- test-drb@ccmp.vtda.org - classiccmp.org

by khaleeqkg＠yahoo.com

Dear Mc Manis or his Representative We are a small group of student, who were running VAX-3300 Computer System, for our research project. Unfortunately the System has gone out of order. We are in need of VAX-3300 System to retrieve our data archived on TK-70 Tape Cartridge. I have seen your site where from VAX Junks is available. Micro VAX 3300 (Including SCSI Controller, RAM more Than16MB, Hard Disk 1GB nor greater and KFQSA DSSI card worth less than $50. We do not require KFQSA DSSI card. However following Hardware/Software is also required to us: 1. Hard Disk RF-30 and RF-31 2. Controller Card for TK-70 Tape Drive (M7559), 3. Interface Card (M7651) 4. Diagnostic Software on TK-70 Tape Cartridge 5. If you have all or some of these items please inform me about the availability along with their cost. We will arrange the shipping and handling for the items. Your early response would be highly appreciable. Thanking you. Regards Khaleeq khaleeq(a)yahoo.com

23 years, 2 months

1
0
0 0

looking for MFM RLL Drives

by compcyz＠fbx.com

Hello, I have many MFM Drives. Not all tested yet but can. What are they worth. I saw an old st225 just sell on ebay for 20 bucks or so + shipping. Make me an offer or what for trade ect. Oh by the way any body have HDFORMAT.EXE for PCTECH X16B 80186 IBM XT clone motherboard with 5380 SCSI controller built in. Leading to SMS Omti 5400 SCSI to MFM adapter board connected to ST225 5.25 MFM Drive That won't read side 4. Could boot floppy and read Directory to find file names in utility subdir. Need program to low level format MFM on SCSI interface. Bios won't detect modern SCSI drives. Tried emailing one of designers (written on board) now works at micron tech. (evolved name of Co.) But no reply. Cy Van D. in Iowa compcyz(a)fbx.com

23 years, 2 months

1
0
0 0

Please help me ID cards(32)

by fyodonis＠bellsouth.net

Headley: I don't know if you still have this stuff, but I was the engineer who was involved in the design of the MegaScan A33400(ITF-3102) VME Interface. Please let me know if you still have this and if you still need help answering any questions. Regards, Frank [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

HP2000

by glenslick＠hotmail.com

That would be very cool and appreciated if someone put the time into creating such a doc. I have a 2117F and a 2113E that aren't doing much now that I would like to get doing something more interesting at some point. Last fall I saw some scrap HP 1000 systems which I believe had the parts to connect them in a two CPU pair. If I knew more about how to make use of such a configuration I would consider trying to acquire that hardware. >From: "Jay West" <jwest(a)classiccmp.org> > >Perhaps Eric and I (and any other interested parties) should get together >and create a document like "So, you want to run HP TSB?". We could get >definitive answers to exactly what pieces/parts are required, put in some >comparisons between the different versions, etc. Kind of a road map to help >people get these systems running. _________________________________________________________________ The new MSN 8: smart spam protection and 2 months FREE* http://join.msn.com/?page=features/junkmail

23 years, 2 months

4
8
0 0

Assembly on a Apple IIc+

by rhudson＠cnonline.net

What do I need to get started with 6502 Assembly on an apple II? --- I have: 6502 Machine code reference Apple IIc+ Prodos Dos 3.3 --- Things I know I need to know: What call prints a character? What call gets input of some kind (preferably 1 key at a time) Any calls to clear the screen? Any calls to position the cursor? --- Things I know I need to get: Assembler Editor I don't as yet know how to get things from the web to my Apple II, I use a Mac mostly to surf Thanks for the help....

