28 Sep
2012
28 Sep
'12
1:07 a.m.
Hi all --
Anyone have any experience getting Data I/O's Promlink software (I have
2.6, 3.4, and 6.1) to talk to a System 19 programmer? I've read through
the documentation on Bitsavers but it doesn't mention Promlink at all
(it's possible that it predates the software completely). Promlink says
it supports the System 19, and I've configured everything (baud rate,
etc) on both ends but I don't know the magic incantation to use on the
19's panel to make it talk.
Thanks,
Josh
28 Sep
28 Sep
8:15 a.m.
On 9/28/12 12:07 AM, "Josh Dersch" <derschjo at gmail.com> wrote:
Hi all --
Anyone have any experience getting Data I/O's Promlink software (I have
2.6, 3.4, and 6.1) to talk to a System 19 programmer? I've read through
the documentation on Bitsavers but it doesn't mention Promlink at all
(it's possible that it predates the software completely). Promlink says
it supports the System 19, and I've configured everything (baud rate,
etc) on both ends but I don't know the magic incantation to use on the
19's panel to make it talk.
Thanks,
Josh
I use Promlink 3.4 with my System 19. After I start the terminal program
running on the PC, I push SELECT, F, 1, START on the 19. The cursor (>)
will appear and you're ready to go.
1:18 p.m.
On 9/28/2012 5:15 AM, Richard Lynch wrote:
On 9/28/12 12:07 AM, "Josh Dersch"
<derschjo at gmail.com> wrote:
Thanks! That's exactly the missing information I needed and now
everything seems to be working happily. Now to dump some EPROMs...
Thanks again,
Josh
Hi all --
Anyone have any experience getting Data I/O's Promlink software (I have
2.6, 3.4, and 6.1) to talk to a System 19 programmer? I've read through
the documentation on Bitsavers but it doesn't mention Promlink at all
(it's possible that it predates the software completely). Promlink says
it supports the System 19, and I've configured everything (baud rate,
etc) on both ends but I don't know the magic incantation to use on the
19's panel to make it talk.
Thanks,
Josh
I use Promlink 3.4 with my System 19. After I start the terminal program
running on the PC, I push SELECT, F, 1, START on the 19. The cursor (>)
will appear and you're ready to go.
9:43 p.m.
On 9/28/12 12:57 PM, "Alexandre Souza - Listas" <pu1bzz.listas at
gmail.com>
wrote:
Huh?
I use Promlink
3.4 with my System 19. After I start the terminal program
running on the PC, I push SELECT, F, 1, START on the 19. The cursor (>)
will appear and you're ready to go.
Does LRLRUDUDABAB works on that too? :oO (konami code hehehe) :oD 
11:29 p.m.
I believe what we're experiencing here is what they call a generational gap. J/k My
blackberry also suggested perhaps I meant "gene rational". Boy do they know
their market.
Alexandre decided your boot method sounds a lot like an NES cheat code.
-----Original Message-----
From: Richard Lynch <richardlynch3 at verizon.net>
Sender: cctalk-bounces at classiccmp.orgDate: Fri, 28 Sep 2012 20:43:02
To: General Discussion: On-Topic and Off-Topic Posts<cctalk at classiccmp.org>
Reply-To: "General Discussion: On-Topic and Off-Topic Posts"
<cctalk at classiccmp.org>
Subject: Re: Getting Data I/O Promlink to talk to a System 19 programmer
On 9/28/12 12:57 PM, "Alexandre Souza - Listas" <pu1bzz.listas at
gmail.com>
wrote:
Huh?
I use Promlink
3.4 with my System 19. After I start the terminal program
running on the PC, I push SELECT, F, 1, START on the 19. The cursor (>)
will appear and you're ready to go.
Does LRLRUDUDABAB works on that too? :oO (konami code hehehe) :oD 
11:42 p.m.
Here is a photo of a Data I/O 29B, the replacement for the Model 19. Press
the blue "Select" key followed by the "F" and "1" key. Press
"Start" and the
programmer enables the serial port. All of the operations of the programmer
can be controlled by a computer or terminal. (The Model 29 may require two
presses of the Start Key.)
http://commons.wikimedia.org/wiki/File:Data_IO_29B_UniPak_2.jpg
The Computer Remote Control App Note can be found here:
http://bitsavers.trailing-edge.com/pdf/dataIO/
Michael Holley
-----Original Message-----
From: cctalk-bounces at classiccmp.org [mailto:cctalk-bounces at classiccmp.org]
On Behalf Of Richard Lynch
Sent: Friday, September 28, 2012 6:43 PM
To: General Discussion: On-Topic and Off-Topic Posts
Subject: Re: Getting Data I/O Promlink to talk to a System 19 programmer
On 9/28/12 12:57 PM, "Alexandre Souza - Listas" <pu1bzz.listas at
gmail.com>
wrote:
Huh?
I use Promlink
3.4 with my System 19. After I start the terminal
program running on the PC, I push SELECT, F, 1, START on the 19. The
cursor (>) will appear and you're ready to go.
Does LRLRUDUDABAB works on that too? :oO (konami code hehehe) :oD 
29 Sep
29 Sep
12:16 a.m.
On Fri, 28 Sep 2012, Richard Lynch wrote:
On 9/28/12 12:57 PM, "Alexandre Souza -
Listas" <pu1bzz.listas at gmail.com> wrote:
http://en.wikipedia.org/wiki/Konami_Code
...except that he got the code wrong ;P
On 9/28/2012 5:15 AM, Richard Lynch wrote:
Huh? I use Promlink 3.4 with my System 19. After I
start the terminal
program running on the PC, I push SELECT, F, 1, START on the 19. The
cursor (>) will appear and you're ready to go.
Does LRLRUDUDABAB works on that too? :oO (konami code hehehe) :oD
4347
days inactive
4348
days old
7 comments
6 participants
participants (6)
-
barythrin＠gmail.com -
derschjo＠gmail.com -
pu1bzz.listas＠gmail.com -
richardlynch3＠verizon.net -
swtpc6800＠comcast.net -
tothwolf＠concentric.net