8 Jan
2022
8 Jan
'22
5:26 a.m.
To make testing of the H744 a bit easier I would like to try to make up some
connectors for the mate-n-lok connector to make it easier to connect power
and load. I know the H744 uses a mate-n-lok connector, but there seem to be
a lot of different types and I don't seem to be able to find a type that
would work. Does anyone know what the correct one is?
Thanks
Rob
8 Jan
8 Jan
5:36 a.m.
See the bottom of:
https://gunkies.org/wiki/DEC_standard_modular_regulators
I believe that you'll want one or more of these:
https://www.connectorpeople.com/Connector/TYCO-AMP-TE_CONNECTIVITY/1/1-48046
0-0
https://www.connectorpeople.com/Connector/TYCO-AMP-TE_CONNECTIVITY/1/1-48045
9-0
Note that both have a minimum order :-<. As for pins:
https://www.mouser.com/ProductDetail/TE-Connectivity/60620-1?qs=pn%2Fzyis3Xj
HkDeV60Xt%252Btg%3D%3D
https://www.mouser.com/ProductDetail/TE-Connectivity-AMP/60619-1?qs=sGAEpiMZ
ZMueQxo7L%2FBPyOx7s9t3UY8b
-----Original Message-----
From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Rob Jarratt via
cctalk
Sent: Saturday, January 8, 2022 8:27 AM
To: General Discussion: On-Topic and Off-Topic Posts <cctalk at classiccmp.org>
Subject: Mate-n-lok connector for H744 Regulator
To make testing of the H744 a bit easier I would like to try to make up some
connectors for the mate-n-lok connector to make it easier to connect power
and load. I know the H744 uses a mate-n-lok connector, but there seem to be
a lot of different types and I don't seem to be able to find a type that
would work. Does anyone know what the correct one is?
Thanks
Rob
5:44 a.m.
Note that both have a minimum order :-<. As for
pins:
If folks don't want to deal with minimums, we can make up cables with the correct
connector, we stock the housings, crimps, and have the correct TE crimp tool for them.
That said, connectorpeople.com are good to deal with, we use them for weird connectors.
Their checkout process is...not Web 2.0 :)
Thanks,
Jonathan
7:33 a.m.
I have a cabinet full of 'parts' regulators if anyone is local to
landenberg, pa (btwn phila/baltimore) and would like one to use for parts,
selling for a reasonable cost (make offer) or trade. Contact me privately
through vintagecomputer.net. I also have a limited supply of NOS Sprague
caps for these. I probably have more 744s than anything else.
Bill
On Sat, Jan 8, 2022, 8:54 AM Jonathan Chapman via cctalk <
cctalk at classiccmp.org> wrote:
Note that both
have a minimum order :-<. As for pins:
If folks don't want to deal with minimums, we can make up cables with the
correct connector, we stock the housings, crimps, and have the correct TE
crimp tool for them.
That said, connectorpeople.com are good to deal with, we use them for
weird connectors. Their checkout process is...not Web 2.0 :)
Thanks,
Jonathan
844
days inactive
844
days old
3 comments
4 participants
participants (4)
-
billdegnan＠gmail.com -
lists＠glitchwrks.com -
pbirkel＠gmail.com -
robert.jarratt＠ntlworld.com