you want to be on price?
Cindy Croxton
Electronics Plus
1613 Water Street
Kerrville, TX 78028
(830)792-3400 phone (830)792-3404 fax
AOL IM elcpls
_____
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3658/6978 - Release Date: 01/05/14
http://www.ebay.com/itm/BLACKBOX-EHN051-0010-10-FT-VGA-PS2-PS2-M-SERVSWITCH-
CABLE-USED-/221148056077
I have 17 pcs of these NEW, available to me.
Any takers out there?
If so, where do you want to be on price?
Cindy Croxton
Electronics Plus
1613 Water Street
Kerrville, TX 78028
(830)792-3400 phone (830)792-3404 fax
AOL IM elcpls
_____
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3658/6978 - Release Date: 01/05/14
Here is a first draft. Anything wrong/missing architecturally?
Ethernet Bus Interface Board
2013-12-21 aek
+--------------+
| 4Mx16 BBSRAM |
+------+ | AS6C1616 |
| | +------+-------+
LEDs - + ARM | |
SD -- + uCtl | JTAG +------+-------+
USB -- + +-----------+ | -> Simulated Peripheral Registers
ENET - + +-----------+ FPGA | Bus Monitor / Adr Mapper
SER?-- | | ARM intf | | Bus Master Controler
+------+ +------+-------+
|
+------+-------+
| |
| 5v<->3.3v |
| Bus Buffers |
+--------------+
The entire address space of the host is maintained in the SRAM
ARM performs DMA by placing the data to be transfered where it
will appear on the host. If the local memory is the system memory,
we're done, just clean up the DMA registers. If not the FPGA does DMA
to synchronize local memory with core. 3 cycle data break side effects
will have to be investigated. Does any driver watch the value of ADR,WC
in memory while a DMA is occurring?
Bus transactions are snooped to maintain consistency on the PDP-8
where some core memory is on the Omnibus. This may work OK on small
11's, too but won't be the right thing to do on an 11/70 where
memory transactions occur that are invisible to the Unibus.
It should be possible to simulate all the front panel functions of
an Omnibus machine and to capture all of the state in real time for
all of the major registers from watching Omnibus transactions.
It is also possible to adapt the board to be a dedicated bus analyzer or
soft front panel or peripheral/ memory exerciser for any supported bus
architecture.
All registers and supported peripherals are obviously soft. The configuration
is stored on the SD, along with the FPGA bitstream. Everything should be
reconfigurable through transactions across the Ethernet by updating files on
the SD card.
Battery-backed SRAM was chosen over FRAM because of cost.
I'm not sure if a local serial interface would be that useful other than
for debugging messages.
There are a small number of LEDs hung off of a STP08DP05
Small local SPI NOVRAM for configuration/bitstream storage? SD hot-swap?
Larger local storage? Is performance an issue on Omnibus/Qbus/Unibus CPUs?
They are slow enough busses that they'll saturate in the couple MB/sec range.
Write-through track caching in SRAM?
Block mode on QBus
.. and on and on
Ethernet Peripheral Controller
This is the mirror of the Bus Interface Board. It provides block-level data
that the Bus Interface sends into the computer. In its simplest form, there
is no hardware at all, it is just a simulation running on a computer on the
network. The second simplest is hardware that understands the Ethernet
peripheral command protocol but has a simple enough interface to the physical
device that no FPGA is required. It may also not need any local storage. The
most complicated could look like the Bus Interface Board, with local SRAM and
FPGA. A Diskferret-like forensic disk interface would be an example of this.
I'm looking for a BC80J-20 cable... that's the one that goes from the
RL controller card to the first drive, with a 40 pin header on one end
and that big quick-release connector on the other end.
(I am tired of failures and damage to the rigged ribbon cable/IDC
header I've been using, and now that I'm chasing a fault in my two-
RL02 system, I can't swap drives without taking the cover off to get
to the header connectors inside).
thanks
Charles
Ask and you shall receive..
4 BNC to PC VGA, new, qty 4, approx 4 feet long, $15 each
3 BNC to PC VGA, used, qty 1, approx 3 feet long, $10
5 BNC to PC VGA, used, qty 1, approx 5 feet long, $15
4 BNC to 15-pin Rasterops PN 9000-0059, new but dusty, $15 (will not work on
PC, wrong end)
4 BNC to 15-pin Rasterops PN 9000-0001, new, $15 (will not work on PC, wrong
end)
Shipping $6 for the 1st cable, and $3 each additional cable ground in US.
Cindy Croxton
Electronics Plus
1613 Water Street
Kerrville, TX 78028
(830)792-3400 phone (830)792-3404 fax
AOL IM elcpls
_____
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3658/6978 - Release Date: 01/05/14
As I don't have a logic analyser to help me with my analysis of the MFM
interface, can anyone tell me how the MicroVAX 2000 determines disk size? I
know it is related to the number of heads, but what does the drive do when
the host asks for a head that does not exist? How does it report this back?
