20 Jun
2003
20 Jun
'03
4:29 a.m.
I have a 'new' microVAX 4000-200 here that has a few small oddities
with it, and I could use some advice. Number one is that it will not boot.
I tried 'b dia0' and 'b/r5:e0000001 dia0' and both times it's nothing
until
timeout. Number two is that 'show dssi' and 'sho dev' show no disks, nor
the TF85. After some initial confusion where one or more disks were
tried uncabled before powerup, the DSSI terminator was discovered
missing, so I used one from another machine.
My questions are, are there other tests for a disk besides booting it,
and, what could be wrong with the DSSI bus?
I tried other DSSI ID's on the disks but no real change.
Do the ID's have to start with 0?
A tidbit with the terminator off was that the countdown tests went from
95.. to 60.. and then autobooted immediately back to 95 without continuing
down. I could have sworn at the time that 'sho dssi' worked then.
Probably unreleted but FYI.
TIA
John A.
20 Jun
20 Jun
8:04 a.m.
Once you are able to see the disks you should be able to SET HOST/DUP to
them from the console but you're obviously not there yet.
Have you tried hooking the devices one at a time and doing a SHOW DEVICE?
I take it the red 'fault' light is not coming on on the drives?
Does your host even show up in the SHOW DEVICE?
DSSI Node 6 (*)
- or -
DSSI Node 7 (*)
Perhaps the full output of SHOW DEVICE might be helpful.
On Fri, 20 Jun 2003, John Allain wrote:
I have a 'new' microVAX 4000-200 here that has
a few small oddities
with it, and I could use some advice. Number one is that it will not boot.
I tried 'b dia0' and 'b/r5:e0000001 dia0' and both times it's nothing
until
timeout. Number two is that 'show dssi' and 'sho dev' show no disks,
nor
the TF85. After some initial confusion where one or more disks were
tried uncabled before powerup, the DSSI terminator was discovered
missing, so I used one from another machine.
My questions are, are there other tests for a disk besides booting it,
and, what could be wrong with the DSSI bus?
I tried other DSSI ID's on the disks but no real change.
Do the ID's have to start with 0?
A tidbit with the terminator off was that the countdown tests went from
95.. to 60.. and then autobooted immediately back to 95 without continuing
down. I could have sworn at the time that 'sho dssi' worked then.
Probably unreleted but FYI.
TIA
John A.
--
2:50 p.m.
I take it the red 'fault' light is not coming
on on the drives?
Just once, but it cleared.
Here's the boot seq. I was talking about:
"KA660-A V4.9, VMB 2.12
Performing normal system tests.
95..94..93..92..91..90..89..88..87..86..85..84..83..82..81..80..
79..78..77..76..75..74..73..72..71..70..69..68..67..66..65..64..
63..62..61..60.."
(stops and loops back to the beginning for ~3 minutes... then:)
"KA660-A V4.9, VMB 2.12
Performing normal system tests.
95..94..93..92..91..90..89..88..87..86..85..84..83..82..81..80..
79..78..77..76..75..74..73..72..71..70..69..68..67..66..65..64..
63..62..61..60..59..58..57..56..55..54..53..52..51..50..49..48..
47..46..45..44..43..42..41..40..39..38..37..36..35..34..33..32..
31..30..29..28..27..26..25..24..23..22..21..20..19..18..17..16..
15..14..13..12..11..10..09..08..07..06..05..04..03..
Tests completed."
(came up to temperature...perhaps?)
Wonder what test 59 is and what a failure there signified?
Does your host even show up in the SHOW DEVICE?
DSSI Node 7 (*)
Yes, like that.
Perhaps the full output of SHOW DEVICE might be
helpful.
Here:
">>>sho dev
DSSI Bus 0 Node 7 (*)
UQSSP Tape Controller 0 (774500)
-?
Ethernet Adapter
-EZA0 (08-mac..mac-F7)"
The "-?" looks wierd.
sho dssi, again, showed no tape. nothin' but controller.
thx for responding.
John A.
21 Jun
21 Jun
2:50 p.m.
That -? does look odd. Could the UQSSP have been added in later?
You have nothing hooked to it if your only tape is a TF series drive,
true?
I don't know what to make of the self tests. Perhaps someone configured a
script of tests. There is supposed to be a way to do that.
What does T 9E show? On other/older machine this lists the selftests.
Sorry for top posting
Paul
On Fri, 20 Jun 2003, John Allain wrote:
--
I take it the
red 'fault' light is not coming on on the drives?
Just once, but it cleared.
Here's the boot seq. I was talking about:
Wonder what test 59 is and what a failure there signified?
Does your host even show up in the SHOW DEVICE?
DSSI Node 7 (*)
Yes, like that.
Perhaps the full output of SHOW DEVICE might be
helpful.
Here:
">>>sho dev
DSSI Bus 0 Node 7 (*)
UQSSP Tape Controller 0 (774500)
-?
Ethernet Adapter
-EZA0 (08-mac..mac-F7)"
The "-?" looks wierd.
sho dssi, again, showed no tape. nothin' but controller.
thx for responding.
John A.
22 Jun
22 Jun
4:05 a.m.
That -? does look odd. Could the UQSSP have been
added in later?
You have nothing hooked to it if your only tape is a TF series drive,
true?
There's an odd SCSI card (CMD 220) in it, that could be it.
A next set of tests would be to remove excess cards, and try
again.
What does T 9E show? On other/older machine this
lists the selftests.
Here's the t 9e.
Noticing now that one set of tests is in dec. (boot) and one's in hex. (this
one), then 59=3B, and we get 'test not shown'.
If somebodies' got a book to crack on this one that might be needed.
