Way off topic here, and rantish to boot, but just to give y'all a heads up
- Don't install Internet Explorer 5. Bunches of reasons, but my big one is
this:
If you are ill advised enough to uninstall explorer 4, you *can't* get 5
off your system. And at least when I tried it has destabilized my system
to the point my desktop crashes about every 10 minutes. I'll be migrating
to BeOS as soon as they mail my copy to me. *grumble*
On the other hand, and considerably more on topic, the new hobbiest media
for openVMS is supposedly going to be available on the 18th of this month from
http://www.montagar.com/hobbyist/media.html.
--
Jim Strickland
jim(a)DIESPAMMERSCUMcalico.litterbox.com
-----------------------------------------------------------------------
Vote Meadocrat! Bill and Opus in 2000 - Who ELSE is there?
-----------------------------------------------------------------------
I have four 8080 computer systems to dispose of.
They were used in a dedicated industrial application - not as a readily reprogrammable system. Some of the chips may however be of use to someone - preferably someone who can collect from Chatswood, Sydney Australia.
The main chips are (I am only listing chips in sockets)
4 off 8080A
about 200 dynamic memory chips. some are marked 4030, others 4060. they are also referred to as 2107B-4 in the documentation.
about 25 eproms type 1702A
about 12 off 8212 i/o port chips
about 30 off chips marked SN74S412. I cannot find this in my old data book but from the circuit they appear to be doing the same job as 8212
Also available are Intel data catalogues from 1976 and 1977 and a Signetics Bipolar and Mos memory databook dated 1977
David
Is anybody interested in a copy of a kermit-11 user manual dated 1985
I don't have the software just the manual.
Kermit-11 is a file transfer program that runs under RT-11 and posibly other PDP11 systems such as RSTS, RSX, TSX
David
At 17:17 15/05/99 +1, Hans wrote:
>> >I just picked up a Copmaq Portable PLUS (DM 35), a
>> >Portable III (DM 40),
>> >Is there any site with information on the Compaq Portabele III ?
Yesterday and today I "lived" inside the pavillions of Forli' expocenter
where every year take place the Easter Hamfest.
I have also picked a Compaq Portable II at 26 Eu (abt.27 U$D)
It's a 8086 luggable machine with CRT -> VERY HEAVY!
I've also picked:
-WISE WY 3216-40 (@ 15 EU no monitor)It's a 386 with the processor and the
RAM mounted in two different ISA cards, linked thru a upper connector. The
keyboard is the classical WY 160 grey terminal keyboard with mmj connector.
The system has a nice LCD retro-illuminated display and a big Megnetic
Peripherals MFM (noisy) disk that reached the edge of his days.
-C=ommodore PC 20 III (@ only 13 EU, no monitor) mint conditions 3,5 fdd
probably a 286.
-Some printers (bought not as vintage machines)
- HP 320, HP520 (both @ 57 EU)
- 2x Epson FX850 @ 35 EU each (they were used by REUTERS somewhere)
The man that sold me the Wyse has also a Mannesmann Tally 8 bit optical tape
reader @62 EU.
I saw a very similar device inside a frontpanel of a automatic plasma
welding machine
as a numeric controller.
I have taken a picture with my digital camera and I will put it on a webpage
someday
(I just started a HTML/Frontpage course this week)
The reader was new inside its carton box and the man told that he still have
15 available.
Another couple of yummy think I've seen where a Sinclair ZX 81 and a TIMEX 1000
The bad new where the prices (please seat safetly): 150 EU the first :(
and abt. 220 EU the second!!! :o
>P.S.: and speaking of today, new members of my junk yard are:
snip!
>Olivetti CTV 250 Typewriter/Textprocessor (back in the 80s, Olivetti
>had the most impressive design, not just grey boxes - I still would
>love to get hands on one of these small BASIC able 'handheld' systems
>as they where in unse in a lot of Cambio (Money Change) shops - top
>notch design and a cute interior)
BASIC "handeld"?
can you explain more about that? you mean the P.O.S./BANCOMAT small units
with thermal printer?
In case you like that kind of Oilvetti design, it's possible to contact many
wharehouse near Ivrea that stocks also new machines, E.G. the TE550 teletype
machine that I've bought new @ 92 EU while 3 years ago it was sold to the
National Postal Service @ abt. 2500 EU!! ;D
Ciao
Riccardo Romagnoli
<chemif(a)mbox.queen.it>
I-47100 Forl?
