Noeal asked: the 'warp' use: intermediate You could do it "by eye" in Photoshop and GIMP-type tools, but I believe a far better and more adjustable way is to use an operation in imagemagick called affine transformation. With this you can tweak the result programmatically to the nearest pixel-to-millimetre value to get the best result. For instance I have done an analogous task in which I removed perspective from black and white images of a WWII vehicle onto a flat elevation, so that accurate markings and camouflage patterns or precise positions of fittings can be obtained, by only knowing the basic perimeter edges. To do this, I firstly need an accurate measurement of the side of the vehicle. Its exact length, height will do. This is easily obtained from scale modelling information. In your particular case, I think only the width and height of the panel would be needed, OR the two expressed as a ratio and scaled later. WORKED EXAMPLE: Let's take for example an IBM System/360-40 console. It is comprised of a few individual panels but they are arranged in two larger rectangles, joined along one ege, but with an angle of about 163 degrees between them. The upper panel's flat measurements are 711mm wide and 477mm long. The lower panel is 71mm wide by 199mm high, as flat. Say I then found any sufficiently detailed photo of a /40 console, and wanted to map the surface of that to my known panel edge measurements. The photo is of course taken from any arbitrary angle. I will use this one, 1200x953 pixels, presenting a common three-quarter side view, taken fron the left: https://upload.wikimedia.org/wikipedia/commons/thumb/e/e7/ IBM_System_360_at_USDA.jpg/1200px-IBM_System_360_at_USDA.jpg The angled panels also show in the photo but that will be removed. Save the image locally. I tend to start at the pixel that is the top right corner. The image editor places the origin at the top left corner. Essentially the corners of the console rectangle in the photo - taking the upper panel only, for this example - need to be stretched to my known rectangle of TR=(711,0) to BR= (711,477) to BL=(0,477) to TL=(0,0). The rectangular polygon will automatically be closed back to the start. I'm using mm but you could use any measurement unit you like. Next, load the above photo of the console in any good-enough image editor. I use the free Paint.NET for this purpose and I absolutely love it. Move around the photo, zoom in etc. and place the mouse cursor exactly on the top right corner and take a note of the pixel coordinate shown in the lower right of the app. I make it to be (675,141) on that particular photo. Then do the same for the bottom right, bottom left, top left corner pixels. Remember this is the top panel only, the lower is done in the same fashion seperately. These are done in the same point-to-point sequence as the known measurements, and must be the same number of coordinates. It does not have to be a rectangle, you may have five, six or more coordinates for a say a vehicle or spaceship scale elevation. So directly off the photo: 675,141 TR 646,315 BR 442,336 BL 458,129 TL Now, assuming Imagemagick is installed, all we need to is tell it to stretch those coordinates to our known actual square coordinates by pairing them, pixel-to-known coordinate. On the command line, or in a text file enter and paste into the shell (I use git bash on Windows): convert 1200px-IBM_System_360_at_USDA.jpg -virtual-pixel black -distort Perspective "675,141 711,0 646,315 711,477 442,336 0,477 458,129 0,0" Model40_upper_panel_transformed_true_flat1.jpg Now the required de-perspective image will be in Model40_upper_panel_ transformed_true_flat.jpg If you don't want to go through the above steps yourself you can see the result at http://web.aanet.com.au/~malikoff/ibm/Model40_upper_ panel_transformed_true_flat1.jpg Then use the image editor rubber banding to select the required amount of this true flattened image, now using the original actual measurements as the pixel coordinates for cropping. eg. TR edge is pixel (711,0) etc. If the simple Perspective operation doesn't gove you a good result, try some other Imagemagick operations eg: convert 1200px-IBM_System_360_at_USDA.jpg -virtual-pixel black -interpolate Spline -distort BilinearForward "675,141 711,0 646,315 711,477 442,336 0,477 458,129 0,0" Model40_upper_panel_ transformed_true_flat2.jpg this result #2 at http://web.aanet.com.au/~malikoff/ibm/Model40_upper_ panel_transformed_true_flat2.jpg although I tend to find the Perspective does a better job. There is plenty of help on the imagemagick.org site and also Stack Overflow., such as https://stackoverflow.com/questions/12276098/ understanding-perspective-projection-distortion-imagemagick Further post-processing for me would be to then load this 711x477 image as the background image layer in CAD where it is fitted to a rectangle of the same size, in actual mm real world dimensions. I can then overdraw all manner of lines, construction lines, circles and other drawing elements to get a near-perfect actual CAD drawing. Every so often I just hide the background layer to see how it looks, and bits I've missed. Sorry about the long blurb but hope it can help you on your panel. Steve.