14 Dec
2017
14 Dec
'17
4:47 a.m.
From: John Welch
CLR
765000
LAD
EXAM
'Bus Err' light comes on.
Oooh, that's very interesting, and illuminative. The ROM isn't working (so
there's no way for the software console to work - its code is in that ROM).
So look at Section 1.5 of the Technical Manual
http://bitsavers.org/pdf/dec/unibus/M9312_TechRef.pdf
and make sure all the jumpers on the M9312 are as required. In particular,
jumper W-8 should be _out_.
If it's not, that would explain why the ROM at 765000 isn't resonding. If
it's
in, that M9312 board probably has a problem.
Also, while we're at it, it's probably worth making sure the CPU will
run. Do this:
CLR
LAD
777 (This is a 'branch .' instruction)
DEP
EXAM (Should display '777')
CLR (I think you can dispense with these
LAD two, but just to be safe...)
CTRL-START
'Run' light should come on
CTRL-HALT
'Run' light should go out, should display '0' (or maybe '2', I
forget)
Do you know which color wire (red, clear, black) goes
to which festoon
connector (TP1, TP2, TP3, TP4)?
I would leave them all disconnected for the moment; you don't need them. One
is the 'boot' switch on the console, and its ground. The other is the 'boot
on
power on enable' (a duplicate of S1-2), and its ground. Since we're trying to
manually start the ROM console from the front console, they aren't needed for
that.
I don't recall offhand which one connects to which - I will have to check.
Don't want to blow anything up.
Not sure it will harm anything if you connect things wrongly, but that's
not tested.
Noel
14 Dec
14 Dec
6:43 a.m.
On 12/14/2017 6:47 AM, Noel Chiappa wrote:
Will do.? I have 4 M9312
cards.? One I know I pulled from an 11/04, the
others from 11/04 or 11/34 (or 11/34a)
[...]
--
Sincerely,
John Welch
281-353-4706 Home
713-725-7017 Cell
:qw
From: John
Welch
CLR
765000
LAD
EXAM
'Bus Err' light comes on.
Oooh, that's very interesting, and illuminative. The ROM isn't working (so
there's no way for the software console to work - its code is in that ROM).
So look at Section 1.5 of the Technical Manual
http://bitsavers.org/pdf/dec/unibus/M9312_TechRef.pdf Also, while we're at it, it's probably worth
making sure the CPU will
run. Do this:
CLR
LAD
777 (This is a 'branch .' instruction)
DEP
EXAM (Should display '777')
CLR (I think you can dispense with these
LAD two, but just to be safe...)
CTRL-START
'Run' light should come on
CTRL-HALT
'Run' light should go out, should display '0' (or maybe '2', I
forget)
It read 000000
Do you know which color wire (red, clear, black)
goes to which festoon
connector (TP1, TP2, TP3, TP4)?
I would leave them all disconnected for the moment; you don't need them. One
is the 'boot' switch on the console, and its ground. The other is the 'boot
on
power on enable' (a duplicate of S1-2), and its ground. Since we're trying to
manually start the ROM console from the front console, they aren't needed for
that.
I don't recall offhand which one connects to which - I will have to check.
Don't want to blow anything up.
Not sure it will harm anything if you connect things wrongly, but that's
not tested.
Noel
7:28 a.m.
The "@" is on the screen in HyperTerminal.
I have 4 M9312 cards.? Three have W8 jumped, one did not.? I put in the
M9312 w/o W8 and when I power on I see the "@" on the screen.
Now for the next snag. The bitsavers document suggests L<SPC>777<CR> ;
E<SPC> which should echo some digits.? However nothing pops up.
So I am wondering if I have the handshaking set right?
On 12/14/2017 6:47 AM, Noel Chiappa wrote:
--
Sincerely,
John Welch
281-353-4706 Home
713-725-7017 Cell
:qw
From: John
Welch
CLR
765000
LAD
EXAM
'Bus Err' light comes on.
Oooh, that's very interesting, and illuminative. The ROM isn't working (so
there's no way for the software console to work - its code is in that ROM).
So look at Section 1.5 of the Technical Manual
http://bitsavers.org/pdf/dec/unibus/M9312_TechRef.pdf
and make sure all the jumpers on the M9312 are as required. In particular,
jumper W-8 should be _out_.
If it's not, that would explain why the ROM at 765000 isn't resonding. If
it's
in, that M9312 board probably has a problem.
Also, while we're at it, it's probably worth making sure the CPU will
run. Do this:
CLR
LAD
777 (This is a 'branch .' instruction)
DEP
EXAM (Should display '777')
CLR (I think you can dispense with these
LAD two, but just to be safe...)
CTRL-START
'Run' light should come on
CTRL-HALT
'Run' light should go out, should display '0' (or maybe '2', I
forget)
Do you know which color wire (red, clear, black)
goes to which festoon
connector (TP1, TP2, TP3, TP4)?
I would leave them all disconnected for the moment; you don't need them. One
is the 'boot' switch on the console, and its ground. The other is the 'boot
on
power on enable' (a duplicate of S1-2), and its ground. Since we're trying to
manually start the ROM console from the front console, they aren't needed for
that.
I don't recall offhand which one connects to which - I will have to check.
Don't want to blow anything up.
Not sure it will harm anything if you connect things wrongly, but that's
not tested.
Noel 
8:16 a.m.
For a quick read of the most important information of the M9312, see
www.pdp-11.nl/pdp11-34a/cpu/options/bootstrap-info.htm<http://www.pdp-11…
It contains some interesting side notes from Don (at the end)
Van: Noel Chiappa via cctalk<mailto:cctalk at classiccmp.org>
Verzonden: donderdag 14 december 2017 13:47
Aan: cctalk at classiccmp.org<mailto:cctalk at classiccmp.org>
CC: jnc at mercury.lcs.mit.edu<mailto:jnc at mercury.lcs.mit.edu>
Onderwerp: Re: 11/04 Project
From: John Welch
CLR
765000
LAD
EXAM
'Bus Err' light comes on.
Oooh, that's very interesting, and illuminative. The ROM isn't working (so
there's no way for the software console to work - its code is in that ROM).
So look at Section 1.5 of the Technical Manual
http://bitsavers.org/pdf/dec/unibus/M9312_TechRef.pdf
and make sure all the jumpers on the M9312 are as required. In particular,
jumper W-8 should be _out_.
If it's not, that would explain why the ROM at 765000 isn't resonding. If
it's
in, that M9312 board probably has a problem.
Also, while we're at it, it's probably worth making sure the CPU will
run. Do this:
CLR
LAD
777 (This is a 'branch .' instruction)
DEP
EXAM (Should display '777')
CLR (I think you can dispense with these
LAD two, but just to be safe...)
CTRL-START
'Run' light should come on
CTRL-HALT
'Run' light should go out, should display '0' (or maybe '2', I
forget)
Do you know which color wire (red, clear, black) goes
to which festoon
connector (TP1, TP2, TP3, TP4)?
I would leave them all disconnected for the moment; you don't need them. One
is the 'boot' switch on the console, and its ground. The other is the 'boot
on
power on enable' (a duplicate of S1-2), and its ground. Since we're trying to
manually start the ROM console from the front console, they aren't needed for
that.
I don't recall offhand which one connects to which - I will have to check.
Don't want to blow anything up.
Not sure it will harm anything if you connect things wrongly, but that's
not tested.
Noel
2565
days inactive
2565
days old
3 comments
3 participants
participants (3)
-
henk.gooijen＠hotmail.com -
jcwelch＠hal-pc.org -
jnc＠mercury.lcs.mit.edu