3 Sep
2000
3 Sep
'00
10:16 a.m.
On 2000-09-03 classiccmp(a)classiccmp.org said to kees.stravers(a)iae.nl
I have several TRS-80 Model II (w/ 8" drives)
without keyboards.
Are the Model III keyboards compatible?
No, they need a keyboard that uses a special serial protocol. The
keyboard looks a bit like a Model I.
Also, if anyone wants one of these things, $10 plus
shipping. The
condition is unknown since I haven't fired them up ... and they
don't include keyboards :).
I think I have enough :) see:
http://home.iae.nl/users/pb0aia/cm/modelii.html
Kees.
--
Kees Stravers - Geldrop, The Netherlands - kees.stravers(a)iae.nl
http://www.iae.nl/users/pb0aia/ My home page (old computers,music,photography)
http://www.vaxarchive.org/ Info on old DEC VAX computers
Net-Tamer V 1.08.1 - Registered
3 Sep
3 Sep
11:14 a.m.
New subject: Need bezel for DEC TLZ06-AA
Hi,
I recently purchased a few DEC TLZ06-AA DAT drives, and they arrived
today. Unfortunately, The bezel on them is the width of a 3.5" drive,
but the height of a half-height 5 1/4" drive.
Does anyone know where I can get normal 5 1/4" bezel for them?
Any suggestions on how to mount them in a PC and a uVAX II?
Thanks,
clint
5 Sep
5 Sep
10:45 a.m.
New subject: Need bezel for DEC TLZ06-AA
I recently purchased a few DEC TLZ06-AA DAT drives,
and they arrived
today. Unfortunately, The bezel on them is the width of a 3.5" drive,
but the height of a half-height 5 1/4" drive.
Does anyone know where I can get normal 5 1/4" bezel for them?
Any suggestions on how to mount them in a PC and a uVAX II?
I don't think you're going to be able to get a regular bezel for them, your
best bet would be to take a piece of plastic and fabricate something to go
over the existing one.
Mounting in the PC would be fairly easy I'd think. Just get a 3.5" HD
mounting kit for a 5.25" bay, the same thing would take care of the uVAX II
if you've got the sled for it to go on.
The TLZ06 is a nice drive, I've got one (with the 5.25" bezel) in my
PWS433au, and OpenVMS loves it.
Zane
10:59 a.m.
New subject: Need bezel for DEC TLZ06-AA
On Tue, 5 Sep 2000 healyzh(a)aracnet.com wrote:
I did something similar a while back in order to mount a different tape
drive. The kit had a blank panel that I cut the center out of so that
it would bridge the gap on either end between drive and case. IIRC, I
also needed to relocate some of the screw holes in the adapter to match
the drive involved.
- don
I recently
purchased a few DEC TLZ06-AA DAT drives, and they arrived
today. Unfortunately, The bezel on them is the width of a 3.5" drive,
but the height of a half-height 5 1/4" drive.
Does anyone know where I can get normal 5 1/4" bezel for them?
Any suggestions on how to mount them in a PC and a uVAX II?
I don't think you're going to be able to get a regular bezel for them, your
best bet would be to take a piece of plastic and fabricate something to go
over the existing one.
Mounting in the PC would be fairly easy I'd think. Just get a 3.5" HD
mounting kit for a 5.25" bay, the same thing would take care of the uVAX II
if you've got the sled for it to go on. The TLZ06 is a nice drive, I've got one (with the
5.25" bezel) in my
PWS433au, and OpenVMS loves it.
Zane
8878
days inactive
8880
days old
3 comments
4 participants
participants (4)
-
donm＠cts.com -
healyzh＠aracnet.com -
kees.stravers＠iae.nl -
vaxman＠uswest.net