8 Jul
2005
8 Jul
'05
2:32 a.m.
My recollections and recommendations...
The boot rom for the DSD drive is already on the 9312 from the 11/34
system. It is a standard DEC rom, I think RX02.
Also, use the MOS memory from the 11/34 to boot. I'd recommend you
boot from the DSD drives, or one of the RL01's. You have several
bootable RL01 packs, but there are still two or three left here.
One of the packs that's still here is the one that has the driver source
for the LincTape drive.
I never had a boot rom for the Linc, and its not really a practical boot
device for RT-11.
No cable for the DSD setup eh? Hmmm, must still be in the garage....
It is a normal ribbon cable just as you suspect.
As best I recall, the LincTape II supports both DecTape and LincTape
formats (they are not the same). Way back in the Eli Heffron days
I used to get requests to transfer data from Linc or DecTape and
copy it onto RX02's, but this became painful and we stopped doing
this 'service'. The drives you have (LincTape II and DSD) are the
very drives I used for this.
I have a bunch of media for the LincTape II drive. Al K. 'borrowed'
several tapes that had something of interest when he picked up the
MIT CADR as well. But there are still many tapes here you need to
get.
As for mounting the RL01, there is still an H-960 sitting here!
I think I also have a box of floppy disks for the DSD setup.
You did get the OMSI Pascal packs, right?
----- Original Message -----
From: "Jay West" <jwest at classiccmp.org>
To: "General Discussion: On-Topic and Off-Topic Posts"
<cctalk at classiccmp.org>
Sent: Thursday, July 07, 2005 5:55 PM
Subject: 11/45 is alive (I'm singing "who's johnny")
The /45 lives, got a console up with the console
emulator today. I never
did get a blinking lights program to show up right, but I'm too embarassed
to admit what likely caused that. But I got a lot of other few instruction
programs to work correctly so I moved on to the DL11 and 9312 setup and
got it all working. Only have 8K of core, but hey, it's a start. Once I
get it to boot from a peripheral I'll take out the loaned cpu set and move
mine back in and see where it chokes.
So now I have a few peripheral questions. I was going to put in an RL02
drive, but I've been advised against putting one in the same cabinet as
the cpu cab is top cooling intake :\ Now I'm moving on instead to hooking
up and testing a LincTape II and a DSD440 drive. I found the docs for the
DSD440 drive on bitsavers; my drive is missing the controller to drive
cable. From those docs it appears to be a straight through 2x13 pin berg
connector at each end. Can anyone confirm this? Also, If the DSD440 drive
is set for RX01, will it work with the standard dec boot rom (DX) on the
9312? Likewise, if it's set for RX02 emulation will it work with the DY
boot room on the 9312? Or does the DSD440 need a unique bootrom?
I also have the LincTape II & controller (&cable), model CO-3000D.
However, I don't see any docs for it on bitsavers and my googling gives
tons of stuff on the Linc, not the LincTape II. Does anyone have docs for
the LincTape II in electronic format? Or better yet... a boot rom for it
:>
I have spare boot roms (DP, RP02/03 and DM, RK06/07) that I doubt I'll
ever use and would be available for trade.
Thanks!
Jay West