AT&T 3B2 floppy format

It looks like you did everything right. However I thought one specifies interleave directly in the BIN2IMD command using the DM=3 option. I see you have DM=4 on your command line. But since you can load the kernel that might not be the source of your problem. Having a disk being formatted in one drive not readable in another could simply be that one of the two drives is misaligned. Or some silly difference with the track width between the two heads of your later HD drive and the earlier QD drive, although since they are both 80 tracks that should not be. BTW, can you do the reverse, format a disk in your AT&T and recover every sector through IMD on your PC? In this case there might be an option in ImageDisk to write without formatting. I think you can do that with Omnidisk. Marc From: cctalk <cctalk-bounces at classiccmp.org> on behalf of Seth Morabito <lists at loomcom.com> Reply-To: "cctalk at classiccmp.org" <cctalk at classiccmp.org> Date: Friday, April 1, 2016 at 6:53 PM To: "cctalk at classiccmp.org" <cctalk at classiccmp.org> Subject: AT&T 3B2 floppy format I finally have my own AT&T 3B2/300, and I'm having a heck of a time getting disk images transferred to physical media. I have here a set of AT&T SVR3.2 diskette images, apparently made (not by me) using dd. I would like to transfer them to physical media in such a way that they're usable by the 3B2/300. Here's what I know so far: * 3B2 diskettes are 720KB, Double Sided Quad Density (DSQD) 96tpi * Each side is 80 tracks, 9 sectors per track, 512KB per sector * Sectors use 3:1 interleave * Physical media should be good quality DSDD * The 3B2 fdc is a TMS2797 (WD 2797 compatible) * The 3B2 floppy drive is a CDC 9429 On my PC, I'm using a venerable TEAC FD55-GV with the "I" jumper in place, so at double density it should be spinning at 300RPM. ImageDisk claims that reading and writing at 300kbps is successful. I have been using ImageDisk to translate the BIN files I've downloaded into IMD files with the following commands: D:\> BIN2IMD DISK1.BIN TMP.IMD /2 /U N=80 DM=4 SS=512 SM=1-9 D:\> IMDU TMP.IMD DISK1.IMD IL=3 (The two-step translation is necessary because BIN2IMD cannot directly write 3:1 interleaved data unless it's interleaved in the BIN image, so you have to use IMDU to reshuffle things... it's complicated!) Anyway, after doing this, what I end up with is a disk that is _almost_ usable. I can boot off of it, but it fails shortly after loading the UNIX kernel. I can run the 3B2's "dgmon" floppy diagnostics on it, and they almost pass, but fail to reliably read and write during the R/W test. Now, here's the thing: If I use the exact same media and low level format it _on the 3B2 itself_, the disks are 100% readable on the 3B2 and pass all floppy diagnostics with flying colors. So I'm trying to pin down what about my setup is not right. My pet theory right now is that the R/W gap and Format gap are wrong. The default values for the gaps when calculated by ImageDisk are 24/64. I've played with 22/32, 34/62, and 42/80, all based on reading the datasheet and/or old Linux "fdprm" settings, but nothing seems to make the disks 100% reliable on the 3B2 when written on the PC. Does anyone have any insight into the gap lengths used by the 3B2? Or, have you successfully written 3B2 floppies from disk image before? -Seth -- Seth Morabito