22 Dec
2020
22 Dec
'20
10:17 p.m.
The ready lamp flashes not when the servo burst is
>visible, but when the
heads are just before it.
Why? Well, I probably set the gain too high on the
read/write module.
Hello,
I'm sure you read the manual, however I add some explanation to be sure.
The best head position is not where a servo track is at maximum amplitude
(head is exactly centered to a servo track), but where you read two servo
tracks with the same amplitude (so head is exactly between two servo
tracks, in middle position).
Comparative measurement of two servo tracks allow the servo control to
understand the position of the head in respect to data track.
If the best position for data track is not where servo have same amplitude
probably the head is misaligned or the spring support of the head bent /
deformed.
To analyze head circuits you need a good oscilloscope, you should be able
to see burst of servo tracks and data tracks too, with two channels you can
understand if analog to digital threshold / pulses signal conversions do
work as expected.
Time ago I fixed an RL02 having a malfunctioning head amplifier circuit.
The gain was too low. When I increased it rotating variable resistor, the
circuit begun to ring (barely auto-oscillate), so was nearly unstable. Data
and servo signals were corrupted, but this was visible only zooming on
oscilloscope after careful trigger alignment.
I don't remember exactly what I did, but some capacitors needed
replacement, then I tuned head gain while loading a platter to the best
position for operation, maybe slightly lower than manual recommendations.
Then it worked perfectly.
Andrea
22 Dec
22 Dec
10:37 p.m.
On 22 December 2020 at 22:17 GMT, shadoooo via cctalk wrote:
Hi Andrea,
Thanks for this. My understanding is that the S1 and S2 servo bursts are
passed through a comparator and then integrated. When the head is
directly over the target track, S1 (becomes E1 after integration) is a
perfect saw tooth, while E2 'saw tooths' away from 0V.
After performing the amplitude adjustment, the potentiometer was very
close to max, and I was getting around 650mV from the cartridge, but the
noise floor was quite high. The manual also says that the outer guard
track should not have an amplitude greater than 2.5V. Presumably the
amplitude on the platter is higher the further out the track is, perhaps
due to the amount of space available given 40 sectors per track.
With this amplitude set as mentioned, loading the cartridge results in
this head unpredictable oscillating behaviour, but as I mentioned, the
ready light only comes on briefly, and only when the heads are before
the outer guard. Basically, as far as they could be off the platter
before being lifted by the ramp.
Reducing the amplitude slightly prevents this oscillating behaviour, but
the ready lamp does not come on at all. Increasing it to the very max
causes very extreme oscillation, sometimes aggressively unloading the
heads.
I happen to have three of the read/write modules, and they all exhibit
this behaviour. Not to say that caps don't need to be changed, but it
seems unlikely that all of them would need this.
I have a fairly decent scope and have been able to do some very nice
captures of the servo bursts. They are not perfectly sinusoidal but I
think close enough given the age of the heads.
I'll go through the caps at some point anyway to double check. Looking
at the schematic I'm guessing they are either ceramic or tants.
thanks again,
Aaron
This message and any attachment are intended solely for the addressee
and may contain confidential information. If you have received this
message in error, please contact the sender and delete the email and
attachment.
Any views or opinions expressed by the author of this email do not
necessarily reflect the views of the University of Nottingham. Email
communications with the University of Nottingham may be monitored
where permitted by law.
The ready lamp
flashes not when the servo burst is >visible, but when the
heads are just before
it.
Why? Well, I probably set the gain too high on
the read/write module.
Hello,
I'm sure you read the manual, however I add some explanation to be sure.
The best head position is not where a servo track is at maximum amplitude
(head is exactly centered to a servo track), but where you read two servo
tracks with the same amplitude (so head is exactly between two servo
tracks, in middle position).
Comparative measurement of two servo tracks allow the servo control to
understand the position of the head in respect to data track.
If the best position for data track is not where servo have same amplitude
probably the head is misaligned or the spring support of the head bent /
deformed.
To analyze head circuits you need a good oscilloscope, you should be able
to see burst of servo tracks and data tracks too, with two channels you can
understand if analog to digital threshold / pulses signal conversions do
work as expected.
Time ago I fixed an RL02 having a malfunctioning head amplifier circuit.
The gain was too low. When I increased it rotating variable resistor, the
circuit begun to ring (barely auto-oscillate), so was nearly unstable. Data
and servo signals were corrupted, but this was visible only zooming on
oscilloscope after careful trigger alignment.
I don't remember exactly what I did, but some capacitors needed
replacement, then I tuned head gain while loading a platter to the best
position for operation, maybe slightly lower than manual recommendations.
Then it worked perfectly.
Andrea
1469
days inactive
1469
days old
1 comments
2 participants
participants (2)
-
Aaron.Jackson＠nottingham.ac.uk -
shadoooo＠gmail.com