John A.
Test
# Address Name Parameters
___________________________________________________________________________
20052800 SCB
2005377C De_executive
30 2005D564 MS650_Init_Bitmap *** mark_Hard_SBEs ******
31 2005D324 MS650_Setup_CSRs **********
32 2005CE6C CMCTL regs MEMCSR0_addr *********
33 2005CE28 CMCTL_powerup *
34 20054ECC SSC_ROM *
3F 2005F3A8 MS650_FDM_Addr_shorts *** cont_on_err ******
40 2005FB90 MS650_count_pages First_board Last_bd Soft_errs_allowed
*******
41 20062CCC Board_Reset *
42 20054F8C Chk_for_Interrupts *****
43 2005B268 SOC_DI_Cache_w_mem cache_config start_add end_add add_incr
******
44 2005AA9C SOC_D_Cache_w_Mem cache_config start_add end_add add_incr
******
45 2005A6FC SOC_Cache_mem_CQBIC cache_config start_add end_add add_incr
******
46 2005B784 SOC_Cache1_diag_mode cache_config addr_incr ********
47 2005F920 MS650_Refresh start_a end incr cont_on_err time_seconds
*****
48 2005EFDC MS650_Addr_shorts start_add end_add * cont_on_err pat2 pat3
****
49 2005EA18 MS650_FDM *** cont_on_err ******
4A 2005E770 MS650_ECC_SBEs start_add end_add add_incr cont_on_err
******
4B 2005E530 MS650_Byte_Errors start_add end_add add_incr cont_on_err
******
4C 2005DFD4 MS650_ECC_Logic start_add end_add add_incr cont_on_err
******
4D 2005DE44 MS650_Address start_add end_add add_incr cont_on_err
******
4E 2005DC50 MS650_Byte start_add end_add add_incr cont_on_err
******
4F 2005D9A4 MS650_Data start_add end_add add_incr cont_on_err
******
51 20062D9B FPA *******
52 20055538 SSC_Prog_timers which_timer wait_time_us ***
53 20055808 SSC_TOY_Clock repeat_test_250ms_ea Tolerance ***
54 20055062 Virtual_Mode *********
55 200559BE Interval_Timer *
58 20061924 SHAC_RESET dssi_bus port_number time_secs
59 20060A78 SGEC_LPBCK_ASSIST time_secs **
5A 2005A600 SOC_CMCTL dont_report_memory_bad repeat_count *
5C 20060FE0 SHAC shac_number *******
5F 2005FD64 SGEC loopback_type no_ram_tests ******
60 2005A22D SSC_Console_SLU start_BAUD end_BAUD ******
62 20055DFC console_QDSS mark_not_present selftest_r0 selftest_r1
*****
63 20055F78 QDSS_any input_csr selftest_r0 selftest_r1 ******
80 20059C0D CQBIC_memory_LMGH **********
81 20055A60 Qbus_MSCP IP_csr ******
82 20055C25 Qbus_DELQA device_num_addr ****
83 20056E82 QZA_Intlpbck1 controller_number ********
84 2005853C QZA_Intlpbck2 controller_number *********
85 200560D4 QZA_memory incr test_pattern controller_number *******
86 20056590 QZA_DMA Controller_number main_mem_buf ********
87 20059780 QZA_EXTLPBCK controller_number ****
90 200554B6 CQBIC_registers *
91 2005544C CQBIC_powerup **
99 20062FA9 Flush_Ena_Caches dis_flush_cache *********
9A 20061EB0 INTERACTION pass_count disable_device ****
9B 20062B8C Init_memory_4MB *
9C 2005C02A List_CPU_registers *
9D 2005CD06 Utility Expnd_err_msg get_mode init_LEDs clr_ps_cnt
9E 20055A32 List_diagnostics *
9F 200630E6 Create_A0_Script **********
C1 20054B78 SSC_RAM_Data *
C2 20054D4E SSC_RAM_Data_Addr *
C5 20059A51 SSC_registers *
C6 20054ABC SSC_powerup *********
C7 20059B58 SSC_CBTCR_timeout ***
Scripts
# Description
A0 User defined scripts
A1 Powerup tests, Functional Verify, continue on error, numeric countdown
A3 Functional Verify, stop on error, test # announcements
A4 Loop on A3 Functional Verify
A5 Address shorts test, run fastest way possible
A6 Memory tests, mark only multiple bit errors
A7 Memory tests
A8 Memory acceptance tests, mark single and multi-bit errors, call A7
A9 Memory tests, stop on error
B5 Cache tests, report errors
2:30 p.m.
The machine seems usable now.
It's flaky in a way I don't understand.
Both the PSU's have green lights on them but when
it comes up it autoreboots at test 60.. continuously for
a reason I have to determine someday.
Until then it seems to be OK if I halt the boot, wait about
four minutes and then restart. It goes all the way to boot
3.. and then takes the 'b dia0', and 'sho dssi'. Whatever.
Anyone recognizing the symptoms can add a message.
Till then.
John A.
23 Jun
23 Jun
6:15 a.m.
Noticing now that one set of tests is in dec. (boot)
and
one's in hex. (this one), then 59=3B, and we get 'test not
shown'. If somebodies' got a book to crack on this one that
might be needed.
You can search at http://vt100.net/manx if you want a goodly
selection of relevant manuals. "KA660" and "VAX 4000 200"
will pull up the relevant manuals.
Happy reading.
Antonio
--
---------------
Antonio Carlini arcarlini(a)iee.org
7853
days inactive
7856
days old
6 comments
3 participants
participants (3)
-
allain＠panix.com -
arcarlini＠iee.org -
thompson＠new.rr.com