Hi Guy! Thanks for the post and interesting. No it's not quite the exact power supply but close. However.... Are you *sure* those cards are in the right slots? Reason I am asking: When I look at the HP docs they label the Pre-regulator board as A3A1. A3A1 also has the red LED. The inverter board (the one with the transistors and transformers) is A3A2. Likewise the battery charge boards are A3A3, A3A4, and the control board at the end is A3A5. The slots are labeled 1-5 with 1 being closest to the power cord and 5 being on the output end. A3A5 will only fit in slot 5, and A3A4 has the 12 volt trim pot that is accessible outside the supply by a cut-out so it has to be in slot 4. Slot 3 is not used on my unit because I don't have the battery backup circuits. However in your picture slot 2 has the LED preregulator board and slot 1 has the one with the transistors and transformers (inverter). So either your picture has the parts backwards or someone at HP should go to hell for exceptionally bad numbering. Does your supply work? C On 9/10/2021 12:43 PM, Guy Dunphy wrote:

At 11:41 PM 10/09/2021 -0400, you wrote: Hmm... I was starting on that system back in Nov 2013. I'm pretty careful about taking photos of stuff as I take it apart. There's 20 minutes time between the photo with the PS cover on, and the next with it off, showing the boards in place. My memory of that long ago is faded, but I think that 20 minutes was mostly spent looking at the mains voltage selector jumpers, and finding that whoever had originally converted it to 240V had very nicely saved the now unused jumpers in a small plastic bag shoved down between the small transformer and the big blue electro. This was the first time I'd ever opened the machine, let alone extracted and opened the PS. So I am _quite_sure_ the boards are as they were when I got the machine. Its history - I'd rescued it from a junkyard and imminent destruction. It was complete with many I/O cards, two HP tape drives, original HP green racks, but no hard disks. It had been part of a larger system, with no information about its operational condition. Anyway I'd just assumed it was 'previously working, left idle for years.' Then I'd stored it for some more years, untried. Too busy with work, family, etc. Finally got to it. Story: http://everist.org/NobLog/20131112_HP_1000_minicomputer_teardown.htm Where I got to, was quickly attempting to run the power supply by itself, to verify voltages before reconnecting to the system. It didn't do anything sensible, and I'd assumed this was something to do with the PWR CONT IN and BATT INPUT connectors not seeing expected states. So I needed a manual. Asking around, I got in contact with Jon Johnston of the HP Museum in Victoria Australia. He was away mountain climbing. Later I tried again, in the meantime he'd returned then gone climbing in Himalayas again. This time he died there. A good friend of mine had also died climbing in the Himalayas, so this project acquired an aversion factor. Lacking a schematic, I'd have to disassemble the supply completely and reverse engineer the circuits. Not too hard but time consuming. And I was having other life problems. So the machine got boxed up and shelved - JUST before I'd have started actually looking into how the PS was supposed to work. When I would have discovered the board swap. Now, looking at the photos, you are right! Those two boards are definitely swapped. I just dug out the machine now and am looking at it. Thinking back to 2013 I recall wondering about the way the TO3 transistor leg socket-pins on the board next to the big blue cap, were pressing into the insulating jacket of the cap. I recall thinking that didn't seem like a good design. I'd also spotted the two cards _could_ be interchanged, and written "Pre-Reg" on the card that is actually the inverter board. Because it was in the pre-reg slot. Monkey-see... Also noted that the lower TO3 heatsink fins were pressing on the wires from P11. So I bent the fins up a little bit. No reason to think these problems could be due to swapped boards! The slots have "PRE-REG BD" and "INVERTER BD" written in the component silkscreen, right next to them, very obviously. Which makes me feel pretty stupid for not realising the swap, given how clearly the boards are a small regulator vs power driver. Also hadn't thought to check the board part numbers against those listed on the power supply cover. (IMG_6081.jpg) Which would have immediately revealed they were swapped. How did that happen? Someone in the last days of the machine's operation, trying to fix a fault, giving up, shoving stuff back together carelessly? Or a deliberate 'make it not work for the auction' thing? (But there was never an auction.) Or did I have a brain fart, take the boards out in that 20 minute gap, and put them back in wrong - violating my own rule about 'photos first'? (I really don't think so.) Anyway... So now I know I powered it up with those boards in swapped slots. Means I _really_ need a schematic. Maaaybe nothing bad happened. But I'd rather check. All the online PS manuals I've found online are for earlier models. My system is a 2113E. Power supply 5061-6615 SN: 2340 The layout of my inverter and pre-reg boards are different than in the earlier manuals. Pic: http://everist.org/pics/hp1000_ps/20210911_9766.jpg I had also found this manual 92851-90001_Sections-IXB-X_Mar-1981.pdf which is for an earlier PS than mine. I think it came from bitsavers. I've copied it to the same folder as the pics above. Does it match your PS? I _still_ don't have time to allocate to tracing out the power supply schematic. Guy Further review: Looking at photo IMG_6081.jpg it shows the layouts of the boards. Specifically A1 is the pre-regulator board pn 5061-3457 which is the one with the caps and A2 is Inverter board PN 5061-3454. I think if your PS doesn't work one problem is these boards are backwards. Don't know if that will blow up your supply but interesting to note... Hm.... From what I can see it looks like the 120 goes into a transformer on the bulkhead and is stepped down to 24 volts DC which then feeds "stuff". I'll start there and see if I get 24dc at the first stage, which should then be filtered by the caps and sent on to the various regulators. C

Ok, thanks! I just tried mine again, it's a dud so I am going to have to figure it out. First step was to see if the rectifier had any voltage so I disconnected the + side and checked it with a voltmeter. With 120v plugged in I saw 200v DC which is probably not too far off. That seems to go to the inverter card, which I don't know what it's doing with that. Is there a block schematic of what does what on this PS?

Ah ok. So that first transistor on Q6 serves as a chopper to double the DC voltage up to 360v when using 120. When you reconfigure the jumpers for 240 you basically bypass that thing. I have 240 in my shed so I'll start by seeing if there is 360v on the input rail. If not then I'll re-jumper to 240 and see if it appears then. Then trace everything forward from there.... C On 9/13/2021 1:22 AM, J. David Bryan via cctech wrote: