26 Feb
2002
26 Feb
'02
6:28 p.m.
On Feb 26, 13:41, Tom Leffingwell wrote:
The first message I normally see is RT-11 loading...I never have to do
anything, it just boots from DY0:. If I don't have a disk in, or its
messed up for whatever reason, I get:
173326
@
I looked a little closer inside the unit, and it doesn't seem to have a
belt. There's a worm actuator that shakes when on power up when it tries
to move back to its starting place. It can be moved by hand easily, so
it doesn't seem to be binding.
That's the head positioner leadscrew. On powerup or a Bus Init, it should
move back to track zero (maybe only if there's a disk in ithe drive,
depending on the controller). The drive belt is on the underside of the
drive. They often fall off.
A quick way to test if the drive is turning, is to take a floppy, trun the
disk in the jacket until the sector hole is visible in the round hoe in the
jacket, put it in the drive, close the door, open the door, take the disk
out, and see if the sector hole is still visible. Most 8" drives rotate
all the time, so closing the door (which clamps the disk to the spindle)
should turn it. The odds of the sector hole ending up in exactly the same
place after this are minimal. It doesn't tell you if the drive is running
at the correct speed, but it will tell you if it's not turning at all.
If not, the most common causes are that the drive belt has slipped off the
pulley, or that the plastic collet which clamps the disk has broken and
isn't clamping, or not well enough.
--
Pete Peter Turnbull
Network Manager
University of York
27 Feb
27 Feb
1:48 a.m.
On Wed, 27 Feb 2002, Pete Turnbull wrote:
That's the head positioner leadscrew. On powerup
or a Bus Init, it should
move back to track zero (maybe only if there's a disk in ithe drive,
depending on the controller). The drive belt is on the underside of the
drive. They often fall off.
It does look like it wants to go back to track zero. If I manually line
it up just right, it will power up correctly, but as soon as it wants to
go somewhere, the problem starts over. Meanwhile, the other drive lines
itself up just fine.
A quick way to test if the drive is turning, is to
take a floppy, trun the
disk in the jacket until the sector hole is visible in the round hoe in the
jacket, put it in the drive, close the door, open the door, take the disk
out, and see if the sector hole is still visible. Most 8" drives rotate
all the time, so closing the door (which clamps the disk to the spindle)
should turn it. The odds of the sector hole ending up in exactly the same
place after this are minimal. It doesn't tell you if the drive is running
at the correct speed, but it will tell you if it's not turning at all.
I could easily see the disk turning with the cover off of the unit. I
guess I can't verify the speed, but I don't think that's the problem,
because I can't even get far enough to attempt to read something. When
the unit powers up, it detects the problem when it tries to move to track
0 (with or without a disk), and then then LED on the front just flashes,
at which point it won't do anything unless you power cycle it.
There are several LEDs inside the case that light up. Does anyone have
docs for this thing that might be able to look them up?
If not, the most common causes are that the drive belt
has slipped off the
pulley, or that the plastic collet which clamps the disk has broken and
isn't clamping, or not well enough.
--
Pete Peter Turnbull
Network Manager
University of York
6:52 a.m.
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 1333 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/20020227/d2b59750/at…
8286
days inactive
8286
days old
2 comments
3 participants
participants (3)
-
ard＠p850ug1.demon.co.uk -
pete＠dunnington.u-net.com -
tom＠sba.miami.edu