16 Nov
2005
16 Nov
'05
4:03 a.m.
Subject: Re: PDP-11/73 booting!
From: David Betz <dbetz at xlisper.mv.com>
Date: Tue, 15 Nov 2005 22:32:43 -0500
To: "General Discussion: On-Topic and Off-Topic Posts" <cctalk at
classiccmp.org>
Yes, you're right. I did type DL not RL. That was a typo in my
message. Yes, the DL.SYS driver is on the boot disk (RX02), there are
no empty slots between the CPU and the RL controller. The slots are
filled as follows:
KDJ11-A
MSV11-LK
MSV11-LK
National Semiconductor memory board (1mb)
RLV12
M8029 (RX02 controller)
MXV11
I'd pull the MXV11 and the National card them bump every one up.
No fault light (and it isn't burned out), the white
load light (with
the "0" on it) lights.
Thats a good sign.
So, I suppose that means that the cables are probably
bad? BTW, I
have the cable plugged into the top connector on the RL01 and the
terminator on the bottom. Is that correct?
I don't think which is which matters as it's a parallel pass through
and the drive select plug is the determining factor.
From RT-11 a
show dev:
or
Resorc /A
Should list the devices the system knows of. It may be possible that
one of the cards is not passing intgrant. If the system doesnt show
the RL02 either grant chain is broken or the controller is not there.
Which controller? Two board set or later single board m8061 one?
The controller (RLV12) must be address at 17774400 (q22), 774400 (q18).
The vector is 160.
Allison
16 Nov
16 Nov
4:08 a.m.
I can't pull the MXV11 because it has the bootstrap and my console
port. I did try it without the NS memory board but that didn't work
either. In fact, RT-11 seems happy with that board as it reports the
correct total amount of memory (1.5mb). I have the single quad board
RL01/02 controller.
Here's the result of "SH DEV":
.SH DEV
Device Status CSR Vector(s)
------ ------ --- ---------
DY Resident 177170 264
LD Installed 000000 000
SL Installed 000000 000
VM Installed 177572 250
NL Installed 000000 000
DL Installed 174400 160
On Nov 15, 2005, at 11:03 PM, Allison wrote:
Subject: Re: PDP-11/73 booting!
From: David Betz <dbetz at xlisper.mv.com>
Date: Tue, 15 Nov 2005 22:32:43 -0500
To: "General Discussion: On-Topic and Off-Topic Posts"
<cctalk at classiccmp.org>
Yes, you're right. I did type DL not RL. That was a typo in my
message. Yes, the DL.SYS driver is on the boot disk (RX02), there are
no empty slots between the CPU and the RL controller. The slots are
filled as follows:
KDJ11-A
MSV11-LK
MSV11-LK
National Semiconductor memory board (1mb)
RLV12
M8029 (RX02 controller)
MXV11
I'd pull the MXV11 and the National card them bump every one up.
No fault light (and it isn't burned out), the
white load light (with
the "0" on it) lights.
Thats a good sign.
So, I suppose that means that the cables are
probably bad? BTW, I
have the cable plugged into the top connector on the RL01 and the
terminator on the bottom. Is that correct?
I don't think which is which matters as it's a parallel pass through
and the drive select plug is the determining factor.
From RT-11 a
show dev:
or
Resorc /A
Should list the devices the system knows of. It may be possible that
one of the cards is not passing intgrant. If the system doesnt show
the RL02 either grant chain is broken or the controller is not there.
Which controller? Two board set or later single board m8061 one?
The controller (RLV12) must be address at 17774400 (q22), 774400
(q18).
The vector is 160.
Allison
6993
days inactive
6993
days old
1 comments
2 participants
participants (2)
-
ajp166＠bellatlantic.net -
dbetz＠xlisper.mv.com