23 Aug
1997
23 Aug
'97
6:51 a.m.
This is getting to be a real pain...
Sometimes it boots, most times it won't. Usual response is I say
b du
or
b du0
It hits the disk twice, and halts at 050110. I have run the RA down all
it's diags in the manual, no faults. Same for when it boots. The UDA50
does running lights too. Doesn't matter if I use A or B. Only difference
there is A lights up sometimes and B doesn't. Cables look fine. What's
going on? Does it just hate me?
Also, when RSTS/E does come up, it sometimes traps to 4.
Timeout/sysfail vector. Something says this drive is going...
23 Aug
23 Aug
8:34 a.m.
New subject: RA81 Rides Again! More problems.u
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 947 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970823/700f9bb9/at…
8:07 a.m.
New subject: RA81 Rides Again! More problems.u
On Sat, 23 Aug 1997, Tim Shoppa wrote:
Time to get down to basics: what boards are in this system? How
are they configured? Which version of RSTS/E?
And we're off!
Every little bit I can come up with.
The system is in two cabinets. Two BA11s.
I have an RA81 for the boot drive, two TU58s in the main cabinet, the
console terminal (A Wyse 30 for now), and a real funny plug in the system
case. 3 rows of wires in a printer-style plug. LP11?
BA11 #1:
This is the system box, BTW. The one whose power cord I hacked up.
The DEC power cord is 120VAC, 1 phase, etc etc. But it has a sideways
pin. So I whacked the end off a PC cable, soldered the appropriate pin to
the appropriate wire, and plugged her in. It worked.
The power controller plug was too wierd to mess with.
Slot
1 M7090
2 Empty
3 M7093
4 M7094
5 M7095
6 M7096
7 M7097
8 M7098
9 M8743 BF
10 M8722 BB
11 M8722 BB
12 M8722 BC
13 Grant Contnuity jumper
14 M9202 and GCJ
15 other end of M9202 and GCJ
16 M8719
17 M8719
18 M7258
19 M7297 and M7296
20 Unlabled
21 Same
22 M5904
23 M5904
24 M5904
25 GCJ
26 M9300 and GCJ
27 Bus extender ribbons and GCJ
Raised the BA11 and checked out the backplane. Looks fine.
BA11 #2
1 Other end of bus extender and GCJ
2 M8719
3 M8719
4 M920 and GCJ
5 Other end and M7297 and M7296
6 M7295
7 M7294
8 M5904
9 M5904
10 M5904
11 M9300 and GCJ
12 M9300 and GCJ
13 M9202 and GCJ
14 other end and GCJ
15 M7486
16 M7485
17 GCJ
RSTS/E is *extremely* picky about configuration
details. If some boards have been pulled and/or added without
carefully following the rules about ordering CSR's and vectors, it's
not surprising that RSTS/E falls and can't get up.
Not even booting? And when it does boot, I get
LP0: device not interrupting - disabled
or something like that
10:32 a.m.
New subject: RA81 Rides Again! More problems.u
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 1710 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970823/217467d8/at…
9:36 a.m.
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 669 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970823/3c96806d/at…
4:35 p.m.
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 1687 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970823/748f6ae2/at…
24 Aug
24 Aug
9:48 a.m.
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 2396 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970824/b05bcff7/at…
23 Aug
23 Aug
9:48 a.m.
New subject: RA81 Rides Again! More problems.u
1. You've got two RH11's in the system, but
(as far as I can tell)
you've got no Massbus peripherals. Why not pull the RH11 system units?
Okay. I'd like to trim this down to one cabinet anyway.
2. Why is there no Unibus terminator at the end of the bus? (Or
did you just leave it out?)
Oh, crap. There's the problem?
3. Are the M9300's sitting in RH11 system units?
Just looking
at your list above, I can't see why they'd be in the middle of the
Unibus at all. M9300's are terminators, and unless there's a very
special reason, they generally are only at the end of the bus.
Not sure, I stuck one on the end of the bus - everything started working!
Generally, I think it'd be wise to pull all the unused cruft (esp RH11's!)
and get the entire system in one box.
"Not Interrupting" to me often indicates a problem with interrupt
continuity. And if the interrupts aren't getting through, it's
extremely surprising that any DMA to your RA81's is being done
at all...
Now it didn't.
Apparently, someone moved some terminators around. Looks fine now!
Tim.
11:15 a.m.
New subject: RA81 Rides Again! More problems.u
A non-text attachment was scrubbed...
Name: not available
Type: text
Size: 1566 bytes
Desc: not available
Url :
http://www.classiccmp.org/pipermail/cctalk/attachments/19970823/747d8953/at…
9982
days inactive
9983
days old
8 comments
3 participants
participants (3)
-
ard＠p850ug1.demon.co.uk -
dseagrav＠bsdserver.tek-star.net -
shoppa＠alph02.triumf.ca