test-drb May 2012

test-drb@ccmp.vtda.org

189 participants
220 discussions

Wait! There's more including MS-DOS 1.25!!!! was Sanyo MBC-550 (Yuck!) software available

by rigdonj＠intellistar.net

I'm still digging. I found more 550 stuff. I think this is everything that came with the 550. Here's a chance for you 550 owner's to get the whole set at one shot! Original DS-DOS box and invoice. Original Sanyo Easywriter ver 1.3 disk Original Sanyo disk box with 550 dos ver 2.11 and BASIC 1.25, two original Sanyo disk for InfoStar (set B disk 2 and 3 of 4; disks 1 and 4 are below), original Sanyo disk for DOS 1.25 and BASIC ver 1.1 Original Sanyo disk box with all three original disk of set A, WordStar and CalcStar and a backup copy of DS-DOS. Two card board dummy disks used to protect the floppy drives duing shipment. Joe > >A few weeks ago we were talking about the Sanyo 550 series and someone mentioned one of the alternates operating systems that supported 80 track drives in the 550. I said that was DS-DOS by Michtron. > > Today I found an old Sanyo disk package with four disks for the 550. One of them is DS DOS 2.11, one is InfoStar, one is MailMerge/SpellStar and the other is a disk of misc utilities. The first three are original disks. In additon, the InfoStar, MailMerge/SpellStar are Sanyo labeled disks that came with the 550. If anyone wants them, trade me something I can use and they're all your's. > > Joe

11 years, 11 months

Seeking information on some Qbus disk/tape controllers: Dilog DQ37, Emulex QT131 and UC07

by ethan.dicks＠gmail.com

Hi, All, I was going through a box of "interesting" cards last night and I came across three cards that I'm looking forward to using: o Dialog DQ37 - an S-box-handle Qbus SCSI controller o Emulex QT131 - a Qbus Pertec tape controller? o Emulex UC07 - a Qbus SCSI controller I found the UC07 manual on Bitsavers, so I'm good there for setup and configuration, but I was curious if anyone knows about different firmware revisions I should be aware of or seek to put on the card (I've owned plenty of Emulex communications controllers, and done plenty of firmware swaps on those, and since they put firmware (ROM chip) upgrade instructions in the manual, it makes me practically expect to have to do something to it). I could not find more than a couple of comments about the QT131, but I'm reasonably certain whatever jumper settings are on there are a) the defaults, and b) just fine. If anyone here has any experience with the QT131 or even better, a manual, that would be appreciated. As for the Dilog DQ37, I can find nothing except 3rd-party resellers offering to sell me one if I click the "give me a quote" button. The ones I have (2) appear to have the single-ended SCSI portion of the board populated and have a large bare patch that, from the component values on the silkscreen, seems to me to be for High Voltage Differential. No biggie. I don't have any HVD drives anyway. I don't own any S-box hardware, so "just plug it in an see what it looks like" is not the preferred method - I'd like to know more before I go further. I'm especially wondering if this is a TMSCP-only controller or if it will do MSCP and/or TMSCP, and if there are any firmware variations I should know about. So... anyone here know about these cards or where to find docs (besides the UC07 docs on Bitsavers)? Thanks, -ethan

12 years

IBM 5151 green phosphor monitors for sale

by sellam＠vintagetech.com

I have a limited number of IBM 5151 monitors for sale. This is the classic green screen monitor that shipped with the basic IBM PC 5150. Condition is adequate. They are dirty but I will clean them up before shipping out. Will test for basic functionality. No burn-in or other problems, but no warranty either. The price is $30 each plus shipping. First come, first served. Please contact me directly via e-mail. Thanks! -- Sellam Ismail Vintage Computer Festival ------------------------------------------------------------------------------ International Man of Intrigue and Danger http://www.vintage.org [ Old computing resources for business || Buy/Sell/Trade Vintage Computers ] [ and academia at www.VintageTech.com || at http://marketplace.vintage.org ]

12 years

Gooey TU58 rollers

by ajp166＠bellatlantic.net

> >Subject: Re: Gooey TU58 rollers > From: "Ethan Dicks" <ethan.dicks at gmail.com> > Date: Tue, 28 Aug 2007 17:39:20 -0500 > To: "General Discussion: On-Topic and Off-Topic Posts" <cctalk at classiccmp.org> > >On 8/27/07, B M <iamvirtual at gmail.com> wrote: >> I am trying to get a Vax-11/750 machine up and running. It looks like the TU58 drive >> is suffering from the 'gooey roller syndrome'. > >Unsurprising. > >> I see that people have successfully used 1/2 inch (ID) Tygon tubing to replace the >> goo. Is there any specific type of Tygon tubing (eg. R3603, R2000, etc.) that is used? > >I don't know the particular variety I used in mine - I just went to >the Lowe's down the street and bought a foot of 1/2" ID tubing - >whatever they had on the shelf. I was unaware of a large amount of >varieties of tubing, so I just used what they had in stock, and it >worked perfectly. > >-ethan I started that many years ago like 1995ish. I spec'd Tygon (brnad name) as that was available to me. Most any generic Vinyl tubing works so long as it fits tight and has enough wall thickness. After about 10 years it tends to get hard, the fix is obvious. Allison

