16 Nov
2003
16 Nov
'03
1:20 p.m.
no you have to pop them out to put them in a prom reader!
I know they are there... the system would not have worked as an access
system had they not!
we need a set of hardware manuals for the 2100... it seems though the
passing of the years the old ones I had at computer exchange Inc. let the
earth...
I DID find though the 2100 hardware training manual # 02100-90159 while
looking at home here for the infamous DEC master Module List.... When I
retired I squirreled bits of manuals all over where I live... Most have
been added to the museum's reference library but it seems every time I go
digging I find something.new I know the 2100 processor manuals are gone
though as they were in the HP binders.... kind of hard to loose those!
ed sharpe archivist for smecc
----- Original Message -----
From: "Jay West" <jwest(a)classiccmp.org>
To: <cctalk(a)classiccmp.org>
Sent: Sunday, November 16, 2003 7:09 PM
Subject: Fw: Grandfather system RTE6/VM?
and
----- Original Message -----
From: "Jay West" <jwest(a)classiccmp.org>
To: "Ed Sharpe" <esharpe(a)uswest.net>
Sent: Sunday, November 16, 2003 8:08 PM
Subject: Re: Grandfather system RTE6/VM?
> You don't have to pop out the chips, just pull out the rom card, A1 or
A2,
I
> think it's A2 going from memory. Look at the card and see what numbers
are
on the white
and gold chips that are socketed :)
J
----- Original Message -----
From: "Ed Sharpe" <esharpe(a)uswest.net>
To: "General Discussion: On-Topic Posts Only" <cctech(a)classiccmp.org>
Cc: <jwest(a)classiccmp.org>
Sent: Sunday, November 16, 2003 5:31 PM
Subject: Re: Grandfather system RTE6/VM?
> well I have the set that is in the 2100 in the 2000 access system
here.
> > not a loose set. ( shall we call it embedded?)
> >
> > I would live in fear of poping them out though......
> >
> > ed!
> >
> > ----- Original Message -----
> > From: "Jay West" <jwest(a)classiccmp.org>
> > To: "ed sharpe" <esharpe(a)uswest.net>et>; "General Discussion:
On-Topic > > Off-Topic Posts"
<cctalk(a)classiccmp.org>
> > Sent: Sunday, November 16, 2003 12:07 PM
> > Subject: Re: Grandfather system RTE6/VM?
> >
> >
> > > You're quite sure you have a set of the IOP firmware for the 2100
cpus
> Ed?
> > > If so, good to know. I really want to get mine backed up as they
seem
to
2100
> be
> > the only ones around. However, I got a new prom burner and it is
acting
> > very
> > > flaky so I'm a little afraid to put my chips in it.
> > >
> > > Jay
> > > ----- Original Message -----
> > > From: "ed sharpe" <esharpe(a)uswest.net>
> > > To: "General Discussion: On-Topic and Off-Topic Posts"
> > > <cctalk(a)classiccmp.org>rg>; <classiccmp(a)classiccmp.org>
> > > Sent: Saturday, November 15, 2003 11:16 PM
> > > Subject: Re: Grandfather system RTE6/VM?
> > >
> > >
> > > > we have a set too Al, but alas no way to read them....
> > > > It is up to you Jay!
> > > > ed!
> > > > ----- Original Message -----
> > > > From: "Al Kossow" <aek(a)spies.com>
> > > > To: <classiccmp(a)classiccmp.org>
> > > > Sent: Saturday, November 15, 2003 5:54 PM
> > > > Subject: Re: Grandfather system RTE6/VM?
> > > >
> > > >
> > > > >
> > > > > > I'll try to dump the microcode proms this weekend
> > > > >
> > > > > Dumps of the firmware is now up at
> www.bitsavers.org/HP/1000_firmware
> > > > > including the IOP firmware the 21MX.
> > > > >
> > > > > Jay, since you appear to have the only surviving copy of the
IOP
> >
firmware, it would be good to get the proms read.
> >
> >
> >
>
>
>