The only thing I can think of is the Ready signal, could that be it?
Regards
Rob
From: Liam Proven <lproven at gmail.com>
> So, an ad-hominem attack is your idea of a balanced reply, is it?
Can't attack the message, attack the messenger. Good to see my assessment
was spot on.
KJ
> I'm just wondering if anyone knows what a typical value for a single unit
> with nothing fancy is? I note a recent auction had two of them together
for
> $1400 - Am I correct to imply from that that the value of an individual
unit
> is probably less than $700 (that set was unique due to the systems being
> linked and that control box they had, I think).
A working, complete, 1975-6 SWTPc with top and bezel, original backplane,
original CPU and RAM with an MP-S card is worth $1000+. That would be the
bare minimum system. $700 is too low for a working system. The newer 6809
SWTPc's would be worth less, maybe you can get one of these for $700.
Bill
I've seen a couple of vague references to 3rd party memory cards for the
VAX 11/730, equivalent to the M8750, that used denser DRAM chips in order
to use less power. Unfortunately, my google-fu has turned up nothing.
Does anyone know who made these cards and what part number they would be
(assuming they exist at all)?
KJ
Hi all,
I think I'm not getting it. I have a BA23 with a 11/83 and a RQDX3. I have
set the IDs on the RD54s (XT2190s) to ID 0 (pin 1 and C) and ID 1 (pin 2
and C) but yet ZRQCH0 or RT-11 does not seem to find the second disk, which
should be DU1, right?
Am I missing something here?
regards,
reiche
Has anyone archived the DEC InfoServer 100 firmware anywhere?
I see that CHM has one,
http://www.computerhistory.org/collections/catalog/102682746
Is the InfoServer 100 motherboard identical to that of the MicroVAX
3100 Model 20, except for the firmware? From information I've found on
the net that appears that it might be the case but I haven't found a
definitive answer on that.
I have a MicroVAX 3100 Model 20 that isn't too interesting and it
might be more interesting if it could be converted to an InfoServer
100 with a firmware swap.
-Glen
>
> Subject: Re: DEC InfoServer 100 Firmware archived anywhere?
> On Jan 4, 2014, at 12:53 PM, Glen Slick <glen.slick at gmail.com> wrote:
>
> > Has anyone archived the DEC InfoServer 100 firmware anywhere?
>
I have V3.5a.
--
Michael Thompson
On Jan 3, 2014, at 12:00 PM, cctalk-request at classiccmp.org wrote:
> From: Brad Parker <brad at heeltoe.com>
> To: General Discussion: On-Topic and Off-Topic Posts
> <cctalk at classiccmp.org>
> Subject: Re: Need DEC BC80J-20 cable
> Message-ID: <52C6D5C1.3080207 at heeltoe.com>
> Content-Type: text/plain; charset=ISO-8859-1; format=flowed
>
> On 12/15/13, 10:48 PM, Charles wrote:
>> I'm looking for a BC80J-20 cable... that's the one that goes from the
>> RL controller card to the first drive, with a 40 pin header on one
>> end
>> and that big quick-release connector on the other end.
>>
>> (I am tired of failures and damage to the rigged ribbon cable/IDC
>> header I've been using, and now that I'm chasing a fault in my
>> two-RL02 system, I can't swap drives without taking the cover off to
>> get to the header connectors inside).
>>
> I think I'm looking for one of these as well. Or maybe someone here
> can
> point me to what I really want :-)
>
> I have an RL02 driver and an RL02 controller, but I seem to have
> lost/misplaced the "cabinet kit". I could swear I had one at one
> point.
>
> So, the RL02 drive has a terminator and a nice long round cable which
> seems to have a 2x.1" header. But I believe I need the cable part
> which
> is normally install on the cpu cabinet. My guess is it would cable a
> shielded ribbon cable with a connector for the board header and the
> other end would have a metal bracket and something to mate with the
> nice
> round cable...
>
> Is this even close?
>
> -brad
The BC80J-20 has the 40-pin header on one end and enough flat ribbon
cable to make it out the back of the chassis... I have never seen a
"real" one but I believe it has some kind of transition to the round
cable (which then has the quick-disconnect on the other end)?
BTW, Continental Computers answered my quote request with they can
"let it go for $145"... that's about four times what I expected to pay
for one!
-Charles
Hey guys,
I am keeping an eye out for an SWTPC 6800 system. I was hoping for one with
the SWTPC black case. I thought that'd be nice to go with the CT-1024
terminal I have (if I get it working). Have developed a bit of a
fascination with SWTPC lately.
