31 Dec
2008
31 Dec
'08
3:33 a.m.
So I finally got the Micro PDP11/53 hooked-up to a terminal. When back at the folks at
over Christmas I found an old MMJ cable and DB25F adapter, which work when the latter is
plugged into the VT. I need to try the MMJ cable I bought recently with this adapter, but
suspect it is something about using an MMJ direct between the PDP and VT. ISTR having this
problem before trying to direct cable a MicroVAX to a VT's MMJ port.
In any case, I'd like to join this machine into Hecnet, hope to run RSTS/E and have a
couple of questions:
- Looks like only v7 of RSTS/E is available, would this suffice?
- Would anyone be willing to help me out with media (happy to cover cost for media and
postage, of course)?
Regards,
Andrew
--
Andrew Back
a at smokebelch.org
31 Dec
31 Dec
8:33 a.m.
I had to check some history for this... the Wikipedia article on RSTS/E
is helpful.
What would you use for a DECnet interface? V7.0 is DECnet Phase II.
Phase III was added in V7.1, but that's still iffy with HECnet, and
you'd need a sync DDCMP interface (for a Q-bus system like that it would
be a DMV11). More to the point, it looks like the Micro-PDP11 support
appeared in V8.0, and I suspect there may be some other small details
specific to the 11/53 that are later still.
For Ethernet (DECnet Phase IV) you'd need V9.3 or later. I don't know
about availability of late releases like that...
paul
-----Original Message-----
From: cctalk-bounces at classiccmp.org [mailto:cctalk-
bounces at classiccmp.org] On Behalf Of Andrew Back
Sent: Wednesday, December 31, 2008 6:33 AM
To: General Discussion: On-Topic and Off-Topic Posts
Subject: RSTS/E question and media.
So I finally got the Micro PDP11/53 hooked-up to a terminal. When back
at the folks at over Christmas I found an old MMJ cable and DB25F
adapter, which work when the latter is plugged into the VT. I need to
try the MMJ cable I bought recently with this adapter, but suspect it
is something about using an MMJ direct between the PDP and VT. ISTR
having this problem before trying to direct cable a MicroVAX to a VT's
MMJ port.
In any case, I'd like to join this machine into Hecnet, hope to run
RSTS/E and have a couple of questions:
- Looks like only v7 of RSTS/E is available, would this suffice?
- Would anyone be willing to help me out with media (happy to cover
cost for media and postage, of course)?
Regards,
Andrew
--
Andrew Back
a at smokebelch.org
8:51 a.m.
On (11:33 31/12/08), Paul Koning wrote:
I had to check some history for this... the Wikipedia
article on RSTS/E
is helpful.
What would you use for a DECnet interface? V7.0 is DECnet Phase II.
Phase III was added in V7.1, but that's still iffy with HECnet, and
you'd need a sync DDCMP interface (for a Q-bus system like that it would
be a DMV11). More to the point, it looks like the Micro-PDP11 support
appeared in V8.0, and I suspect there may be some other small details
specific to the 11/53 that are later still.
Right, so I'd need to plumb the 11/53 into say an Alpha via a serial
connection. Sync... so I'd need to get a PCI sync card too, for the latter.
Ugh.
For Ethernet (DECnet Phase IV) you'd need V9.3 or
later. I don't know
about availability of late releases like that...
Right...
Thanks for the info!
Andrew
--
Andrew Back
a at smokebelch.org
9:38 a.m.
> ...you'd need a sync DDCMP interface (for a
Q-bus system like that
it
would
details
be a DMV11). More to the point, it looks like
the Micro-PDP11
support
> appeared in V8.0, and I suspect there may be some other small specific to
the 11/53 that are later still.
Right, so I'd need to plumb the 11/53 into say an Alpha via a serial
connection. Sync... so I'd need to get a PCI sync card too, for the
latter.
5840
days inactive
5840
days old
3 comments
2 participants
participants (2)
-
andrew＠smokebelch.org -
Paul_Koning＠Dell.com