Hi
I'm sure McMaster-Carr has them but of the original
group he stated also had them. He was just looking under
the wrong name. He should have been looking for standoffs
or spacers. The digikey catalog on my lap has them indexed
as Harware/Spacers/Standoffs.
As a general rule, any hardware that McMaster-Carr doesn't
have just plan doesn't exist.
Dwight
>From: "Don North" <ak6dn at mindspring.com>
>
>Try this place: http://www.mcmaster.com/ ... under the section
>FASTENING AND SEALING click SPACERS.
>
>If they don't have it, it does not exist, and you will have to make it
>yourself.
>
>>> Hi -
>>> I searched for card separators on Digikey, Code Micro, or Jameco (some
>>> people call them "risers.") - no specific luck. I have emailed them for
>>> assistance. In the mean time...
>>>
>>> As I wrote before I am trying to install a small computer board on top of a
>>> computer motherboard, so that the smaller board is about 9/16" separated
>>> from the motherboard. There is not much clearance and I want to just make
>>> it a few hairs above the IC's on the motherboard or I can't close the lid
>>> of the computer. There are holes in both boards that line up for the
>>> risers (the small board is made to be attached to the motherboard with
>>> risers). My local Radio Shack's card separators/risers are either too
>>> short or too tall.
>>>
>
This was back, oh, in about 1978. I was at one of the trade shows (don't
remember which one) and there was a fellow with a computer with integrated
monitor, disk drives and a printer (sticking out of the top) in a fairly
large black box--probably Z80, but I can't be sure.
I remember that it was USR because of the unusual name of the company. Has
anyone else ever seen one of these beasts?
Cheers,
Chuck
Hi -
I searched for card separators on Digikey, Code Micro, or Jameco (some
people call them "risers.") - no specific luck. I have emailed them for
assistance. In the mean time...
As I wrote before I am trying to install a small computer board on top of a
computer motherboard, so that the smaller board is about 9/16" separated
>from the motherboard. There is not much clearance and I want to just make
it a few hairs above the IC's on the motherboard or I can't close the lid
of the computer. There are holes in both boards that line up for the
risers (the small board is made to be attached to the motherboard with
risers). My local Radio Shack's card separators/risers are either too
short or too tall.
The card separators/risers have screw holes on either end so that you can
fasten them to the boards.
Does anyone in this group have four 9/16" risers that they'd like to sell
or trade me? I actually found two in my supplies, but I need four of the
same height. If anyone would like a picture to get a better idea of what I
need, let me know via private email.
Bill Degnan
>From: "Lance Lyon" <lance.w.lyon at gmail.com>
>
>From: "Dwight Elvey" <dwight.elvey at amd.com>
>
>> Most shill's can be noticed by looking at the buyers records.
>> If they have a lot of buying from the same seller, it is a good
>> chance that they are a shill.
>
>Not always the case, I sell quite a bit of Commodore equipment & I have
>regular buyers (in fact one guy has bought 28 items from me in the last four
>years). In the same vein, there are sellers that I have bought many items
>off because they have what I want, and they are reliable.
>
>The statement is way too broad.
>
>cheers,
>
>Lance
>
>// http://landover.no-ip.com
> Classic machines, classic software //
>
Hi
I would suspect that those buyer also buys from many others.
I meant that the buyer only buys from one seller and buys
many types of items. I doubt this is the case
you have mentioned.
Dwight
Hey, so I'm glad that I read a web page (can't remember the URL,
sorry... linked from the Nike Missile site, I think) about
refurbishing deteriorated parts in old machines. I bought a 2648A
main unit (would love a keyboard for it, if anyone has an extra) and
opened it up last night. The tape drive capstans have turned to a
puddle of goo! So I figure that if I ever want the tape drive to be
in working order, that I need to:
i) remove the goo
ii) recreate/replace the capstan
Does anyone have a unit with an intact capstan that could give me
physical dimensions? I doubt anyone has a repair kit that would
include the capstan, but that would certainly be welcome! Aside from
the capstans and a little dust inside the case, the internals look
fine. The case has a small crack in one corner, but otherwise appears
in typical condition for its age. This thing is basically a
microcomputer... when I used them back in 1979, I had no idea that
there was this much electronics inside the thing!
I do have the user manual from bitsavers, but it doesn't go into
repair stuff, just installation (which is how I figured out how to
open the case) of options.
As always... thanks!
--
"The Direct3D Graphics Pipeline"-- code samples, sample chapter, FAQ:
<http://www.xmission.com/~legalize/book/>
Pilgrimage: Utah's annual demoparty
<http://pilgrimage.scene.org>
>From: "Dan" <ragooman at comcast.net>
>
>Lurker here,
>
>Just keep in mind that as with any other business(and auctions) there's
>always a shill to artificially inflate the bidding for an auction. eBay
>is notorious for this as they have absolutely no precautions(nor
>security) against this. I know because I've found how this done very
>easily, anyone who has access to internet can do this. The seller can
>easily just as well have numerous eBay screenames/accounts and bid
>against his own auction to drive up the price(and act as his own shill).
>So what looks like an act of stupidity is easily just a ploy by the
>shill to aggravate you into bidding more for his/their product. eBay has
>no type of screening whatsoever to prevent this type of thievery. Just
>be forewarned.
>
>=Dan
>
>
---snip---
Hi
Most shill's can be noticed by looking at the buyers records.
If they have a lot of buying from the same seller, it is a good
chance that they are a shill. Also a quick check of the sellers
feedback will often find several shill names.
Ebay doesn't seem to do much more than warn the seller when
they are notified. This is even when it is obvious shilling.
Dwight
{The Design of OS/2} by Deitel and Kogan (how do you delineate titles of books when you can't underline or italicize?) seems to indicate that the triple fault switch back to real mode is relying on a "feature" of the 80286, since for the reset method it talks about the hardware involved (keyboard controller on AT, I/O port electonics on PS/2). The book also makes the note that "compared ot the other alternatives, the process [triple faulting] is a slow one" (285).
Hi
These are usually called standoffs. Digikey has many types
and sizes. Give me material and thread sizes and I can
give you a digikey part number.
Dwight
>From: "B. Degnan" <billdeg at degnanco.com>
>
>Hi -
>I searched for card separators on Digikey, Code Micro, or Jameco (some
>people call them "risers.") - no specific luck. I have emailed them for
>assistance. In the mean time...
>
>As I wrote before I am trying to install a small computer board on top of a
>computer motherboard, so that the smaller board is about 9/16" separated
>from the motherboard. There is not much clearance and I want to just make
>it a few hairs above the IC's on the motherboard or I can't close the lid
>of the computer. There are holes in both boards that line up for the
>risers (the small board is made to be attached to the motherboard with
>risers). My local Radio Shack's card separators/risers are either too
>short or too tall.
>
>The card separators/risers have screw holes on either end so that you can
>fasten them to the boards.
>
>Does anyone in this group have four 9/16" risers that they'd like to sell
>or trade me? I actually found two in my supplies, but I need four of the
>same height. If anyone would like a picture to get a better idea of what I
>need, let me know via private email.
>
>Bill Degnan
>
>