I'm just wondering if anyone knows what a typical value for a single unit
with nothing fancy is? I note a recent auction had two of them together for
$1400 - Am I correct to imply from that that the value of an individual unit
is probably less than $700 (that set was unique due to the systems being
linked and that control box they had, I think).
I keep seeing this one popping up on ebay:
http://www.ebay.com/itm/SWTPC-6800-in-custom-case-with-PLEXIGLASS-Cover-Rare
-/151200879158?pt=US_Vintage_Computers_Mainframes
<http://www.ebay.com/itm/SWTPC-6800-in-custom-case-with-PLEXIGLASS-Cover-Rar
e-/151200879158?pt=US_Vintage_Computers_Mainframes&hash=item2334465236>
&hash=item2334465236
But it's got a custom case, and looking at the written dates on the ROMs
appears to be later than what I believe was the 6800's heyday (mid to late
70s?). Did SWTPC sell 6800s as parts like that, or is this something
someone cobbled together?
Brad
Does anyone have any information about these HP hard drives?
https://www.dropbox.com/sc/xovh6yyel6zhzil/B4UelO3lhK
Model 97500-85620.
They have a 40 pin connector on them, but no power input. Doing a search
shoes a mix of companies describing these as either HPIB or IDE. I
believe HPIB is probably the case, but I can't find any documentation for
the drives to be 100% sure. I would love to find a manual/spec sheet for
the drives.
Thanks!
Garrett Meiers
Founder, BitHistory.org &
President, ConsulNIX, LLC
www.BitHistory.orgwww.linkedin.com/in/theunixguy
Hello all,
how to connect a HP 9000/300 with RGB BNC video out to a modern LCD monitor, which has only a D-Sub VGA video connector.
Can I simply use a classic BNC to VGA cable just reverse connected?
Since from 2015 on there will be no new monitor supporting VGA singnals anymore what we have to do to connect our old workstations?
Andreas
Hi!
It's mandatory to connect the printer?
Trying to access the internal drives leads in 013 error (Device not
attached), both for D80 and D40.
I've not opened it yet.
The drives spin, I can hear the noise inserting a disk.
Thanks!
I've been looking at the various means if creating a disk from image.. but given the hardware required and rigging it all up.. I'd rather just obtain a copy somewhere i think.
Sent from Samsung Mobile
<div>-------- Original message --------</div><div>From: Chuck Guzis <cclist at sydex.com> </div><div>Date:01/03/2014 4:29 PM (GMT-08:00) </div><div>To: "General Discussion: On-Topic and Off-Topic Posts" <cctalk at classiccmp.org> </div><div>Subject: Re: Intel MDS 225 system being auctioned by Chicago Transit Authority </div><div>
</div>On 01/03/2014 02:19 PM, Dave Mabry wrote:
> If an MDS225 was "upgraded" with the double density boardset and the
> internal cable, that turns the internal drive into a double density only
> drive.
>
> I've seen several that were upgraded that way.
Yeah, I remember both the DD and SD versions of the board set--and I
remember how hot the channel board ran.? One of the first questions I
asked on the VCF posting was whether or not the OP had the DD board
set--kind of hard to miss.? He reported that he did not, so he's running
off the 8271 built-in controller.
If he was using the DD board set, that would create an interesting
issue, as it uses MMFM, not MFM for encoding.? Not something easily done
on a PC.
Fortunately, it's clear that plain old SSSD disks will work just
fine--and he can probably use a PC to write the images to disk.
--Chuck
Hi! Good news! The S-100 buffered prototyping board PCBs have arrived!
Here is your chance to build your own S-100 board project!
Here is more information on the S-100 buffered prototyping board. These
boards have been respun and contain some minor improvements from previous
versions.
http://www.s100computers.com/My%20System%20Pages/Prototype%20Board/Prototype
%20Board.htm
The PCBs will be $20 each as per the usual arrangement. Shipping in the US
is $3 for a single PCB and $2 for each additional PCB. Shipping
internationally is $12.75 for a single PCB and $3 for each additional PCB.
This is for the bare basics USPS first class postage with no tracking or
insurance. The builder assumes all risk of delivery as per usual
arrangement.
My preference is to sell these PCBs to vintage computer/home brew
computer/classic computer hobbyists first but if there are any remaining
boards I will put them on eBay.
Please send a PayPal to LYNCHAJ at YAHOO.COM with the subject "S-100 buffered
prototyping board" and I will send your board(s). There are several PCBs
left.
Thanks and have a nice day!
Andrew Lynch
I just bought one of those off ebay for $50. ?Shipping was a killer though. ?Very nice machine. ? Just wish I had a boot disk for it.
