Do they have operations based on the address that the 8x300 is executing, like a typical bit slice? I used a WD1000 based controller on my Olivetti M20. It is actually a controller for a TRS-80 but it was a WD1000 in disguise. The M20 had what looked to be a wd1000 in the schematic I'd found. I was able to use a ST251 with it but needed to modify the step to be autovstep. The original Olivetti hard drive was a 10 ms and the ST251 doesn't go that fast but is actually faster with the auto stepping. It was a good thing the M20 software was very modular. Dwight ________________________________ From: cctalk <cctalk-bounces at classiccmp.org> on behalf of Eric Smith <spacewar at gmail.com> Sent: Saturday, November 19, 2016 4:06:31 PM To: General Discussion: On-Topic and Off-Topic Posts Subject: Reverse-engineering WD1000, WD1001 hard disk controllers I've been working a little bit off-and-on for years on reverse-engineering the WD1000 and WD1001 disk controllers (8X300/8X305-based), and their clones. I've only made any significant progress within the last few days, after hacking together my own disassesmbler which deals with the Fast I/O Select PROM. I do NOT recommend using this disassembler yet, for reasons that are explained in the README, but I've put it on github: https://github.com/brouhaha/s8x30x I've made some progress interpreting the firmware of an early WD1000, which only had 512 words of firmware, and didn't support run-time configurable sector size selection. So far I've figured out how they handle the host reading and writing the task file, dispatching the commands, and much of the sector ID search.

Hi Eric, Your Disassembler sounds very interesting. When you have a stable version, please let me know. I would be interested in seeing the disassembled source code for the WD1000 8-bit card I modified years ago. I had an MFM hard drive or two that I was trying to format, but the 4 sets of hard drive parameters offered by the WD1000 didn't match one of my hard drives so I replaced one of the sets of hard drive parameters by reading the eprom using my homebrew eprom burner setup I built for my Color Computer 1 F Board version way back when I was in my 20s. After getting the hex code into the Coco, I set out to figure out where that hard drive parameter table was located. I picked one of the set of hard drive parameters I didn't think I would ever need and replaced it with my own. I burnt the eprom, installed it into the WD1000 8-bit card and booted my MSDOS system and the WD1000 didn't respond. I turned everything off and uninstalled the eprom again. I looked through the entire eprom for some idea as to why the Hard drive controller was not working. I found one 8-bit byte at the very end of the eprom. I started wondering if that was a simple 8-bit summation of all the bytes in the eprom. I quickly wrote a basic program to add up all the bytes in the eprom since the hex code was loaded in my Coco to arrive at a new 8-bit sum. The result of that calculation was put into that last byte of the eprom file and burnt into the eprom. After reinstalling the WD1000 back into the computer, the WD1000 came right up and asked for my choice to pick for the hard drive parameters to use to format the hard drive with! It even included the set of hard drive parameters I had put into the eprom! I was very proud of what I had accomplished! All this was done at the hex level as I did not have a clue what the code was doing. I just needed different parameters for my MFM hard drive so I could format it to use on my system so I changed them. If I remember correctly, I was setting up a 20MB and 30MB hard drive for an old MSDOS machine I had put together. I think the 20MB was in the table, but the 30MB was not again if I am remembering this correctly. I probably still have that old WD controller somewhere if I can find it. I thought you guys might be interested in my experience modifying the WD1000 Eprom. I had a lot of fun figuring it all out. Now with Eric's disassembler, I'll be able to finally see the disassembled source code for it! It will be so cool to examine! Take care my friends. Kip Koon computerdoc at sc.rr.com http://www.cocopedia.com/wiki/index.php/Kip_Koon

I've put my work in progress on reverse-engineering the original WD1000 firmware on github: https://github.com/brouhaha/wd100x I use my own assembler syntax output by my previously mentioned s8x30x disassembler, so at the present there is no assembler for it. I expect to have an assembler in the not-too-distant future.