23 years, 2 months

9
20
0 0

Old Computer Companies

by vance＠neurotica.com

I'm trying to think of all the really old computer companies that are still in business. GE and Honeywell no longer make computers. DEC and DG are gone. So there's HP, IBM, Bull... are there any others left from way-back-when? Oh yeah, there's Siemens. And Amdahl's part of Fujitsu now. Do they still count? I guess Fujitsu probably counts on its own merits. Hitachi and Toshiba left the industry recently, after many years. And then there's Unisys, with their recent turn to weird hybrid systems. Did I miss anyone? Peace... Sridhar

23 years, 2 months

27
56
0 0

OT Need parts

by jrice54＠charter.net

I need one of the beige plastic headed screws that secure the side cover on a Dell Dimension case. The is for my UMAX S900 that shares a PaloAlto Design case with the earlier Dell Dimensions. I also need two blank drive filler panels for a HP NetServer LC II. James -- http://webpages.charter.net/jrice54/classiccomp2.html

23 years, 2 months

2
3
0 0

OT Avalanches (was: Columbia)

by julesrichardsonuk＠yahoo.co.uk

>When I was a kid, I tried and tried to make an igloo of packed cubes of >snow. I never could get one finished as once the walls started to curve >I couldn't get the layers to stick long enough to close the thing up and >complete it. An igloo is a very stable structure, but a half-finished >one isn't at all stable... I have a feeling that in survival situations you don't make an igloo, but a tunnel that you lay down in. Dig a trench into the snow first, then you just use a few blocks above surface level to make the roof. Pack snow on top of that to seal the gaps. One end is sealed, then after reversing in you use your pack to seal the entrance up beind you. The other alternative is to dig a tunnel. You make it T-shaped for some reason that currently eludes me; the entrance is at the lowest point of the T and you lay across the 'arms'. Biggest problem if you're sheltering is making sure that someone can find you - using the pack to seal the doorway off goes a long way to achieving that but overnight snowfall could still hinder the rescuers. cheers Jules Everything you'll ever need on one web page >from News and Sport to Email and Music Charts http://uk.my.yahoo.com

23 years, 2 months

6
5
0 0

VAXELN HELP!! needed

by hofmanwb＠worldonline.nl

Hi All, VAXELN is new to me, but I am reasonably at home in the internals of RSX11M, MTS and OS 360. I was called in by the application programmer when he encountered a somewhat deep problem. One or two times a month in the 3rd of three RT1000 running V4.0 of VAXELN the two communications tasks with the microVax 3300 running VMS 5.2 stop. One with access violation, reason mask 05 and one with access violation or with a kernel stack not valid exception. These tasks are identical and each serves its own sorting unit. The VAXELN systems use the DDCMP_V2 module. The systems run continuously. The stop address is for both tasks always in the DAP module (from june 7 1989) at 1FFC from the start It looks as if the FP register contains 0 during the last CLRB -4C4(FP) intruction.I conclude this from the virtual address =FFFFFB3C message.. The system stopped at the same location during startup earlier in the project each time when the 3rd realtime vax was started, but then:maximum links was 32 and maximum circuits was16. This error disappeared when these quantities were doubled to maximum links=64 and maximum circuits=32. The earlier values were ok during the years when only two realtime vaxes were active.and with 2 realtime vaxes these crashes were not noticed. The realtime vaxes all have the remote debugger. The installation is 140 km >from my home. It looks as if register information is hard to get at. Suggestions? Has anyone encountered a similar error? Who has suggestions?. When this gets highly detailed contact off list might be best. Any help will be greatly appreciated! Wim

23 years, 2 months

2
1
0 0

WANTED: RA7x Enclosure/Operator Ctrl. Panel

by jwillis＠arielusa.com

Wanted: RA7x Enclosure/Operator Ctrl. Panel

23 years, 2 months

4
3
0 0

Looking for source of MFM or RLL drives

by CCTalk＠catcorner.org

Yes, the OS allows entering of drive geometry. Actually only supports MFM up to 70Meg. RLL drives will of course work, just not to RLL capacity. I'm looking for the largest drives I can find. From: Ethan Dicks --- Kelly Leavitt <CCTalk(a)catcorner.org> wrote: > Any good sources of MFM or RLL drives. This would be for a Tandy 6000 > running Xenix. > > I'm looking for 70 Meg or higher MFM (110 RLL capacity). Hmm... those aren't so common (in the DEC world, there are two choices - the RD53 (Miniscribe 1325) and the RD54 (Maxtor XT2190). I take it you aren't constrained by a narrow set of expected geometries? (i.e. - you have a running system and/or the install procedure asks you about the drive rather than assuming?) -ethan