Brad
Sent from Samsung Mobile
<div>-------- Original message --------</div><div>From: Jason T <silent700 at gmail.com> </div><div>Date:01/02/2014 1:46 PM (GMT-08:00) </div><div>To: "General Discussion: On-Topic Posts Only" <cctech at classiccmp.org> </div><div>Subject: Re: Intel MDS 225 system being auctioned by Chicago Transit Authority </div><div>
</div>On Thu, Dec 12, 2013 at 3:48 PM, Colin Howell <colin.d.howell at gmail.com> wrote:
> The Chicago Transit Authority is auctioning off a whole load of
> miscellaneous stuff (including a couple of rail cars!). One of the items
> being auctioned is what appears to be an Intel MDS 225 "Blue Box" (4 MHz
> 8085A system) complete with an MDS 720 disk expansion unit and some sort of
> Control Data hard disk.
>
> The specific lot is here:
>
> http://ricklevin.nextlot.com/public/lot/15005194?section=photos
Despite being local *and* placing a low bid on the lot, I completely
dropped the ball (mouse?) and forgot about the closing.
Did anyone here end up with this fine blue machine?
Hey everyone,
I'm a fairly middle-weight collector based in Squamish, BC. I have about 70
machines total, a few of which are projects that I'm seeking advice/help on.
One of them is an SWTPC TVT-II CT-1024 terminal. I bought it a couple of
months ago, complete on ebay. I've tried to read as much documentation on
these as I can find, but there are a few things I can't figure out.
I've posted a few videos of it -- including this one:
https://www.youtube.com/watch?v=c2rX10-m8GQ
Initially when I turned it on, I got just garbled screen. The first monitor
I attempted to hook up to was my Apple III, which apparently can't handle it
at all. Then I went to my Commodore 1702 and 1084, and I can adjust things
enough to make out a picture and characters, but it's repeated several
times, as you can see in the video. On the first few powerups I'd see the
occasional flickering of a full field of questionmarks, but it wouldn't
stay. I learned about the voltage trimmer on the PSU and have trimmed it to
5V exactly, and now when I turn the unit on, the field of question marks
comes up and stays. There is a switch I've discovered (none of them are
labelled) that causes that field to disappear. I think this puts the unit
into terminal mode. The keyboard is connected to the serial card (I think
there is a connector on the motherboard where it could go also if you didn't
have that). I also played with some trimmers on the motherboard that adjust
horizontal position and so on.
Anyway, what you see in the videos up to the most recent one is the most I
can make it do. It doesn't seem to respond to keystrokes, and the
documentation I have is limited or a bit over my head. Mainly I'd like to
figure out why the screen is so messed up.
Much appreciated if there are any of you out there familiar with these old
timers and would have an idea where to begin looking.
Brad
On Fri, Jan 3, 2014 at 4:17 PM, Mark J. Blair <nf6x at nf6x.net> wrote:
> I'm just getting started in DEC stuff in general and RL02 drives in particular. I'm
> putting together a PDP-11/44 system, and I hope to try running both RT11 and
> BSD on it.
The 11/44 has split I&D so you can go with 2.9BSD or 2.11BSD.
Generally speaking,
you'd probably want to go with 2.11BSD because you can.
> Would a two-drive system be sufficient, or would I need more storage space?
> I have four RL02 drives in unknown condition, but I was only planning to rack
> up two of them with the PDP-11/44 and a Kennedy 9610 9-track tape drive.
My experience is that I was able to fit the base install on the first RL02 pack,
but there wasn't room to pull the sources and rebuild the kernel without more
storage. Even so, 20MB total was kinda tight, maybe too tight. Back when
this hardware was current, it was IIRC easy to plunk 2BSD onto one or two
RK07s (28MB each). When I started playing with simh 15+ years ago, it was
easier to define an RP03 and install into one big 60MB pot (which is how I
helped find a simh bug long ago). You can give it a try now with simh by
practicing with a couple of 10MB image files and the 2BSD distro tape images.
It's an authentic experience in terms of the approach you'd have to take
and the commands you'd have to type (without bad blocks and tape errors
to pull you astray). If it fits on 2x RL02 in simh, it'll be the same on real
hardware. That reminds me - you have to have error-free packs. DEC used
to sell RL02-EF packs for use with UNIX (RT-11 can mark bad spots
on the disk and if they aren't in the first tracks or if there aren't too many,
you can mark those sectors allocated and work around them. Not so with
BSD).
For RT-11, even a single RL02 is plenty of space. I used develop applications
on an 11/23 and an RL01 was enough for the OS and all my code.
> My PDP-11/44 pile came with an RL11 board and the cable from it to the
> first RL02 drive. It doesn't have a bulkhead fitting; it just goes from
> the controller directly to the connector that plugs into the back of an
> RL02 drive. I haven't looked at the cable carefully yet, but I can
> examine, measure and photograph it if that would be helpful to anybody
> else in this thread.
