I've missed part of this thread so I may make some wrong assumptions here
but I'll throw in what I know about this stuff.
DataI/O has both a software PALASM and a hardware PALASM. I have both
of them and the docs for them. They appear to do the same thing and I don't
what the differences are but there probable are some. I just got this stuff
recently and I haven't had time to learn all the details about it. The
software versions are called Abel and the was available in PCDOS, UNIX and
VAX VMS versions. I have the Abel PC DOS version ($895!) The hardware
PALASM is called a PALASM Design Adapter and is PN 303-100 ($395). It's a
unit that plugs into a DataI/O model 29 programmer and the unit with the
socket for the PAL plugs into it. There are a number is different PAL
socket units. Some of them only work with a few PALs but the one that I
have is a DataI/O model 303A-011 and it seems to work with most PALs. I
also have the manuals for it and the model 29 programmer. I also have a
DataI/O UniPak EPROM socket adapter and LogicPak adapter and I THINK I have
the manuals for them. I also have the manual for the 303A-002 P/T adapter
(one of the PAL sockets) but not the hardware. You MUST have the manuals to
use the DataI/O stuff since the manuals contain the codes that you have to
enter into the programmer in order to tell it what kind of device you're
using. I can make copies of what I have for the cost of copying and postage
if anyone needs them.
Joe
At 09:11 AM 8/10/00 -0600, Dick wrote:
Please see embedded renarks below.
Dick
----- Original Message -----
From: John Honniball <John.Honniball(a)uwe.ac.uk>
To: <classiccmp(a)classiccmp.org>
Sent: Thursday, August 10, 2000 4:34 AM
Subject: Re: Palasm?
On Wed, 9 Aug 2000 12:51:23 -0600 Richard Erlacher
<richard(a)idcomm.com> wrote:
A plug in module for PALASM? What would give you
that idea?
Well, as I recall, that's what written on the module :-)
> I've seen only
> one place on a model 29 for anything to plug in, and that's the
programming
site.
(there are several different ones)
That's right, it's a huge plug-in module to go in the
programming site socket. It has another plug-in module on
top to accept the PALs that are being programmed.
It's been a while but the site does, in some cases have an optional socket
adapter for differing packages. Unfortunately this type of adapter was
needed in some case while other required an etirely different site to
accomodate a given package, i.e. you might need several site/adapter
combinations to handle all the different packages in which a given part was
available.
> The data was typically fed to the
> Model 29 via a serial port, and in JEDEC form. The model 29 translated
the
jedec
file into whatever signals were needed to program the device.
As I have no manual, I can't tell how this thing was
supposed to work.
There was software, in my experience, running on a PC, that told the
programmer what to do, specifically how to drive the device pins and how to
process the JEDEC file. It also sent the JEDEC file once that was set up,
but these were separate steps. At the time I seriously began using
field-programmable logic devices (once price came down) there were
sufficiently inexpensive programmers from second-rank independent vendors
that the model 29 was unrealistic for someone not programming in a prduction
environment and whose needs involved a wide range of devices.
It's not unusual to see these model 29's at distributors' sites. Perhaps
one of your local electronic distributors' technicians can help you out.
The way to do that is to contact someone you know and tell them what you
want is to find whatever documentation there is on the model 29 and
examine/copy it. The guy at the will-call counter will probably be more
helpful than the phone-sales person.
> The last time I used a model 29 was in
'85. They were already pretty
old
> back then and wouldn't program the then
new Altera parts and Lattice
parts I
> was using. That was later fixed, but too
late for me. I bought a
cheapie
that
still works . . .
I've since acquired a Stag PPZ Universal Programmer.
6809-based machine with built-in CRT.
> Is there a feature that plugs in the intelligence to compile Palasm
files
into the
JEDEC? I'd be VERY surprised to learn that.
I'll have to pop up into the loft and fetch this thing down
for a closer look (info in this e-mail is from memory).
I'll post model numbers, etc, in case anybody can identify
the module and tell me I've got it all wrong :-)
--
John Honniball
Email: John.Honniball(a)uwe.ac.uk
University of the West of England