23 years, 2 months

3
2
0 0

Burroughs

by moored＠student.charleshays.net

Hi folks , >And, while we're asking, does anyone know what happened to Burroughs? >The Burroughs corporation eventually merged with Sperry Univac and got >absorbed into Unisys > > I've been lurking for a while , have a few old box's about but the ones i'm curious to know the rareity of are 3 Burroughs desktop type units from early 80's they are all 3 different models one newer 85 maybe , I'd have to dig them out and check the model numbers if need be , they all run the "B-20" operating system and booted and ran the last time they were plugged in (one is a smart terminal type ala net boot) . On a couple occasions i've searched all over the net for information and found very little other than the company history stored at the Babbage institute . Are these things as odd as I think they are or has info and availability just managed to elude me ? Thanks for your time Dean.

23 years, 2 months

2
1
0 0

Interesting technique for removing tape discovered

by vcf＠siconic.com

Someone sent me an unassembled Ohio Scientific Superboard II kit in its original box the other day. Unfortunately, they didn't put the original box inside another box before applying tape and the Fedex shipping receipt pouch on the box (over the original OS label). So I had to carefully peel off the various stickies. I was able to do a pretty good job and except for the label tearing due to age, I was able to remove the pouch without damaging it. When I was removing the tape I accidently discovered that if I pulled the tape in a horizontal plane, it actually causes the tape to lift from the box without taking the top layer of the cardboard or any paper labels with it. Grab on to the tape and start pulling on it (hard) rather than peeling it back. It will lift off. The kind of tape I am referring to here is the clear packaging tape. Anyway, something to try the next time someone does this to you. To avoid this, be sure to have your sender put any original boxes inside another box before shipping. I didn't realize this was coming in the original box or else I would have instructed him to do so. -- Sellam Ismail Vintage Computer Festival ------------------------------------------------------------------------------ International Man of Intrigue and Danger http://www.vintage.org * Old computing resources for business and academia at www.VintageTech.com *

23 years, 2 months

4
3
0 0

Old computers from HP, maybe? Anybody know where HP is collecting/storing them?

by RCTech＠cnri.us

HP: Don't trash that old computer By Ian Fried Staff Writer, CNET News.com February 5, 2003, 5:10 PM PT Hewlett-Packard is hoping a little green will help make computer owners recycle more of their old tech gear. The computer maker is testing a program that gives those who recycle their old computers, monitors, printers or other gear a coupon worth up to $50 for any purchase of $60 or more on HP's online store. Under a program announced nearly two years ago, HP charges anywhere from $17 to $31 to recycle products. The company says the coupon will offset the amount customers must pay for the service, which ensures none of the gear ends up in landfills. The need for recycling is growing, particularly as nonprofit agencies become less willing to accept older gear, said Renee St. Denis, manager of HP's recycling effort. The problem of what to do with all this aging equipment has become a major issue facing the tech industry. "Now there is nobody to use it, and (charities) are coming to understand there is a cost to disposing of it properly," St. Denis said in an interview. With the promotion--which runs through April 30--HP hopes to find out whether a financial incentive will boost the number of products being recycled. The company said it already receives thousands of products each year, but would not be more specific on the amount. "We thought we'd give this a shot; then we'll evaluate how to move forward," St. Denis said. Those who return PCs, scanners, handhelds or inkjet printers will receive $20, while those who return monitors and laser printers will receive $30 coupons. A PC with a monitor fetches $50. While most of the products HP gets back are obsolete, the company does keep a list of what some charities are looking for and will donate any gear that meets the charities' minimum standards. "For the most part what we get in here is pretty darn old," St. Denis said. HP's recycling program accepts its gear as well as similar products made by competitors. "We don't want toasters, but we'll take other people's printers," St. Denis said.