The bulkhead bracket was convenient but not essential. To get out of the
CPU cabinet, you almost certainly have a flat 40-pin cable, then the
transition connector, then probably the usual drive-to-drive round cable,
but just laying in a line, not bolted to your rack. It will work just fine but
there's a risk of kinking or pinching cables if you move the drives around
a lot (the bracket has a spot to screw down a tab on the shield of the
round cable as a strain relief with either a 6-32 or 4-40 machine screw).
I know I have at least 1-2 bad cables from excessive flex/pinching (I've
thought about cutting them at the point of physical damage and trying
to make one or two of them into a BC80M cable since I have the right
crimper for those Berg pins).
> BTW, I am looking for drive ID lenses for my RL02 drives. I need a "1" and
> a "2", and I could either buy them outright or trade "0" lenses for them. My
> RL02 pile came with three "0" lenses and a "3".
My recollection is that it was common to have 1-2 drives, but not 3-4 (for
reasons of cost), and as systems were consolidated, there were more "0"
plugs than the others combined.
I've thought about molding replacements or even 3D printing them (they'd
be suitably light-transmissive if made from natural ABS or especially natural
or clear PLA) but I haven't tried making an STL of them. There'd be a risk
of the fingers snapping off and getting stuck in the switch mechanism, but
I think an ABS drive plug that was subjected to the acetone vapor treatment
would firm up nicely and be resistant to the layers separating.
Anyone care to make up an engineering drawing of the plug with tolerances
in the 0.1mm range?
-ethan
I recently bought a lovely PDP11/45 in a H960 rack, with the CPU, a Unibus
Expansion box and an RK05 drive. I am guessing the whole thing must weigh at
least 100Kg, possibly 150Kg or even more (my worst case estimate is 200Kg).
I am concerned whether the floor of the upstairs room where I now have it
can bear the weight. I have placed it right next to a load bearing wall to
ease the strain on the joists. Can anyone tell me what sort of weight a
normal UK upstairs floor can bear? If my guessed weight is anything close to
the limit I will weigh parts of the machine to get a more accurate idea of
the actual weight.
Thanks
Rob
You'll need a Sync On Green to VGA converter to separate the sync signals.
-Rik
-----Oorspronkelijk bericht-----
Van: "Andreas Holz" <aswood at t-online.de>
Verzonden: ?4-?1-?2014 09:24
Aan: "cctalk at classiccmp.org" <cctalk at classiccmp.org>
Onderwerp: BNC Video out and LCD monitor with VGA D-Sub video in
Hello all,
how to connect a HP 9000/300 with RGB BNC video out to a modern LCD monitor, which has only a D-Sub VGA video connector.
Can I simply use a classic BNC to VGA cable just reverse connected?
Since from 2015 on there will be no new monitor supporting VGA singnals anymore what we have to do to connect our old workstations?
Andreas
I purchased a VAX 4000-500 last month and am pretty excited. I've only
owned MicroVAX'es in the past, and this is the first larger VAX I've had..
Although, it's more of a medium-sized VAX. :)
?Came with an Infoserver 100, and a R400X? Expander with three drives. I
haven't fired it up yet, but was told it all works.
I have the DSSI cables, and need to do a little reading before I connect
these up, and fire it up. Any pointers for working with this setup -- in
particular DSSI and the Expander, would be appreciated.
https://www.dropbox.com/sc/4ziahrtsp5lw57l/fy1lCpcoar#/
?Thanks,
Garrett Meiers
Founder, BitHistory.org &
President, ConsulNIX, LLC
www.BitHistory.orgwww.linkedin.com/in/theunixguy
On Jan 3, 2014, at 5:18 PM, cctalk-request at classiccmp.org wrote:
> From: Ethan Dicks <ethan.dicks at gmail.com>
> To: "General Discussion: On-Topic and Off-Topic Posts"
> <cctalk at classiccmp.org>
> Subject: Re: Need DEC BC80J-20 cable
> Message-ID:
> <CAALmimndRqNj0eDbaYdyFGz+VsO0pikpHK_1O5wn4R-n2eV5sg at mail.gmail.com>
> Content-Type: text/plain; charset=ISO-8859-1
>
> On Fri, Jan 3, 2014 at 1:35 PM, Al Kossow <aek at bitsavers.org> wrote:
>>> BTW, Continental Computers answered my quote request with they can
>>> "let it
>>> go for $145"... that's about four times what I expected to pay for
>>> one!
>>
>> The BC80M listed for 57.50 should work fine.
>
> That one looks to be 6' (BC80M06) which is the only length I've seen
> in person. They also have a BC80M25 for three times as much.
>
>> You'll probably have to fiddle with the big drain cable on the
>> controller end.
