2 Jan
2004
2 Jan
'04
5:46 p.m.
22 Feb
22 Feb
10:01 p.m.
New subject: Everex EV-831
I've tried to find DOS drivers for this QIC-36 card, but as yet to no avail.
Could someone give me an idea on where to find one ? I've only seen some
Unix and BSD drivers.
Any ehlp would be appreciated
23 Feb
23 Feb
1:42 a.m.
New subject: Everex EV-831
Let me know how you make out with that Nico, Ive got like 3-4 of them
and some QIC02's as well.
Curt
Nico de Jong wrote:
I've tried to find DOS drivers for this QIC-36
card, but as yet to no avail.
Could someone give me an idea on where to find one ? I've only seen some
Unix and BSD drivers.
Any ehlp would be appreciated
--
Curt Vendel & Karl Morris
-----------------------------------------------------------------------
The Atari Museum
http://www.atarimuseum.com
The Atari Explorer
http://www.atari-explorer.com
6:51 a.m.
New subject: Everex EV-831
there weren't a lot of dos drivers for the 831. The everex backup and restore
program pretty much was the way that you used the tape drive under DOS.
I don't recall if everex made available drivers, or if you had to come by them
on your own.
Jim
Curt Vendel wrote:
Let me know how you make out with that Nico, Ive got
like 3-4 of them
and some QIC02's as well.
Curt
Nico de Jong wrote:
I've tried to find DOS drivers for this QIC-36
card, but as yet to no avail.
Could someone give me an idea on where to find one ? I've only seen some
Unix and BSD drivers.
Any ehlp would be appreciated
-- 
12:30 p.m.
New subject: Everex EV-831
Hi, gang,
*********** REPLY SEPARATOR ***********
On 23-Feb-04 at 11:51 jim wrote:
there weren't a lot of dos drivers for the 831.
The everex backup and
restore program pretty much was the way that you used the tape drive under DOS.
I don't recall if everex made available drivers, or if you had to come by
them on your own.
Fortunately, I used to run that setup in an old system I once had. I just sent
Nico some ZIPfiles from my archives that should do the trick.
Yes, Everex did, at one time, provide drivers. However, the tape software
manufacturers, such as Sydex and Mountain, also incorporated such into their backup
software.
I'm glad I've turned into such a pack rat... It's amazing what can
help someone out these days...
-=-=-=-=-=-=-=-=-=-=-=-
Bruce Lane, Owner & Head Hardware Heavy,
Blue Feather Technologies -- http://www.bluefeathertech.com
kyrrin (at) bluefeathertech do/t c=o=m
"If Salvador Dali had owned a computer, would it have been equipped with surreal
ports?"
10:42 a.m.
New subject: Everex EV-831
Let me know how you make out with that Nico, Ive got like 3-4 of them
and some QIC02's as well.
If that's the board I think it is, then it's actually ISA->QIC02 and
QIC02->QIC36 interfaces on the same board. There's a tiny QIC02 bus in
there...
The design of the QIC02->QIC36 part is _very_ similar to a standalone
QIC02->QIC36 interface I have -- I think it's badged Wangtek. I used that
on my PERQ for a time, after patching the EPROM so that it defaulted to
QIC11 format (whcih is what the PERQ distribution tapes are).
-tony
7864
days inactive
7915
days old
5 comments
6 participants
participants (6)
-
aek＠spies.com -
ard＠p850ug1.demon.co.uk -
curt＠atarimuseum.com -
jwstephens＠msm.umr.edu -
kyrrin＠bluefeathertech.com -
nico＠farumdata.dk