Fujitsu M2442AC tape drive and Emulex QT13 controller issues...

On Fri, May 14, 2010 at 9:17 AM, P Gebhardt <p.gebhardt at ymail.com> wrote: I hooked my QT13 up to my M2444AC and installed the QT13 in a BA213 with a KA660 and ran the QT13 diagnostics in system console mode. I had a scratch tape mounted in the M2444AC and all of the diagnostics completed successfully, which took 20-30 minutes. The captured console output is listed below. The QT13 was configured with the following switch settings at power up. SW-1 was toggled from OFF to ON and back to OFF just prior to the "ST 80" console command. SW1-1 OPEN(OFF) away from PCB SW1-2 CLOSED(ON) near to PCB SW1-3 CLOSED(ON) near to PCB SW1-4 CLOSED(ON) near to PCB SW2-1 OFF SW2-2 OFF SW2-3 OFF SW2-4 OFF SW2-5 ON SW2-6 OFF SW2-7 ON SW2-8 OFF KA660-A V4.9, VMB 2.12 1) Dansk 2) Deutsch (Deutschland/?sterreich) 3) Deutsch (Schweiz) 4) English (United Kingdom) 5) English (United States/Canada) 6) Espa?ol 7) Fran?ais (Canada) 8) Fran?ais (France/Belgique) 9) Fran?ais (Suisse) 10) Italiano 11) Nederlands 12) Norsk 13) Portugu?s 14) Suomi 15) Svenska (1..15): 5 Performing normal system tests. 95..94..93..92..91..90..89..88..87..86..85..84..83..82..81..80.. 79..78..77..76..75..74..73..72..71..70..69..68..67..66..65..64.. 63..62..61..60..59..58..57..56..55..54..53..52..51..50..49..48.. 47..46..45..44..43..42..41..40..39..38..37..36..35..34..33..32.. 31..30..29..28..27..26..25..24..23..22..21..20..19..18..17..16.. 15..14..13..12..11..10..09..08..07..06..05..04..03.. Tests completed. Scan of Qbus I/O Space -20001468 (772150) = 0000 RQDX3/KDA50/RRD50/RQC25/KFQSA-DISK -2000146A (772152) = 0B20 -20001940 (774500) = 0000 TQK50/TQK70/TU81E/RV20/KFQSA-TAPE -20001942 (774502) = 8051 -20001F40 (777500) = 0020 IPCR Scan of Qbus Memory Space ***** ***** EMULEX CORPORATION * * 3545 Harbor Boulevard ***** * ***** P.O. Box 6725 * * Costa Mesa, CA, 92626 ***** ***** (714) 662-5600 E M U L E X QT13/14 Firmware Revision K Copyright 1988 EMULEX CORPORATION All rights reserved ---------------------------------------------------------------------------- Unit is Offline CSR Address = 174500 oct ---------------------------------------------------------------------------- Video Display or Hardcopy Terminal (V/H,def=H) : H MAIN MENU ========= A - All tests R - Retry limit value N - NOVRAM Maintenance T - Test selection Menu S - Display Switch settings Q - Quick test on positioning and erase X - Exit Maintenance mode after resetting switches CTRL/C - Returns you to the previous level CTRL/U - Deletes current input if no <CR> entered Select Function (def=A) : S Functions selected by indicated switch settings ----------------------------------------------- Switch 1 Off On _______ | | | [ ] | - 1 --- QT13/14 Tape coupler reset switch, Unreadable Hardware switch | [ *] | - 2 --- Diagnostic mode | [ *] | - 3 --- Host console communications | [ *] | - 4 --- uVAX host | | ------- Functions selected by indicated switch settings ----------------------------------------------- Switch 2 Off On _______ | | | [* ] | - 1 -| | [* ] | - 2 -|- Address = 174500 oct | [* ] | - 3 -| | [* ] | - 4 --- TMSCP | [ *] | - 5 --- Enable 22 bit addressing | [ ] | - 6 --- WDS Trailing edge select, Unreadable Hardware switch | [ ] | - 7 --- WDS Leading edge select, Unreadable Hardware switch | [ ] | - 8 --- Not used, Unreadable Hardware switch | | ------- MAIN MENU ========= A - All tests R - Retry limit value N - NOVRAM Maintenance T - Test selection Menu S - Display Switch settings Q - Quick test on positioning and erase X - Exit Maintenance mode after resetting switches CTRL/C - Returns you to the previous level CTRL/U - Deletes current input if no <CR> entered Select Function (def=A) : N Drive type, 0=Start-Stop, 1=Streamer (0-1,def=1 dec) : On the fly commands (Y/N,def=Y) : Enable data busy timeout delay (Y/N,def=Y) : Remote density (Y/N,def=Y) : CDC tape drive (Y/N,def=Y) : Use IDEN line to select remote density (Y/N,def=N) : IDEN line true selects high density (Y/N,def=N) : Adaptive DMA (Y/N,def=Y) : Blank Tape Timeout value, in seconds (1-60,def=5 dec) : Max retry count for tape errors (0-10,def=8 dec) : uSec Delay between DMA bursts (2/4,def=4) : Enable write data prefill (Y/N,def=N) : Adaptive DMA threshold (1-7,def=4 dec) : Tape Drive Speed thousands of bytes/second (0-65535,def=200 dec) : Support 800 BPI Density (Y/N,def=N) : Support 1600 BPI Density (Y/N,def=Y) : Support 6250 BPI Density (Y/N,def=Y) : Modify ? (Y/N,def=N) : MAIN MENU ========= A - All tests R - Retry limit value N - NOVRAM Maintenance T - Test selection Menu S - Display Switch settings Q - Quick test on positioning and erase X - Exit Maintenance mode after resetting switches CTRL/C - Returns you to the previous level CTRL/U - Deletes current input if no <CR> entered Select Function (def=A) : A Ensure tape loaded and at BOT Press <CR> to continue... * WARNING *, Use scratch tape only, data on tape will be lost Are you sure ? (Y/N,def=N) : Y Enter number of loops to execute (0-255,def=1 dec) : 1 Retry limit of 10 --> Start of pass 1 BOT/Rewind test Write/Read test File mark test Space forward/reverse test Positioning test Erase test Host memory DMA test --> End of pass 1 Executing pass 1 Test Summary: Total # of errors = 0 (0 Hard, 0 Soft, 0 Device, 0 DMA)