FW: FS or donate: (2) DEC PDP-11/23 minicomputers, Durham NC

>FS or donate: (2) DEC PDP-11/23 minicomputers, Durham NC >I have for sale or donation a *package* of PDP-11/23 minicomputers and >software: >* The PDP-11/23 system (all 18-bit, I think): > 1 M8186 LSI-11/23 CPU card, MMU but no FP chip. > 1 M8059FC 128Kx16bit memory card ? > 2 M8044 32Kx16bit memory card > 1 M8043 DLV11-J quad serial line controller > 1 M8013 RLV11 RL02 disk controller (2 card set) > 1 M8014 " " " " > 1 M8012YA BVD11YA backplane controller with ROM, clock, etc >* The PDP-11/23 PLUS system (looks almost brand-new): > 1 M8089 PDP-11/23+ CPU card with MMU, FP and CIS chip sets > 1 M8067KB MVS11-P memory, 256Kx22bit > 1 8061 RLV12 RL02 disk controller > 1 M7957 DZV11-J controller > 2 RL02 disk drives > 15 RL02 disk packs (10Mb each) > 1 bus extension card (pushes the card outside the cabinet) >* Other hardware > 1 RX02 dual 8" disk drive with controller card > 2 4x9 slot card cages, one 18-bit bus, one 22-bit. Both have > heavy duty power supplies, fans, power/reset/halt switches. > 1 4'x19" DEC rack > 1 single height blank panel > 4 sets of sliders > The rack holds 6 single height modules: the CPUs' card cages > are all single height, the disks are all double height. The rack > comes with a filtered, remote-switched power distribution panel. > National Semi Q-bus 22-bit, 512KB memory bought at TCF in 1990 or so. >* Books/software: > Old RT-11 (Version 4.1?) distribution on RL02 and RX02 media > Includes all kernel sources and macro assembler. > Fortran, basic, DIBOL (DEC COBOL) and a few other things > Complete RT-11 manual set (3 feet of binders) plus assorted PDP > data books and other stuff > Complete schematics for an 11/23+ (this is the field set). > BSD2.9 manuals > My docs are all 1983/1984 vintage, which is fine for the boards I > have, but they don't document newer Q-bus stuff. >==== >>>> I am asking $199 or BEST OFFER for the package. <<<< >It all must go as a LOT -- no piecemeal sales. >You'll need a full-size pickup truck, a industrial-grade hand-truck >and two strong bodies (hopefully not including mine). >I would like to get this equipment to someone who will *use it*, as >opposed to someone who wants one board or manual and will put the >remainder in a dumpster. The buyer should at least *properly recycle >the equipment* that is not needed. >Most of it was working when obtained. I saw the 11/23 system booted >and running off the RL02s, under RT-11 (in 1991). The 19" rack has >been sitting crated since that time (without any computer equipment >inside) in the damp basement of my house -- I have no idea of its >current condition. Everything else is upstairs, in the way... >I'm located in Durham, North Carolina, very close to I-85 (2.5 hours >to Richmond VA, 4+ hours to D.C., 9 hours to NYC by car). >EMAIL: biggers(a)_no_spam_saiph.com > (remove the anti-spam to reply, thanks!) >or CALL 919-286-1441 >----mark