>
> I remember that big fat braid. ISTR it was not easy to find a
> convenient place to bolt that down on a BA23.
>
> -ethan
I am sure I can find a place to fasten it, even if I have to modify
the braid (or the chassis) slightly...
Anyway I was thinking of just bending over and paying the $57.50.
Until I got to "standard 9-13 day shipping $15.00" and it goes up from
there. Postage rates have really gotten ridiculous and the companies
(except McMaster-Carr who are quite reasonable for shipping) are
adding on their profit too.
Perhaps I can locate some surplus multiple twisted pair cable and
carefully solder the ends to a header connector. There are 13(?)
twisted pair differential signals and the rest are no-connects or
grounds. As Henk pointed out, some of the trouble may be the 6' of
unshielded ribbon cable (which is also smaller gauge than the twisted
pairs)...
-Charles
I have come across a strange problem with my MicroVAX 2000. If the hard disk
is not plugged in I get absolutely nothing on the console, as if the machine
was dead.
I have perused the technical documentation and I cannot find anything that
describes this behaviour. Does anyone know why it might do this and which
signal(s) prevent the console coming up?
I need this to be able to do some initial testing of a basic emulation of
the RD5x disks with an FPGA.
Thanks
Rob
One other project I'm having some difficulties with is a Commodore PET 2001
that I've had for 10 years. In that time, turning it on only ever produced
a 'blank' raster screen, as in this video:
https://www.youtube.com/watch?v=m5Rkwu858zA
For years I assumed the computer was basically dead and kept it on static
display. But just recently I acquired a good working 2001-16, and
discovered that I could use its monitor with the 2001-8. I discovered the
standard garbage screen, and after acquiring a whole bunch of rare NOS
6540s, and some 6550 RAMs, was able to get the 2001-8's motherboard fully
functional. The screen however remains the same. I have connected it to
the other working PET to no avail. I have even used the working PET's own
cabling. So my problem is basically the video board. I've fixed the
brightness control but that's as far as I've dared go given the voltages
involved with a CRT. Wondering if anyone has any other ideas on where my
problem could be.
Thanks!!
Brad
On this e-mail list, plus another one that I belong to (on a totally different server as far as I know), I've started to received multiple copies of the Digest. Up to four copies of each digest are being sent. Same on the other e-mail list I belong to.
List owner - was a recent upgrade to the Mailman software put on your server just a few days ago? It seems coincidental that both list, both using Mailman software, are suddenly behaving this way.
Kevin Anderson, Dubuque, Iowa
Subject:
Re: Need DEC BC80J-20 cable
From:
Brad Parker <brad at heeltoe.com>
Date:
Fri, 03 Jan 2014 10:22:41 -0500
I think I'm looking for one of these as well. Or maybe someone here
can point me to what I really want :-)
I have an RL02 driver and an RL02 controller, but I seem to have
lost/misplaced the "cabinet kit". I could swear I had one at one point.
So, the RL02 drive has a terminator and a nice long round cable
which seems to have a 2x.1" header. But I believe I need the cable
part which is normally install on the cpu cabinet. My guess is it
would cable a shielded ribbon cable with a connector for the board
header and the other end would have a metal bracket and something to
mate with the nice round cable...
Is this even close?
-brad
Brad,
From the controller, there's a shielded flat ribbon cable with a Berg
on either end.
Next is a Berg->RL02 cable adapter which can mount in a distribution
panel. Not sure what the RL02 connector is, but it's the same as is on
back of the RL02.
Next, is the nice round RL02 cable with the special twist-lock
connectors on either end.
Last, of course, is the RL02 with two connectors, one having a
terminator if end of chain.
- John S.
From: "Robert Jarratt"<robert.jarratt at ntlworld.com>
To: "General Discussion: On-Topic and Off-Topic Posts"
<cctalk at classiccmp.org>
Subject: Keeping a Heavy Machine on a Domestic Suspended Floor (UK)
Message-ID:<068e01cf07f6$bde4ee40$39aecac0$(a)ntlworld.com>
Content-Type: text/plain; charset="us-ascii"
I recently bought a lovely PDP11/45 in a H960 rack, with the CPU, a Unibus
Expansion box and an RK05 drive. I am guessing the whole thing must weigh at
least 100Kg, possibly 150Kg or even more (my worst case estimate is 200Kg).
I am concerned whether the floor of the upstairs room where I now have it
can bear the weight. I have placed it right next to a load bearing wall to
ease the strain on the joists. Can anyone tell me what sort of weight a
normal UK upstairs floor can bear? If my guessed weight is anything close to
the limit I will weigh parts of the machine to get a more accurate idea of
the actual weight.
Really, compare it to a piano! Even an upright piano weighs
more
than 200 Kg. I seriously doubt you have any danger. You
can probably
get the true weight from installation docs on bitsavers. It
is possible
it weighs more than 200 Kg, but still less than some really
heavy
furniture or a grand piano.