23 years, 2 months

5
4
0 0

OT: RE: Collecting, Hacking and the Spooks (was: Gulf War,

by doug_jackson＠citadel.com.au

Wow. That's extremely good news. Unfortunately, my experience in repairing the samsung TV's is that you *start* by replacing about AUS $50 worth of power supply components, then you see what else failed. AARRGGH. Doug Jackson Director, Managed Security Services Citadel Securix +61 (0)2 6290 9011 (Ph) +61 (0)2 6262 6152 (Fax) +61 (0)414 986 878 (Mobile) Web: <www.citadel.com.au> Offices in Melbourne, Sydney, Canberra, Hong Kong, Boston -----Original Message----- From: Philip Pemberton [mailto:philpem@dsl.pipex.com] Sent: Thursday, February 06, 2003 8:49 AM To: cctalk(a)classiccmp.org Subject: Re: OT: RE: Collecting, Hacking and the Spooks (was: Gulf War, Bryan Pope wrote: > And thusly Fred Cisin spake: >>> How much power / heat does a distiller use / generate?! >> How much shine could you make from a still heated by a Pentium? > Oooooh! ooooooh! How bout an ethanol cooling system for a P4?!! The > next 'leet mod! Only one problem with that approach - isn't ethanol, er... highly flammable? i.e. if it gets spilt on the CPU, said CPU goes up in flames along with the methanol cooler and pretty much everything else in the system case... Speaking of naffed up PCs, I was given a Celeron 400 box to play with. The CD ROM was (supposedly) dead. And rattling - uh-oh... Opened up the drive and found out that some in-DUH-vidual put a badly cracked CD in there. The CDROM was a 48x. Can you guess what happened to the CD when the drive got up to speed? That's right. It shattered. I spent 25 minutes picking bits of CD out of the mechanism. And then I powered it up again. And it came up to speed and read a CD fine. Guess that says something about Samsung CD drives then... Unfortunately, the other Samsung 48x drive I was given really was dead - the spindle motor bearings seized up... Later. -- Phil. philpem(a)dsl.pipex.com http://www.philpem.dsl.pipex.com/ CAUTION - The information in this message may be of a privileged or confidential nature intended only for the use of the addressee or someone authorised to receive the addressee's e-mail. If you are not the intended recipient, you are hereby notified that any dissemination, distribution or copying of this e-mail is strictly prohibited. If you have received this email in error please notify postmaster(a)citadel.com.au. Any views expressed in this message are those of the individual sender and may not necessarily reflect the views of Citadel Securix. Feel free to visit the Citadel Securix website! Click below. http://www.citadel.com.au

23 years, 2 months

4
3
0 0

Rookie HP-85 problem

by rhahm＠nycap.rr.com

OK, I took it apart to take alook inside and clean it up. Now I can't get the damn cover back on. It seems to get caught on the tape eject button. Don't want to break the cover forcing it. Are you supposed to separate the monitor/tape brown faceplate from the rest of the cover first? HELP RH

23 years, 2 months

4
3
0 0

Looking for source of MFM or RLL drives

by jwillis＠arielusa.com

I have an RD54 available... no idea whether its working. -----Original Message----- From: Kelly Leavitt Sent: Fri 2/7/2003 6:12 PM To: 'cctalk(a)classiccmp.org ' Cc: Subject: RE: Looking for source of MFM or RLL drives Yes, the OS allows entering of drive geometry. Actually only supports MFM up to 70Meg. RLL drives will of course work, just not to RLL capacity. I'm looking for the largest drives I can find. From: Ethan Dicks --- Kelly Leavitt <CCTalk(a)catcorner.org> wrote: > Any good sources of MFM or RLL drives. This would be for a Tandy 6000 > running Xenix. > > I'm looking for 70 Meg or higher MFM (110 RLL capacity). Hmm... those aren't so common (in the DEC world, there are two choices - the RD53 (Miniscribe 1325) and the RD54 (Maxtor XT2190). I take it you aren't constrained by a narrow set of expected geometries? (i.e. - you have a running system and/or the install procedure asks you about the drive rather than assuming?) -ethan [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

