Hi -
I just stumbled upon your posting (at http://www.classiccmp.org/pipermail/cctech/2002-December/006703.html ) from last year - can you tell me if you had any other occurrences of this, or if you had any other responses beyond those linked to your post? Our fire protection engineers tell me this has been a bit of a problem, but I am not finding much information as I look into it for a class project. Did your local fire department respond to the three you mentioned, and was there an investigation / report? Thanks -
Mike
Mike Holder
Boeing Fire Inspection
(206) 544-7950
(206) 416-2020 pager
(P.S. - Would you have saved the faulty suppressors by chance? I'd be very interested in seeing one - or more!.... MH)
Forwarded message:
> From: jim <jwstephens(a)msm.umr.edu>
>
> Robert Krten wrote:
>
> > If I deposit 7777, I can examine and get 3777. This machine has 8k of
> > core, and the problem is the same in both 4k banks.
> > Cheers,
> > -RK
>
> when you read memory, are here any locations where you get back a 1 bit
> in this position from residual junk data in the core?
Nope, unfortunately. I've been running "junk programs" and it looks like
they scribbled all over memory; I looked through the first thousand or
so memory locations, hoping for a 4000 bit, but no luck :-(
> might be a clue what is wrong with deposit vs rad.
>
> can you examine other registers from the front panel and change that bit, or
> is it just the core?
No other registers are accessible from the front panel -- you're think of the
PDP-11 :-)
> if you can examine the registers, IIRC, can you put a program in there to load
> a constant and deposit it in core? This would exercise a different path to the
> core, though I know that the front panel is probbly doing a step to do the
> deposit.
>
> I may be crossing wires with the pdp11 as far as the registers being
> addressible in
> memory, if so I apologize, it's been a long time, and I have no handy manual to
> verify
> this for you.
No problemo; appreciate any help I can get :-)
Cheers,
-RK
--
Robert Krten, PARSE Software Devices +1 613 599 8316.
Realtime Systems Architecture, Consulting and Training at www.parse.com
Looking for Digital Equipment Corp. PDP-1 through PDP-15 minicomputers!
don't do the dry/sanitize cycle ! or you may get a Salvador Dali case
when you are done.
-----Original Message-----
From: Ernest [mailto:ernestls@attbi.com]
Sent: Wednesday, November 05, 2003 10:05 AM
To: 'General Discussion: On-Topic and Off-Topic Posts'
Subject: RE: Any suggestions for cleaning yellowed computer parts?
> A run through the dishwasher sometimes helps (note: sometimes).
Yes. Beware on this sometimes, too. I ran a Coco-3 case through the
washer and it cleaned the case very well but it also washed out the
colors on the label. Now, the case and label have a uniform washed out
look to them. Also, I've noticed that sometimes, running a case through
the dishwasher doesn't always clean thick grime off. It only bleaches it
so that it looks like it's gone, and the drying heat can bake and harden
the grease so that it's more difficult to remove.
I still prefer to use a sink full of hot soapy water, and a medium stiff
paint brush, and lots of elbow grease. The brush gets down into the
cracks and crevasses, and any texturing on the case. I also prefer this
method because I enjoy the act of scrubbing everything up. I like to see
the cleaned piece emerge from years grime and dirt, and the work gives
me time to think. A toothbrush and a facial buff pad are also useful.
Short of painting, there is no way to restore a sun damaged case that
I've found. I have nothing against painting an old computer case, since
many of them were painted to begin with -even the plastic case were
often painted.
Does anyone have a secret recipe that is *safe* for cleaning
yellowed/stained plastic computer parts that were originally white? I have
had some success with various cleaning agents, but nothing spectacular.
-bill
wilmington, delaware
Hiyas,
Yay! Today wasa good day... besides having (finally) collected
some of the VAXen I was supposed to pick up last week, I also got
around to grabbing the LA424 I bought online.
Nice printer! Came with everything included, *including* the
DS200/DL they were using as a printerserver :) and the VT420
which was its console. Also, a (still sealed) box with ribbons.
Now.. to find its manual. Anyone?
(oheyah, and a box of wide fanfold ;-)
Cheers,
Fred
--
Fred N. van Kempen, DEC (Digital Equipment Corporation) Collector/Archivist
Visit the VAXlab Project at http://www.pdp11.nl/VAXlab/
Visit the Archives at http://www.pdp11.nl/
Email: waltje(a)pdp11.nl BUSSUM, THE NETHERLANDS / Sunnyvale, CA, USA
How many of us clicked the link "This link is broken "
just to see ... now that's geeky!
- Henk (just a "geek" with 17.xxxxx% :-(
> -----Original Message-----
> From: David Woyciesjes [mailto:dwoyciesjes@comcast.net]
> Sent: dinsdag 4 november 2003 20:20
> To: ClassicCMP
> Subject: The Geek Test...
>
>
> How many of you have seen this one?
> http://www.innergeek.us/geek.html
>
> I only got a 7.88955% result...
>
> --
> --- Dave Woyciesjes
> --- ICQ# 905818