The real trick is figureing out the capacity of the chips from the markings on them. Google searches sometimes help, but often (almost always) just lead you to chip distributers spamming the search engine space with part numbers to lead part searches to their sites. They often don't even have the chip in question, and rarely have any useful information available on their website.

I beliee that most PCs could make use of the added parity bit, while Macs didn't care if it was present.

what. Not all that painless, but the only way I know that works... Take a SIMM. Count the number of chips. Find the model markings on one of the chips. There are usually two or three lines of writing on a chip. One of these will be a date or batch code and is irrelevant. The line you want will start with a one, two or three (usually two) character manufacturer code (e.g., K or KM for Samsung, TC for Toshiba, M(numeral)M for Mitsubishi, HM or HN for Hitachi, etc.), followed by some longish, about four to eight, alphanumeric code which is mostly numerals, then a dash or space and a speed number in nanoseconds, which may or may not have the trailing zero truncated. For example: HM5116400BS-8, MSM511000C-7, KM44C16100B-5, TC514400AJ-6. Then go to a datasheet archive such as <http://www.datasheetarchive.com/> and enter the part number in the search field. It often helps to truncate the trailing characters back to the first number in the body. E.g. HM5116400, MSM511000, KM44C16100, etc. The datasheet will tell you the capacity and organization of the chip. For example, a 1 MB 30 pin SIMM with eight chips on it will be composed of 1M X 1 chips. These have one million addresses with 1 bit at each address. Eight of them working in parallel provide 1 million addresses with eight bits at each address or 1 megabyte. Multiply the total capacity of the chip by the number of chips on the SIMM. Remember that you're working with bits here, not bytes. Divide by 8 and you've got the capacity in megabytes--except... Some SIMMs are parity SIMM and they are based on 9 bits of data rather than 8 bits of data, so you'll need to divide that capacity by 9, not by eight for a parity SIMM. A 30 pin parity SIMM will have nine or three chips instead of eight or two, so they're fairly easy to identify. However, a three chip 30 pin SIMM will have two chips with a certain capacity and a third chip with 1/4 the capacity or either of the other two. In this case, calculate the total capacity of the two larger chips and divide by eight. Or find the capacity in bits of one big chip and divide by four. In most cases, if the SIMM has eight or nine chips, then the capacity in bytes is equal to the number of addresses any of the chips supports (see the datasheet). If the SIMM has three chips, then the capacity in bytes is still equal to the number of address which any of the three chips supports. For example, you find a three chip SIMM with two 4M X 4 chips and one 4M X 1 chip on board. The capacity of this SIMM is 4MB or 4 Megabytes. You find a SIMM with eight or nine 4M X 1 chips on board, its capacity is also 4MB. The real trick is figureing out the capacity of the chips from the markings on them. Google searches sometimes help, but often (almost always) just lead you to chip distributers spamming the search engine space with part numbers to lead part searches to their sites. They often don't even have the chip in question, and rarely have any useful information available on their website. SIMMs that can steer you wrong are composite SIMMs where groups of smaller capacity chips are used to build a higher capacity SIMM. For example, building a 16 MB 30 pin SIMM out of eight 4M X 4 chips. These are rare and should be easily identified because there should be a non-memory chip on board to handle the address translations. Jeff Walther