<It's supposed to be a Panasonic 'block' type battery. A similar battery
<was used in the Portable+, and the service manual for that machine
<clearly shows an assembly of 3 Cyclon cells. So it looks like either
<could be used.
The difference is they are both gelled electrolyte lead acid cells, No
difference. Therefor the working voltages and charing conditions will be
very similar.
SCR based chargers like that will not work if the cells are open circuit or
sulphated (high resistance failure).
Allison
"Peter Pachla" <peter.pachla(a)wintermute.org.uk> wrote:
> No, I wasn't suggesting it didn't - just that for some reason all the ones
> I've ever seen (at radio rallies mostly) have been without the touch
> screen....
By the time of the Touchscreen II, lots of us who had deployed 150A/Bs
had concluded that while the 150 wasn't that bad, touch screens were
not all that they were cracked up to be. You had to take a hand off
the keyboard and reach up and touch the screen, and if you had to do
this a lot it resulted in a sort of fatigue that was called "gorilla
arm", and there were usually ways to do what you wanted from the
keyboard (either a function key or tab around some and then press a
function key or Enter). So most users didn't bother with it after the
novelty wore off.
So when it became an extra-cost option we really couldn't see paying
for it.
Besides, who wants a bunch of fingertip-sized smudges on the screen?
-Frank McConnell
<Well, the obvious chip to use for this application would be an 8-input
<priority encoder like the 74x148. I have no idea if there was ever a 3.3V
<version of this chip, though.
No there wasn't, t was never that commonly used.
As to a chip to do what a simple diode encoder can do is beyond me.
Allison
I'll bet you've gained a real appreciation for DIP or SIP packaged DIODES!
Dick
-----Original Message-----
From: Bill Sudbrink <bill(a)chipware.com>
To: classiccmp(a)classiccmp.org <classiccmp(a)classiccmp.org>
Date: Wednesday, February 23, 2000 8:10 AM
Subject: RE: Diode help... HELP!
>Well... Here's what happens when you make assumptions
>and start to panic.
>
>Turns out the problem was simple. The pins were being
>pulled up to 3.3 not down to ground. All my diodes
>were backwards. Reverse the diodes, problem solved.
>
>Thanks everybody for the help.
>
>Bill
>
- - - - -
Are they any web sites or companies that might be interested in buying
or taking away (for free) a 11/785 that is getting ready to be
unplugged?
tia
Shale(a)sclay.com
- - - - -
I've got an Archive "Viper" 150 MB. data cartridge drive with SCSI
interface, model 2150S, available to the first responder for the cost of
shipping. The drive worked the last time I used it (several years ago), but
there's no warranty. The belt, heads and capstan are unworn and appear in
good condition. This is the drive only--no enclosure or power supply.
If you want them, I also have seven data cartridges. Althrough they
physically fit this drive, they may not all be accepted by the drive's
firmware--I have a half memory that certain drives only worked with certain
cartridges.
If you want this drive and the cartridges, email me your address, desired
method of shipping, and whether you want the cartridges. If I don't hear
anything by Wednesday, it goes up on eBay.
----
John Dykstra jdykstra(a)nortelnetworks.com
Principal Software Architect voice: +1 651 415-1604
Nortel Networks fax: +1 612 932-8549
In einer eMail vom 2/23/100 3:39:04AM, schreiben Sie:
<<
Uh, you don't think they'd let me take this on the plane as carry-on
luggage, huh? I'm going to be in SF on Monday for work...
>>
According to my experience, shipping this beast would be around US$ 1000,-
(within US or to Europe, not counting forwarding within Europe). Not too bad
for a solid item like this, I believe.
John G. Zabolitzy
Munich, Germany
I finally built a rack for my 9track tapes and went through them all. In
addition to what looks like an entire software distribution for my (still
dead) Cadnetix system, I found two VMS tapes, available to anyone
interested:
XDS-11 Base Package
Signetics' Amaze Rev.C Binary (must be an *ancient* version of this,
marked 1985)
Cheers,
Aaron
<Sounds like a job for an IC, like 8 bit parallel to serial using one dip
<switch input for serial data perhaps clocked by sequential reads. Maybe a
<bit binary to octal? 8 bit multiplexer?
He wants to do a diode encode for three switches 8 possible states.
The reverse would be to decode two bits to sense the state of three
switches to be read on a single bit port.
<Sheesh, I shudder to think how many pens are busy on the backs of envelope
<right now.
Only to show what's in my memory. :) That is a textbook circuit.
Allison
Tell the group what you're trying to do, based on your requirements there are several alternatives!
What type of application is this for?
Kevin
On Tue, 22 Feb 2000 16:06:49 -0500 classiccmp(a)classiccmp.org wrote:
> Hi,
>
> Once again demonstrating my vast quantities of ignorance...
> I need a diode which completely blocks current in one direction
> and presents as little resistance in the other direction
> as possible. I bought a fist full of little glass ones at
> Radio Shack for 50 cents. On my Ohm meter, they show no
> conductance in one direction and 1400KOhm the other way.
> What do I need to get? RS (which is the only resource I
> have available, I need them like _NOW_) has many different
> kinds of diodes, ranging up to two dollars per pair.
>
> Thanks,
> Bill Sudbrink