23 Jan
2006
23 Jan
'06
9:47 a.m.
From: ard at p850ug1.demon.co.uk
Hi
My personal opinion is that the drum absorbs some moisture
and toner tends to stick to it in a non-static way. On my machine
it didn't happen when I was using it regularly but after
some non-use in the winter time. The new drum works fine.
It had the same problem. Right after turning on I'd get maybe
two sheets printed before streaks would start to build up.
Visual inspection of the drum showed toner remaining on
the drum.
I still have the old toner box and I've though of removing
the drum and baking it for a while in the oven to see if it
recovers. The toner is about half full. One can't bake both
or the toner might turn into a lump. One would have to remove
the drum. I've had one of these apart once and they are a
little tricky to get apart but it can be done.
Dwight
I had exactly the same problems with my 5M and
after doing almost
everything I could think of I finally read the manual (please don't
quote me here :-). Turned out this symptom is most commonly fixed by
replacing the toner cartridge which (perhaps not so surprisingly)
fixed the problem.
It would be interesting to know what went wrong with the old cartridge.
Is it that the drum is damaged in some way and doesn't discharge
properly usder the erasing lamps? Or is it that the wiper blade doesn't
clean the surface of the drum properly? Or what?
-tony 
23 Jan
23 Jan
10:09 a.m.
In article <200601231747.JAA13413 at ca2h0430.amd.com>,
"Dwight Elvey" <dwight.elvey at amd.com> writes:
My personal opinion is that the drum absorbs some
moisture
and toner tends to stick to it in a non-static way. [...]
I live in the desert and use my printer fairly often and I've had this
problem.
--
"The Direct3D Graphics Pipeline"-- code samples, sample chapter, FAQ:
<http://www.xmission.com/~legalize/book/>
Pilgrimage: Utah's annual demoparty
<http://pilgrimage.scene.org>
10:12 a.m.
Since we're talking about streaky printing, my LaserWriter 16/600 PS (LaserJet
4 engine) is doing its second set of printing an irregular black pattern down
one side of a page. The remainder of the page is normal.
Replacing the toner cartridge fixed this for awhile and it's doing it again.
Agitating the cartridge to loosen up any toner piles didn't make much change.
Before I go buy another toner cartridge, anything to check? They're not all
that expensive but it is annoying if it's something correctable.
By the way, have people noticed that laser paper no longer has sides? This
printer insists on sided paper. If I load the wrong side up, it will jam.
But the laser paper sold in Office Depot and so on no longer has sides, so
I'm not sure where the curl is to load it properly.
--
--------------------------------- personal: http://www.armory.com/~spectre/ ---
Cameron Kaiser * Floodgap Systems * www.floodgap.com * ckaiser at floodgap.com
-- Remember, Windows is not a virus. Viruses actually do something. -----------
10:38 a.m.
In article <200601231812.KAA20200 at floodgap.com>,
Cameron Kaiser <spectre at floodgap.com> writes:
By the way, have people noticed that laser paper no
longer has sides? This
printer insists on sided paper. If I load the wrong side up, it will jam.
But the laser paper sold in Office Depot and so on no longer has sides, so
I'm not sure where the curl is to load it properly.
The last time I bought paper, it still had a marking on the wrapper
saying this side up, but that was a while ago.
--
"The Direct3D Graphics Pipeline"-- code samples, sample chapter, FAQ:
<http://www.xmission.com/~legalize/book/>
Pilgrimage: Utah's annual demoparty
<http://pilgrimage.scene.org>
6909
days inactive
6909
days old
3 comments
3 participants
participants (3)
-
dwight.elvey＠amd.com -
legalize＠xmission.com -
spectre＠floodgap.com