Jon
Congrats, a nice find!
You should post some pictures.
-Rik
PS. Gelukkig 2014.
-----Oorspronkelijk bericht-----
Van: "Jos Dreesen" <jdr_use at bluewin.ch>
Verzonden: ?2-?1-?2014 23:24
Aan: "On-Topic and Off-Topic Posts" <cctalk at classiccmp.org>
Onderwerp: 2014 started off well here..
The local craigslist equivalent yielded a tiny advert "Imsai 8080 computer from 1977".
price : 110 USD, negotiable....
The picture was a tiny B/W jpg lifted from the internet, and did not look too promising.
The actual hardware ?
An absolutely mint, as-new, IMSAI 8080...
>from the orignal owner....
with full documtation, including original invoice...
in the original IMSAI cardbox !
Also MPU-A and MIO cards..
24 Kbytes of 2102 SRAM..
all ICs socketed..
with papertape software....
handpulled papertape reader...
Needless to say no further price negotiations took place.
About the only minus is the MDC-A4 floppy controller, which requires more difficult to find hardsectored disks.
( Original diskdrive and disks were scrapped a long time ago )
I will also need to find some extra s100 connectors to complete the backplane.
it seems the '2014 project is defined !
Jos
(I'm not subscribed to the list, but I'm passing this along because I
thought it would be of interest to list members.)
The Chicago Transit Authority is auctioning off a whole load of
miscellaneous stuff (including a couple of rail cars!). One of the items
being auctioned is what appears to be an Intel MDS 225 "Blue Box" (4 MHz
8085A system) complete with an MDS 720 disk expansion unit and some sort of
Control Data hard disk.
The specific lot is here:
http://ricklevin.nextlot.com/public/lot/15005194?section=photos
No idea whether any of the hardware is functional.
Bids for the whole lot currently stand at $60. Auction for this lot ends
December 18th (Wednesday), 11:10 AM local time (Central Standard Time).
More info on the auction can be found via the link above.
General news story on the auction:
http://www.dnainfo.com/chicago/20131212/downtown/cta-selling-bus-signs-trai…
Colin Howell
>
>Subject: VT-180 (Robin) EPROM images?
> From: "Robert Armstrong" <bob at jfcl.com>
> Date: Sat, 10 Mar 2007 20:23:04 -0800
> To: <cctech at classiccmp.org>
>
> Does anybody have images of the v2.1 Z-80 firmware for the VT-180 (aka
>Robin) ? At least, I think 2.1 was the last version ever released. They
>should be DEC part numbers 23-017E3-00 and 23-021E3-00.
>
>Thanks,
>Bob Armstrong
I have enough of them laying around I could supply the actual roms. I've
never imaged them as It's easier to replace the code outright.
Curious why are you looking for them?
Allison
Hi,
I came across a qbus card manufacturded by Data Technology Corp. labelled DTC LSI11-2. Has a 50pin header connector upper left hand side when looking at the component side. Searching around on bitsavers revealed a manual for the DTC LSI11-1. It seems to be a disk controller. Does anyone have any info on the 11-2? Switch settings, and/or drives that can be connected to this? I can provide pics of the controller if it would help.
thanks
alex
p.s apologies if this msg shows up twice, e-mail has been acting up today.
--
My apologies for the missing links; they got stripped out by the mailing list software.
Please see http://seefigure1.com for the various things I referenced.
Thanks,
Rob Ferguson
Can someone put the poor bastard out of this misery ;)
I think loosing your short term memory is one of the first signs of Alzheimer..
-Rik
-----Oorspronkelijk bericht-----
Van: "billdeg at degnanco.com" <billdeg at degnanco.com>
Verzonden: ?1-?1-?2014 18:07
Aan: "cctech at classiccmp.org" <cctech at classiccmp.org>
Onderwerp: Message from BillDeg
Effective Immediately
After 16 years of use, it's time to retire billdeg at degnanco.com.
Henceforth all emails to billdeg at degnanco.com will be deleted. If you wish to contact Bill by email, please use billdeg at buzz1.com
B
Effective Immediately
After 16 years of use, it's time to retire billdeg at degnanco.com.
Henceforth all emails to billdeg at degnanco.com will be deleted. If you wish to contact Bill by email, please use billdeg at buzz1.com
B
I have managed to break one of the wires in the ribbon cable of the DSSI
cabinet kit in my BA213 MicroVAX 3400. It looks like it would be fairly easy
to replace with any 50-way ribbon cable with a male connector and multiple
female connectors. The only problem is the connector to the front panel, the
ribbon is split into two at the external connector and goes into two
separate halves of the back of the connector. Is it possible to open up the
back of the connector without damaging it?
