25 Nov
2018
25 Nov
'18
8:56 a.m.
Folks,
While sorting through my pile of 3270 terminals I came across a little
plastic box with 2 x 9-pin rs232, 1x25pin printer port and one VGA port. On
taking the lid off it seems it's a terminal for NYCE made by TCL but I can
find no info on the net.
I put a few pics of it here:-
https://1drv.ms/f/s!Ag4BJfE5B3onkY8FlfveCwr73J5HIw
I can't seem to get into ant set-up menus, and I am sure it used to show
these, Does any one have any documents on these?
Searching on google is hampered by the fact there is a TCL language.
Dave Wade
G4UGM & EA7KAE
9:24 a.m.
you accidentally included a pic of the memorex terminal as picture 1 so there isn't a
picture of the
back of the board. I'm assuming there is an AT keyboard connector on the TCL
On 11/25/18 9:22 AM, Al Kossow via cctalk wrote:
On 11/25/18 8:56 AM, Dave Wade via cctalk wrote:
I can't seem to get into ant set-up menus,
and I am sure it used to show
these, Does any one have any documents on these?
try holding down the space bar on powerup
dumps of the firmware would be nice
9:41 a.m.
Don't know the exact product, but TCL INc. was in Fremont, CA and was a
maker of various bits of LAN gear.
--Chuck
9:55 a.m.
'TCL' are the initials of the person who created the first Ethernet transceiver
(Tat Lam).
https://books.google.com/books?id=ooBqdIXIqbwC&pg=PA73&lpg=PA73
He also sold the first 10mbit transceiver and repeater.
On 11/25/18 9:41 AM, Chuck Guzis via cctalk wrote:
Don't know the exact product, but TCL INc. was in
Fremont, CA and was a
maker of various bits of LAN gear.
--Chuck
10:24 a.m.
On 11/25/18 9:55 AM, Al Kossow via cctalk wrote:
'TCL' are the initials of the person who
created the first Ethernet transceiver (Tat Lam).
https://books.google.com/books?id=ooBqdIXIqbwC&pg=PA73&lpg=PA73
I note that the same section mentions Jim Theornton. I recall on a trip
to CDC ARHOPS in Arden Hills, seeing a backhoe trenching around the
employee parking lot. The path didn't make much sense, so I asked a
co-worker about it. "Oh, that's Jim Thornton laying his coax loop."...
--Chuck
11:02 a.m.
Oops.
Yes the back has VGA, 2 x 9-pin din for serial, 1x25 pin, DIN Keyboard and Din light pen
IEC mains in, mains out for display.
I will pop a picture up later...
... and I will try the space bar on switch on
Dave
-----Original Message-----
From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Al Kossow via
cctalk
Sent: 25 November 2018 17:25
To: cctalk at classiccmp.org
Subject: Re: TCL Terminal
you accidentally included a pic of the memorex terminal as picture 1 so there
isn't a picture of the back of the board. I'm assuming there is an AT keyboard
connector on the TCL
On 11/25/18 9:22 AM, Al Kossow via cctalk wrote:
>
>
> On 11/25/18 8:56 AM, Dave Wade via cctalk wrote:
>
>> I can't seem to get into ant set-up menus, and I am sure it used to
>> show these, Does any one have any documents on these?
>
> try holding down the space bar on powerup
>
> dumps of the firmware would be nice
>
>
2:53 p.m.
-----Original Message-----
From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Al Kossow via
cctalk
Sent: 25 November 2018 17:22
To: cctalk at classiccmp.org
Subject: Re: TCL Terminal
On 11/25/18 8:56 AM, Dave Wade via cctalk wrote:
No
I can't seem to get into ant set-up menus,
and I am sure it used to
show these, Does any one have any documents on these?
try holding down the space bar on powerup
dumps of the firmware would be nice
I think that?s the only way I will find out if there is a setup menu. I am beginning to
think it might be a dedicated function terminal with no config options.
It does work as a terminal on but its not ANSI/VT. When I run EDIT on the VAX it goes into
some graphics mode.
I have put it on to my ToDo list but don't hold your breath.
Dave
G4UGM
2219
days inactive
2219
days old
8 comments
3 participants
participants (3)
-
aek＠bitsavers.org -
cclist＠sydex.com -
dave.g4ugm＠gmail.com