the time was hacking PDP-11 assembler on an 11/23. The basement would routinely get to +40F, and sometimes colder if the wind was from the right direction (the water pipes had electric wraps). I couldn't personally stand to work in that environment without a heater pointed at me, but the computers ran fine. The lone device that had problems

The basement would routinely get to +40F, and sometimes colder if the wind was from the right direction (the water pipes had electric wraps). I couldn't personally stand to work in that environment without a heater pointed at me, but the computers ran fine.

On 12/9/09, Zane H. Healy <healyzh at aracnet.com> wrote: But we do use outside air to cool them. It's free except for the power to push it around. (Oh... and +35F is never seen at the Pole - the record is +7.5F, and I've personally been around for +7.0F). As for the extreme case, we've had computers malfunction when outside access doors were left open and -80F air came in directly, bypassing the blowers and the louvers. On a day-to-day basis, the room with the 14 racks that was AMANDA (it was shut down earlier this year after a 10+ year run) shed about 35-40kW of heat with indirect access to outside air with some measure of automatic and manual thermal controls (covering up open cable panels and stuffing blankets in hatches in addition to thermostatic controls on air blowers). If we let the room get over about +55F, the high-voltage supplies for the photomultipler tubes would go into thermal shutdown (ultra-dry air at 650millibars doesn't have much heat capacity). OTOH, and more to the point, if we let the room get much colder than about +35F (say +25F or colder), a specific rack of digital hardware that was adjacent to the floor vents feeding cold air to the high voltage supplies would malfunction until the temp came up to the high thirties to low forties. In another location entirely, central Ohio, I used to rent the basement of my mother's typing and typesetting shop. The building was a late 19th C/early 20th C brick "shotgun" commercial space with a former storm-cellar-type access to the basement. As such, cold air poured from the modern back door, down the basement stairs, and into the space I ran PDP-8s, PDP-11s and a VAX-11/730. One of my jobs at the time was hacking PDP-11 assembler on an 11/23. The basement would routinely get to +40F, and sometimes colder if the wind was from the right direction (the water pipes had electric wraps). I couldn't personally stand to work in that environment without a heater pointed at me, but the computers ran fine. The lone device that had problems was an LA-180 printer I used for listings. It worked down to about +45F, but colder than that, I speculate that the rail lubricant got too viscous, because it would blow carriage motor fuses until it warmed up. I quickly learned not to print on cold nights. I'd say that if you keep things at or above freezing, you are probably perfectly fine. Magnetic media is a lot more sensitive than ICs in terms of cold soaking. One thing to watch for is to not power up cold-soaked electronics. The current inrush is likely to blow ICs (the internal bonded wires between the die and the frame, mostly). I've thawed machines that were left in unheated buildings over the winter at McMurdo - ordinary temps around -45F or so. Specifically in that case (ultra cold, powered off), there are known and published "max rates of rise" of temps to minimize the risk of permanent damage from thermal expansion. A good rule of thumb is about 2-3 degrees per hour. What I did with the cold-soaked computers was to throw them into a lab freezer at -40F for a few hours, then into a lab environmental chamber at -30F that I would tweak up about 5 degrees every couple of hours. When the chamber was up to about +20F, I threw the equipment in a lab refrigerator. The thaw process took two workdays, but 100% of what I treated that way survived (no hard disk - these were floppy-booting diskless PCs that ran from a Novell server). If it gets really cold (+0F, say), I'd bring the disks in the house and leave the CPUs powered off until the garage temps are back around +32F. ICs can be stored down to -40 typically, but not operated at those temps (and especially not put through a power-on cycle at those temps). So that's my experience and observations of cold and computers. Take away from it what you will. -ethan