12 years

Wanted: Research Inc. Teleray terminals

by legalize＠xmission.com

I'm looking for more information on the Teleray series of terminals >from Research, Inc. (Note: Teleray is the name of the terminal line, not the name of the company! Although later they referred to themselves as the "Teleray Division" of Research, Inc.) In particular I'm looking for manuals and other documentation. If you have a Teleray terminal and you're looking to get rid of it, I would be interested in purchasing it from you. I know of the following models: Year Model 1971 Teleray 3300 1975 Teleray 3900 1976 Teleray 3811 <1977? Teleray 3541 <1977? Teleray 3741 1977 Teleray 3841 1977 Teleray 4041 1978 Teleray 1061 1979 Teleray 10 1979 Teleray 11 1979 Teleray 12 1980 Teleray 14 <1981? Teleray 100 1982 Teleray 16 1985 Teleray 20-7305 <1990? Teleray 30 Thanks! -- "The Direct3D Graphics Pipeline" -- DirectX 9 version available for download <http://legalizeadulthood.wordpress.com/the-direct3d-graphics-pipeline/> Legalize Adulthood! <http://legalizeadulthood.wordpress.com>

12 years, 1 month

Texas Instruments 960B

by aek＠bitsavers.org

> does anybody have bits for the TI 960B (not 960A) minicomputer, e.g. > software, schematics etc. ? I have some additional material on the 960 that isn't up yet on bitsavers. The 960 and 980 share some peripheral interfaces. Did you end up with the 990 system as well?

12 years, 2 months

HP 9820A

by pye＠mactec.com.au

I was dropping off some rubbish today at the local council dump, and noticed an old HP machine in the trailer next to me. I didn't even say anything, I just stopped and stared at it and the guy asked if I wanted it. When I said yeah, he replied with "shame you weren't a few minutes earlier, I just chucked two others in the recycling bin and all the manuals and tapes/cards are in the pit." Turned out to be an HP 9820A, and I managed to get the other 9820A and a 9810A out of the recycling bin without anyone noticing. Unfortunately couldn't retrieve anything else. Just wondering if there is anything in particular to watch out for when powering up one of these for the first time other than normal power supply checks? I (obviously) don't know much about these machines at all, but I'm particularly mystified about how the built in card reader worked (is it magnetic?).. Could it be written to as well? Cheers, Chris

12 years, 2 months

Prototype PCBs?

by brain＠jbrain.com

Anyone know an inexpensive source for prototype DIY circuit boards? From time to time, I like to use them to prove out ideas, and I'm running low on stock. Jim -- Jim Brain brain at jbrain.com www.jbrain.com

12 years, 3 months

Service bureaus (Was: Tek 4051 firmware listing

by dm561＠torfree.net

Date: Sun, 12 Dec 2010 15:08:12 -0800 From: "Chuck Guzis" <cclist at sydex.com> Subject: Re: Service bureaus (Was: Tek 4051 firmware listing <snip> After that, I learned to drop by keypunch to occasionally chat with the ladies (it was comprised entirely of women), and occasionally drop off some munchies and other things. They knew me and I knew them. And I never had an issue with keypunch after that. --Chuck +++++++++++++++++++++++++++++++++++++++ As a matter of fact my very first job was also in a service bureau and that's where I also learned the importance of being able to charm the ladies, a skill that's served me well (and gotten me into considerable trouble) in subsequent years... mike

12 years, 3 months

Official Spring cleaning sale

by dm561＠torfree.net

----- Original Message: Date: Mon, 16 Apr 2012 08:01:00 -0500 From: John Foust <jfoust at threedee.com> At 05:07 PM 4/15/2012, David Riley wrote: >On Apr 15, 2012, at 1:02 PM, Steven Landon wrote: > >> <loads of crap> > How can this fellow continue scamming, year after year? > - John Well, as he gets banned from one forum/list after another, he just moves on to the next; looks like he's found a home here at last... To his credit some people have apparently bought from him with no issues, but I'd still be wondering if any of the stuff he's flogging now is part of the loot he stole from fellow hobbyists in his prime...

12 years, 3 months

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb May 2012