Disk drive head locking (DEC RA-82 and HP 7920)

by jwillis＠arielusa.com

I seem to have only up to RA81, but everything else :( -----Original Message----- From: Dan Veeneman Sent: Fri 2/7/2003 3:04 PM To: cctech(a)classiccmp.org Cc: Subject: Disk drive head locking (DEC RA-82 and HP 7920) Hello, I'm scheduled to pick up a pair of DEC RA-82 drives along with an HP 7920 drive in the next couple of weeks. I don't have any technical documentation for either of these drives, but I'd be very interested in learning the proper procedure for locking down the heads on these drives prior to moving them. If anyone has the steps to take for either or both of these drives, please drop me a note or point me to the proper archive. They've already been warehoused, so it might be too late, but I'd like to be as safe as I can. Thanks! Cheers, Dan www.decodesystems.com/wanted.html [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

WANTED: RA7x Enclosure/Operator Ctrl. Panel

by jwillis＠arielusa.com

New Mexico, USA -----Original Message----- From: Eric Dittman Sent: Fri 2/7/2003 4:46 PM To: cctalk(a)classiccmp.org Cc: Subject: Re: WANTED: RA7x Enclosure/Operator Ctrl. Panel > Wanted: RA7x Enclosure/Operator Ctrl. Panel Where are you located? -- Eric Dittman dittman(a)dittman.net Check out the DEC Enthusiasts Club at http://www.dittman.net/ [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

Old Computer Companies

by fm.arnold＠gmx.net

cctech-request(a)classiccmp.org schrieb am 06.02.2003: ----------<snip>----------- Message: 23 Date: Wed, 5 Feb 2003 12:34:12 +0200 (EET) Subject: Re: Old Computer Companies From: "Jarkko Teppo" <jarkko.teppo(a)er-grp.com> To: cctalk(a)classiccmp.org Reply-To: cctech(a)classiccmp.org Jochen Kunz said: >> On 2003.02.03 03:10 vance(a)neurotica.com wrote: >> >>> > Norsk Data? >>> I'm not familiar with them either. >> I am not very familiar with them. They made some minicomputers in the >> 70'es, mayby some other stuff too. > >I've seen (well, almost) Norsk Data machines in, hmm.. how should I >phrase that: "big controversial power plants where security is quite >important". This was less than ten years ago so I don't think they've >"upgraded" them. Saw a couple of VAXen as well, 4000/90 if I remember >correctly. The VAXes I saw were not in critical roles. > >(I checked, and they've replaced the Norsk Data system: >http://www.tvo.fi/uploads/Outage_Excellence.pdf, works from google cache as >html) > It seems, that Olkiluoto 1 still has the Norsk-data machines. They will change those next year, so they might still keep all that hardware in stock for some time until block 1 is also modernised. If someone likes to save equipment, doc's or photoos, its time to act now... (too far away for me...) BTW, back in the seventies I was working for a large finnish company that build (parts of) the security shutdown system of the Lovisa npp. They also build the npp-operator's training simulator and I remember that it was using several big Eliott computers from UK. What happened to them? I mean Eliott, not N...a Frank Arnold

