5 Apr
2020
5 Apr
'20
1:18 p.m.
On 2020-Apr-05, at 6:05 AM, Rob Jarratt via cctalk wrote:
I found time to follow Mattis?s suggestion today and I
got some interesting results.
I powered the UC3842 with about 16V from a bench power supply. I lifted R32 so that the
transformer would not supply it. I then used an isolating transformer to power a variac
and applied the variac to the AC inlet. I also used a load board from a MicroVAX 2000 and
an old RD53 disk as the load, so there should be enough load.
I found that I can vary the AC input up to a maximum of about 40VAC before the SCR
triggers, the 5V output reaches about 400mV. If I raise the AC input more slowly, it will
usually cut out before that, around 30VAC. I noticed that the inrush thermistors also get
quite hot at these low AC voltages, I don?t know if this is because of the relatively low
AC supply voltage, or if this indicates a problem of some kind.
The voltage coming out of L3 into the T1 ?bounces? somewhat. I guess this is because the
AC input is only 20V or so, or it may be expected ripple from the smoothing capacitors? In
the description below, the peaks of the bounces are used. Throughout the variation from
0VAC to 40VAC the duty cycle of the oscillation of the UC3842 output does not change, I
guess because the output voltage has not reached its target value.
With the AC input at about 25VAC the circuit seems to be stable (apart from the bounces
mentioned above). At this supply voltage, the voltage at the source of Q1 reaches 2V. The
current sense resistor is 1 Ohm, which means 2A must be flowing through it at that time.
When the Q1 source is at 2V, the other end of R14 is at about 0.5V, which is just below
the trigger voltage for the SCR. This makes sense because R14 and R15 form a voltage
divider that looks to be nominally 25% of the Q1 source. Given the SCR nominally triggers
at about 0.8V, this means that the current sense resistor is set to trigger the SCR at
about 2.5A, I think. This would suggest that the duty cycle on Q1 is too high and causing
too much current to be drawn. So presumably the feedback to the UC3842 is not working
correctly.
I tried setting the AC input at 120V and using a one-shot sample. Q1 is switched for
about 30ms and then there is a spike on the SCR gate to 2V and it triggers. The gate
voltage then remains at 1V. However, there is no spike across the current sense resistor
(R13), so I don?t know if the spike is because the SCR is being turned for some other
reason. There is nothing unusual on the anode of D19 to cause it to trigger due to
avalanche breakdown. I got the same result when the AC input was 220V. I wonder if the SCR
is behaving slightly differently because I have lifted R32?
Since there might be a feedback problem, I looked at the VFB input to the UC3842 when
doing a one-shot test at 240VAC. I can see VFB steadily rise over the period when Q1
switched, up to a maximum of 4V. I don?t really know if this is how it should behave
though, but it seems to make logical sense. During all that time the duty cycle of Q1 does
not change.
I am not too sure where to go from here. I hope the above makes sense. I would appreciate
any further thoughts.
Switching power supplies are, to coin a phrase, voltage/current-ratio power translators.
They will attempt to adjust the (cycle-averaged) input-current demand in inverse
proportion to the input voltage, to meet the power demand of the load.
When you load a switching supply, and run it with a low input voltage, it will attempt to
increase the input-current demand, either with increased peak current or increased
duty-cycle (ON-time of primary switching transistor(s)).
Suppose you have a load demand of 100W. At 100V input the input current needed is 1A.
At 10V input, the input current needed is 10A.
If a supply is not explicitly designed for low supply voltages, it can lead to excessive
primary-side currents.
This is why it is a bad idea to 'run up' switching supplies from a variac or
otherwise run them outside their specced input voltage range.
You don't say what the observed duty-cycle (ON-time) is. What would be expected is
it's running 'wide-open' because it's trying to get enough energy through
the transformer to meet the load demand while gasping for resources from the input because
the input voltage is so low.
So from the scenario you've set up, it's difficult to discern whether the
behaviour is normal or faulty (the scenario masks the otherwise-observed faulty
behaviour).
All this is also dependant on how large your dummy load is (as a % of the rated max power
output of the supply).
If you want to run at a low input voltage, remove or very lightly load the output.
From your schematic, there is a small load presented
internally from various voltage dividers around the outputs, although not all the R values
are in the schematic, so can't calc the current.
If you still get the
over-current SCR triggering, suspicion could lean towards a short somewhere - a winding in
the main transformer, secondary rectifiers or caps - anything presenting an excessive
energy sink to the main switcher, including over-sensitivity of the crowbar circuits on
the secondary side. The secondary crowbar circuit monitors the output voltages relative to
a reference. You could scope-monitor the gate of the SCR over there.
The spike you mention on the primary-side SCR gate without a corresponding spike on R13
does seem odd, seeing scope traces pic could be interesting, perhaps scope the anode, the
gate and R13. Possibility of some odd trigger fault in the SCR.
There is a small amount of filtering on the SCR-gate/over-current voltage divider
(C18/2.2nF) so you would expect to a slightly averaged version of the voltage at R13 after
the voltage divider (at the cap/gate).
Aside: You have R27 & R28 at 20+20 ohms in your schematic. This is an awfully low R
for dropping the hundreds of supply V down to the 16V/low-current of the 3842 supply. For
schematic accuracy, you might double-check the value of those.
10/10 for your tenacity in this repair attempt.