<I can repair the RAM 16 A3 but I don't have the switch settings and
<jumper settings (J) to set it to start at 2000H. What are these?
Is that a NS ram 16? I have a mod of the MDS-A3 (SD) controller to put
Phantom/ on the bus. However the card has to respect it.
The address hole needed for the controller is from E800 thru EFFFh.
<Also, I have a RAM 16 A2 board that I can try. Are the switch settings
<and the jumper settings on it the same as the A3 to start at location
<2000H?
Dont ahve them for that card. Never used any of the NS* ram cards.
<Finally, will NSDOS run in 16K ram? I see no indication in the manuals
<that it won't but it's a good question to ask anyway.
NSdos runs fine in 8k! the dos is d00H (DD 3328) or a00(SD 2560) large and
starts at 2000. Basic however does fit in 16k but barely.
So happens I'm resurecting a NS*Horizon I got a few weeks back. Mine is
however working just fine once I set up the serial for my standard setup
and to match the Horizon I've had for 21 years.
Allison
On Sun, 16 May 1999, Ethan Dicks wrote:
________O/_______
O\
> P.S. - where's a good place to get a Kaypro boot disk? I have a licensed
> copy of teledisk so I should be able to make them from bits, yes?
E-mail me the EPROM number(s) that are on a paper label on the chip and I
can send a TeleDisk image to you.
- don
donm(a)cts.com
*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*
Don Maslin - Keeper of the Dina-SIG CP/M System Disk Archives
Chairman, Dina-SIG of the San Diego Computer Society
Clinging tenaciously to the trailing edge of technology.
Sysop - Elephant's Graveyard (CP/M) Z-Node 9 - 619-454-8412
*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*--*
see old system support at http://www.psyber.com/~tcj/
visit the "Unofficial" CP/M Web site at http://www.devili.iki.fi/cpm/
with Mirror at http://www.mathcs.emory.edu/~cfs/cpm/
<the /usr subtree. The remaining files under "/" take up around 10-12Megs,
<then you'll also need separate swap files which adds another X Megs per
<machine. You can probably get by with more of the setup being shared, but
Has anyone considered the hack that is done under VMS for small disk impared
systems? IE: net or local boot, local swap everything else from
the net host. Then the seap drive can be a small 20-40mb drive and the
swapping is faster if local even with PIO. that would yeild a fairly fast
system that wouldn't beat teh disks to death on the host.
Allison
--- Chuck McManis <cmcmanis(a)mcmanis.com> wrote:
> Ethan Dicks wrote:
> > I'm very familiar with them; I wrote the LCDProc driver for the B.G.Micro
> > "PIC-an-LCD" serial<->LCD adapter chip.
>
> I did some further research on them and these Optrex LCDs have an LED
> backlight, are 160 x 128 can be run in graphics mode...
Fancy. I would have loved to have seen graphical LCDs. I've only had
the text-mode (with programmable characters) to play with. Have you been
to the LCDProc site? (lcdproc.omnipotent.net) It's the one that I'm most
familiar with, and is very well along the development chain.
> I'm pretty excited. I went back on Saturday and they were all gone (doh!)
> So I've only go the two.
Bummer.
-ethan
_____________________________________________________________
Do You Yahoo!?
Free instant messaging and more at http://messenger.yahoo.com
On May 16, 16:22, Tony Duell wrote:
> [BBC power supplies]
> I'd love to see circuits for all the versions, or at least circuit
> descriptions. On the other hand, Acorn PSU schematics are generally hard
> to find for some odd reason.
I never saw schematics for any of the black ones; I've got the diagram for
the Astec as you know. I once did have a note of what the chopper was --
or rather, I had a part number that worked. I worked for Computer Field
Maintenance for a while, and we used to repair them (though they didn't
actually fail very often. They seem to be pretty robust). BSR made a copy
under license, but the BSR ones don't seem to be so good -- not so well
regulated, for a start, so not so tolerant of overloads.
> All my Beebs have the traditional Astec SMPSUs. BTW, does anyone know
> what the chopper transistor is in these units? It's the same in virtually
> all Astec supplies - a TO3 can on a small PCB/heatsink mounted at right
> angles to the main board. There is never a number on it.
All I can remember is that it's NPN, I think. I'll dig through some old
files if I can figure out a way to read the old winchester backups, and
see...
--
Pete Peter Turnbull
Dept. of Computer Science
University of York