28 Oct
1998
28 Oct
'98
8:23 a.m.
On Wed, 28 Oct 1998, Tony Duell wrote:
Ok, an 8- or even 16-port hub can be had for around $100 or less.
The Coax is no harder to install than twisted pair.
It's no more likely
to be stepped on and there are proper wallplates etc if you're worried
about it getting pulled. And I find the strain relief on the BNC to be a
lot better than that on an RJ45.
I don't. Its far easier for a coax to get pulled out of the BNC connector
than it is for a twisted-pair cable to be pulled out of an RJ-45.
Hmm.. Fitting a plug on a piece of twisted pair behind
a machine rack is
not fun. 8 wires to get into the right channels, brown and orange colours
to tell apart, no thank you.
The BNC was _designed_ to be trivial to fit, actually. The best way to do
it is to use a solder type plug and ignore the instructions :-). Then :
Put the nut and rubber washer over the cable. Remove about 3/4" of the
outer covering. Fan out the braid, put the T-shapped ferrule over the
inner insulator and push it down inside the braid. Trim off the braid
around the outside of the ferrule, cut the inner insulation (but not the
inner wire) flush with the end of the ferrule (use a sharp knife for
this), pull off the inner insulation, tin the centre wire. Put on the
little disk insulator, cut the inner wire a couple of mm beyond that, put
the pin on, solder in place. Put the outer insulator and plug body on the
end of that, slide up the nut/washer and tighten it all up.
So you're saying its easier to work with a soldering iron, solder, a pair
of dykes, a knife and a 3-piece BNC connector behind a machine rack, as
opposed to a one-piece RJ-45 that requires one tool to cut, strip and
crimp? Wow. You ARE a glutton for punishment.
It took longer to type that than it does to do it.
I can crimp a BNC connector in a few seconds with the right tool, and I
don't bother with the soldering. Crimping seems to do the trick quite
nicely.
A couple of tips. Get the right cable and plugs. There
are several sizes
of BNC plug (not just 50 Ohm and 75 OHm - acutally different sizes of
ferrule, etc) to fit different cables. A lot of hassles start when you
use the wrong plug. Also get a couple of the special flat spanners for
tightening up the plugs. A lot easier than trying to use pliers.
And don't use any cable other than RG-58A/U or RG-58C/U for thinnet. If
you use anything else (i.e. straight RG-58) you're going to start running
into trouble if you begin to add nodes or have long distances in between
nodes.
Anyway, with 10 base T, there may be a dozen cable
coming out from the
room where the bub is to other machines in the house. With 10 base 2,
there's normally only one coax cable.
Like I said, as long as you are connecting computers that are within a few
feet of each other then coax is a good choice.
around
corners, over door frames, etc. And 4-port hubs can be had for
less than $50 these days. A worthwhile investment for having a more
_4_ port hubs??? Surely you jest :-). Us workstation types have 4
machines per desk with ethernet ports :-). Since when have any _classic_ computers had 100Mbps
network ports? Heck,
I'm looking out for any original 3Mbps stuff :-)
Which reminds me. 10 base 2 is on-topic here (over 10 years old). I am
not so sure about 10 base T
Well, ten years from now you'll regret using coax when you want to plug
that Pentium II with a PCI 100baseT ethernet card onto your network :)
Sellam Alternate e-mail: dastar(a)siconic.com
-------------------------------------------------------------------------------
Ever onward.
Coming in 1999: Vintage Computer Festival 3.0
See http://www.vintage.org/vcf for details!
[Last web site update: 09/21/98]
Of course, this assumes your machine can use
100baseT. Old machines like
your PERQs and PDP11's would be quite happy with 10baseT.
I thought this was classiccmp....