23 years, 2 months

4
3
0 0

MicroVAX 3800 Power Cable

by pete＠dunnington.u-net.com

On Feb 6, 22:33, Tony Duell wrote: > I don't see how you can do a proper test without a visual inspection of > the connections... And I've yet to see a moulded connector that provides > a proper strain-relief for the cable. A good PAT tester will check at a sensible current (though admittedly a lot only check earth continuity at a proper current). As for strain releif, well you're not supposed to swing the equipment by the power cable, Tony! > > > What is the connector like the normal 'kettle plug' with round pins? > The cable mounted section looks like a normal 'cold condition' _socket_, > but there are 3 round pins sticking out of the face of it (where the > socket holes would be). The chassis part looks like the normal plug > (recessed into the panel, etc) with 3 holes in it in place of the normal > plug pins. I've a feeling I've seen this used somewhere -- but not recently, and I can't think where :-( -- Pete Peter Turnbull Network Manager University of York

23 years, 2 months

2
1
0 0

DEC/PDP documentation received

by jwillis＠arielusa.com

I'll see what I can do. Maybe I can scan them at work. Just found out my UMAX scanner doesn't work under Mac OS X. -----Original Message----- From: pete(a)dunnington.u-net.com Sent: Fri 2/7/2003 3:25 PM To: cctalk(a)classiccmp.org Cc: Subject: Re: DEC/PDP documentation received On Feb 7, 13:39, Zane H. Healy wrote: > Nice haul! > > I'm going to guess that the following would be of definite use to a bunch of > us. What are their age? As far as I know they aren't available: > > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume I: Systems Options > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume II: Module Options A-K > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume III: Module OptionsL-Z PDFs of these would certainly be useful to me :-) -- Pete Peter Turnbull Network Manager University of York [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

DEC/PDP documentation received

by jwillis＠arielusa.com

5th Edition, January 1985 -----Original Message----- From: Zane H. Healy Sent: Fri 2/7/2003 2:39 PM To: cctalk(a)classiccmp.org Cc: Subject: Re: DEC/PDP documentation received Nice haul! I'm going to guess that the following would be of definite use to a bunch of us. What are their age? As far as I know they aren't available: EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume I: Systems Options EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume II: Module Options A-K EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume III: Module OptionsL-Z Of potential interest to a select few (again, I've no idea if they're available): VAXsimPLUS Field Service Manual VAXsimPLUS User Guide RM05 Disk Subsystem Service Manual RM05 Disk Subsystem Student Guide (Digital Internal Use Only) RM03 Disk Drive Maint. Print Set RP04/05/06 Field Maint. Print Set Model 733 DEC Disk Storage Drive Parts Catalog, Jan. 1976 RP04-TC Part II RP04, RP05, RP06 Field Svc. Handbook RP05/RP06 Field Handbook -Company Confidential- RP05/06 677-01/51 Disc Drive Illustrated Parts Catalog Model 677-01/51 RP05/06 DEC DISC MAINTENANCE Guide (Educ. Svcs.) Zane [demime 1.01a removed an attachment of type application/ms-tnef which had a name of winmail.dat]

23 years, 2 months

1
0
0 0

DEC/PDP documentation received

by pete＠dunnington.u-net.com

On Feb 7, 13:39, Zane H. Healy wrote: > Nice haul! > > I'm going to guess that the following would be of definite use to a bunch of > us. What are their age? As far as I know they aren't available: > > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume I: Systems Options > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume II: Module Options A-K > EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume III: Module OptionsL-Z PDFs of these would certainly be useful to me :-) -- Pete Peter Turnbull Network Manager University of York

23 years, 2 months

1
0
0 0

Disk drive head locking (DEC RA-82 and HP 7920)

by dan＠ekoan.com

Hello, I'm scheduled to pick up a pair of DEC RA-82 drives along with an HP 7920 drive in the next couple of weeks. I don't have any technical documentation for either of these drives, but I'd be very interested in learning the proper procedure for locking down the heads on these drives prior to moving them. If anyone has the steps to take for either or both of these drives, please drop me a note or point me to the proper archive. They've already been warehoused, so it might be too late, but I'd like to be as safe as I can. Thanks! Cheers, Dan www.decodesystems.com/wanted.html

