10 Nov
1999
10 Nov
'99
3:21 a.m.
I just acquired 3 convergent technologies computers. They are a series of
modules that plug together, each module is the size of a very thick book.
They have external power supplies with a 2 foot long cable with snap
connectors to connect power supply to module. The modules plus together
along the side and a latch locks the connection. No tools needed to
add/remove memory. The computers power up and LED's come on. The
information I got from the web doesn't say what kind of CPU chip was used,
what the computers were designed for and if they are still supported. From
several web searches I think these machines ran CTOS which was dropped by
Unisys.
The date on the inside of the cases is 1983 and 1984.
Module 1 CPU with 3 extra memory modules, one labeled datapoint, one
convergent tech, one burroughs
Module 2 Hard disk 10MB ST225
Module 3 5 1/4 floppy drive
Module 1 CPU
Module 2 hard disk 90MB
Module 3 5 1/4 floppy
Module 4 40-60 MB tape drive
I picked up 8 power supplies, and 10-20 cables, no manuals. One cable has
two right angle db9 connectors that seem to be made to connect "cluster
controller" connector in the side of the CPU. Other looks like terminal
cable. Does anyone know what kind of terminal would work? Any other
information would be appreciated.
Thanks
Mike McFadden
12 Nov
12 Nov
11:51 a.m.
On Wed, 10 Nov 1999, McFadden, Mike wrote:
I just acquired 3 convergent technologies computers.
They are a series of
modules that plug together, each module is the size of a very thick book.
They have external power supplies with a 2 foot long cable with snap
connectors to connect power supply to module. The modules plus together
along the side and a latch locks the connection.
These are members of Convergent's NGEN workstations. They use intel CPUs
and are not related in any way to their more well-known Mini- and
MitiFrame computers.
information I got from the web doesn't say what
kind of CPU chip was used,
what the computers were designed for and if they are still supported. From
several web searches I think these machines ran CTOS which was dropped by
Unisys.
What little information you have found is correct and is about as much as
I know myself. The machines seemed to be popular at banks but this is all
hypothetical knowledge. They are not still supported. Eventually the
systems evolved from the hardware you have in front of you to a "CTOS
Executive" software module running under Windows NT on a generic
Pentium-class system.
The date on the inside of the cases is 1983 and 1984.
Module 1 CPU with 3 extra memory modules, one labeled datapoint, one
convergent tech, one burroughs
With those dates, you most likely have a CM001 CPU which has an intel
80186 processor inside. The 001/8 runs at 8 MHz and the 001/6 runs at 6
MHz. The memory modules are most likely 256k apiece, and the machine
should have 256k RAM built into the CPU. As somebody else mentioned,
Burroughs made an identical line of machines under their own label.
two right angle db9 connectors that seem to be made to
connect "cluster
controller" connector in the side of the CPU. Other looks like terminal
cable. Does anyone know what kind of terminal would work? Any other
information would be appreciated.
I couldn't guess what sort of terminal might be used. The machines are
foreign enough to me that I have only a vague idea of how to run one, and
all my systems use dedicated display hardware for their consoles. I'm not
sure serial consoles are supported, though I have no proof of this, one
way or the other.
Any revelations you might have I would be interested in hearing, as the
three different models of these machines I have are equally as baffling to
me as I'm sure yours are to you. (:
ok
r.
9172
days inactive
9174
days old
1 comments
2 participants
participants (2)
-
mmcfadden＠cmh.edu -
red＠bears.org