You'll look for pins on the board to instruct the drives which will be reading and which will be writing. That is my guess. Both need to work and have empty space. Probably the machine booted directly from some type of PXE, but maybe not. This gives you a hint: https://w2hx.com/x/SAIC%20V2LC/20200124_094105.jpg It must power up, that is a good sign. Good luck. On Thu, Jun 25, 2020 at 4:13 PM Jon Elson via cctech <cctech at classiccmp.org> wrote:

On 6/25/2020 11:20 PM, Chuck Guzis via cctech wrote: The drive spec I found for the Conner cfs540a (this drive) shows an operating range of 5c to 55c. The top of the range is useful for mil operations, but the 5c spec would be bad if you ran the drive. Full military just a casual google says is -55c, and extended industrial is -40c on the bottom.? We did -40 specs for some of our projects, but nothing mechanical. The are at -40c to 60c for nonoperating, so would be close to the low range if they could heat the spindle, and let the drive heat itself up. One issue might be that the sensor will heat up this dongle and allow the thing to run, but there may be a provision to spin the drive before it is expected to run.? A heat up or warmup feature might be performed besides what Jon suggested with the heater / sensor. I suspect this thing has to heat up and be at temp before something in the bios or otherwise allows the drive to run. The OP might look around and see if there are any of the heater strips around as well, to allow heating in the drive box as needed. I may have one of these systems with some extra drives, and the good news is they guy I bought them drives in the boxes from random drive buys and they were easy to run.? He didn't recall the spindle dongle on his drive pods though. I'm waiting to hear for sure if the fellow I bought mine from remembers the manufacturer.? The system and an auxiliary box of similar size with more pods came in a deal I couldn't pass up.? My box has got a 486 motherboard and functional 10baseT card running in it.? I plan to use one of the pods to do one of these as solid state to save runtime on the physical disks. spec I used at: ftp://ftp.seagate.com/techsuppt/seagate_utils/allconnr.pdf

Thank you EVERYONE. Yes I confirmed that the red disc is a heater and the little device on the side is a temp sensor. All is good. I will send a new email out with some new questions but wanted to tie off this discussion with thanks to all Eugene -----Original Message----- From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of dwight via cctalk Sent: Friday, June 26, 2020 9:26 AM To: General Discussion: On-Topic and Off-Topic Posts <cctalk at classiccmp.org> Subject: Re: IDE Hard Drive Question I'd measure the temperature sensor. It is most likely a typical thermistor but may be an RTD. Most RTD's are 100 ohm but there are some platinum on ceramic that are 1K ohms. Check it both directions with an ohm meter. It might be a solid state semiconductor type device. If a resistive device, it can likely be replaced by a resistor. If it is 10K thermistor or whatever just replace it with a fixed resistor. Put it in the fridge for a few minutes to see if it is a negative or positive temperature coefficient. Once you know that it should be easy to use a value of resistor that would tell it that is was at a happy 20c. You can likely leave the heater leads open. The temperature sensor is the small black thing. I doubt it is a thermal switch but it might be. It is most likely to be around specific resistances of 10 ohms, 100, 1K or 10K. Dwight ________________________________ From: cctalk <cctalk-bounces at classiccmp.org> on behalf of jim stephens via cctalk <cctalk at classiccmp.org> Sent: Thursday, June 25, 2020 11:59 PM To: cctech at classiccmp.org <cctech at classiccmp.org> Subject: Re: IDE Hard Drive Question On 6/25/2020 11:20 PM, Chuck Guzis via cctech wrote: The drive spec I found for the Conner cfs540a (this drive) shows an operating range of 5c to 55c. The top of the range is useful for mil operations, but the 5c spec would be bad if you ran the drive. Full military just a casual google says is -55c, and extended industrial is -40c on the bottom. We did -40 specs for some of our projects, but nothing mechanical. The are at -40c to 60c for nonoperating, so would be close to the low range if they could heat the spindle, and let the drive heat itself up. One issue might be that the sensor will heat up this dongle and allow the thing to run, but there may be a provision to spin the drive before it is expected to run. A heat up or warmup feature might be performed besides what Jon suggested with the heater / sensor. I suspect this thing has to heat up and be at temp before something in the bios or otherwise allows the drive to run. The OP might look around and see if there are any of the heater strips around as well, to allow heating in the drive box as needed. I may have one of these systems with some extra drives, and the good news is they guy I bought them from if mine are the same or of similar spec, is that he was putting drives in the boxes from random drive buys and they were easy to run. He didn't recall the spindle dongle on his drive pods though. I'm waiting to hear for sure if the fellow I bought mine from remembers the manufacturer. The system and an auxiliary box of similar size with more pods came in a deal I couldn't pass up. My box has got a 486 motherboard and functional 10baseT card running in it. I plan to use one of the pods to do one of these as solid state to save runtime on the physical disks. spec I used at: ftp://ftp.seagate.com/techsuppt/seagate_utils/allconnr.pdf