The alternative would be either to find a replacement cable (anyone have
one?) or try to repair the broken wire
Regards
Rob
Over the last year or so, I've been researching the history of the Commodore SuperPET.
I've just pushed a couple of things that I've been working on out to my website, and I thought people here might find them interesting.
First is a narrative about how the SuperPET came to be, and how work on academic software at the University of Waterloo culminated in a collaboration with Commodore. Much of the information stems from new research which I conducted in the UW Archives this past summer.
It also traces the origin and fate of the MICROWAT, a precursor hardware design that had a great deal of influence on the SuperPET. The whole thing can be found here: How the SuperPET came to be
Second, I've written a timeline that documents significant events in the birth, life and decline of the SuperPET. That's here: The Commodore SuperPET: a timeline
Third, one of the more interesting -- and mostly undocumented -- features of the SuperPET was its built-in ability to be a client to a remote fileserver; this relied on an RPC-like facility called HOSTCM that used the serial line as a transport. I have reverse engineered the protocol, and written a program that acts as a HOSTCM fileserver for the SuperPET. It runs on a variety of modern machines, including Mac OS X, FreeBSD and Linux.
Among other things, this means that you can use a SuperPET without an attached diskette drive, and that you can move disk images, files and programs between the SuperPET and modern machines without specialized hardware. You can find the program here: HOSTCM and the protocol documentation here: The HOSTCM protocol
Finally, I've written a couple of utilities that are useful for manipulating archived Commodore disk images for use with my HOSTCM implementation. That can be found here: Utilities for HOSTCM
Oh, and there are some good pictures, too.
If anyone has comments or questions, please let me know.
Cheers,
Rob Ferguson
Effective Immediately
After 16 years of use, it's time to retire billdeg at degnanco.com.
Henceforth all emails to billdeg at degnanco.com will be deleted. If you wish to contact Bill by email, please use billdeg at buzz1.com
B
The SGI memory that I offered has already been claimed.
Thank you for all the responses!
Cindy Croxton
Electronics Plus
1613 Water Street
Kerrville, TX 78028
(830)792-3400 phone (830)792-3404 fax
AOL IM elcpls
_____
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3658/6962 - Release Date: 12/30/13
Happy New Year to everyone who uses the Common Era calendar,
since by the time this reply is read, New Year's day of 2014 will have
already started for some individuals.
If anyone who is reading this still uses RT-11 to change RT-11
programs and uses the RT-11 Symbolic Debugger, SD:, I have a
few questions.
As for using SD: (the RT-11 Symbolic Debugger), does anyone find
that SDHX.SYS uses too much low memory (1125 words)? Would
having an option to retain the Program Counter Locations (at least
the last 1000 addresses executed - in a circular buffer, of course) be
of help in debugging RT-11 code? Another option which I would
appreciate would be the ability to support the temporary execution
of other jobs while the current job being executed is placed into
.Wait state. Does anyone else agree? Under TSX-Plus and RSX-11,
that happens automatically, in addition to using VDT under RT-11.
BUT, SDHX.SYS freezes the complete RT-11 system when the
code being debugged is stopped at a break point, including even
clock interrupts.
Jerome Fine
The following is a partial list of mostly cpu boards surplus to my needs.
Please contact me off list if interested. Some are available without roms.
Some other boxes, boards here, but no list yet.
Shipping from 61853, Illinois.
M7264- 11/03 no memory $45
M7264- 11/03 W memory $60
M7270 LSI-2 $80
M8186 11/23 $100
M8189 11/23+ $160
M8044 MSV11-DD $40
Qty discounts available.
Also have several complete 11/44 CPU sets and a bunch of M7819, DZ11-A
boards.
Thanks, Paul
In the Netherlands, two Tandem Himalaya K200 systems (I believe
those are MIPS-powered, NonStop) with disks, tape cartridges,
spare parts and more. All for *free*.
<http://link.marktplaats.nl/760755920>
In the description it's mentioned that these systems used to run
at the NYSE Euronext stock exchange. (They were probably
decommissioned to be replaced with IA-64 NonStop systems,
or something else, who knows.)
It looks physically gigantic and that it may (sic) require three-phase
power. But, in the description the person that is offering it writes
that one system ought to fit in a BMW 5-series station wagon car
and that it will definitely fit in a 'rent-a-haul' type of trailer.
I'm fairly nearby it, I imagine others may too. But, I don't have
adequate power-requirements for it most likely. For who is
interested in trying out a 'NonStop' system (these seem very
rare, needless to say), maybe we could start some kind of
'fundraiser' and that whoever is interested pitches in a small
amount of money, then we can see if we can get this gigantic
monstrosity shipped to someone who can power it and so
that people can perhaps try it out through remote access...?
(Just an idea.)
- MG