23 years, 2 months

1
0
0 0

DEC/PDP documentation received

by healyzh＠aracnet.com

Nice haul! I'm going to guess that the following would be of definite use to a bunch of us. What are their age? As far as I know they aren't available: EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume I: Systems Options EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume II: Module Options A-K EK-LSIFS-SV-005 LSI-11 Systems Service Manual, Volume III: Module OptionsL-Z Of potential interest to a select few (again, I've no idea if they're available): VAXsimPLUS Field Service Manual VAXsimPLUS User Guide RM05 Disk Subsystem Service Manual RM05 Disk Subsystem Student Guide (Digital Internal Use Only) RM03 Disk Drive Maint. Print Set RP04/05/06 Field Maint. Print Set Model 733 DEC Disk Storage Drive Parts Catalog, Jan. 1976 RP04-TC Part II RP04, RP05, RP06 Field Svc. Handbook RP05/RP06 Field Handbook -Company Confidential- RP05/06 677-01/51 Disc Drive Illustrated Parts Catalog Model 677-01/51 RP05/06 DEC DISC MAINTENANCE Guide (Educ. Svcs.) Zane

23 years, 2 months

1
0
0 0

DEC/PDP documentation received

by jwillis＠arielusa.com

I've posted the list on the web... in the process of finishing it and adding the DEC order numbers. http://coherentlogic.dyndns.org/vax/vaxdocs.txt Enjoy!

23 years, 2 months

1
0
0 0

Columbia

by jwillis＠manson.vistech.net

7 people died. 7 people die all the time. These 7 happened to be astronauts. Big deal.

23 years, 2 months

8
9
0 0

Ebay - HP85A

by marvin＠rain.org

There is an HP-86A for sale on ebay at http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3400284610&category=179#… The current bid is $10.50, and it ends at 11:47 PST.

23 years, 2 months

1
0
0 0

Strainge VAXserver 2000 card? (more info)

by Fred.van.Kempen＠microwalt.nl

Indeed, the card I plucked out of the expansion box is only the card with the board's line drivers and faceplate. The real board is inside the machine, and looks to be a regular MV2000/3100 expansion board. Since someone already mentioned that their serial expander has the centronics-like connector for the H3104 on the faceplate, this *must* then be the sync-serial ("X.25") one. See the new pics at: http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-1.JPG http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-2.JPG http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-3.JPG [new] http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-4.JPG [new] These are the 1280x1024 ones., for clarity of the card's details. --fred

23 years, 2 months

2
1
0 0

VAX/PDP docs. received

by Fred.van.Kempen＠microwalt.nl

> Received from a former DEC service rep.: Ohh... my... god ! What's the guy's address? I'll send him a crate of beer as thanks for *not* redirecting his stuff to the garbage truck, as is done WAY too often... yay yay yay! --f

23 years, 2 months

1
0
0 0

OT Avalanches (was: Columbia)

by cb＠mythtech.net

>When I was a kid, I tried and tried to make an igloo of packed cubes of >snow. I never could get one finished as once the walls started to curve >I couldn't get the layers to stick long enough to close the thing up and >complete it. An igloo is a very stable structure, but a half-finished >one isn't at all stable... In boy scouts, we cheated. We used a plastic box to make the packed cubes, and a spray bottle of water to make the blocks stick together. A light misting on the top edge of a block, then press the next block down onto it and hold for a second... igloo superglue! It worked well enough to get the structure finished... alas we didn't make it big enough for all of us in the troop to fit inside (10 of us?), and the pushing and shoving that followed made quick work of tearing it back down. -chris <http://www.mythtech.net>

23 years, 2 months

2
1
0 0

Looking for source of MFM or RLL drives

by CCTalk＠catcorner.org

Any good sources of MFM or RLL drives. This would be for a Tandy 6000 running Xenix. I'm looking for 70 Meg or higher MFM (110 RLL capacity). Thanks, Kelly

23 years, 2 months

3
2
0 0

C= 64's maybe available

by cb＠mythtech.net

Picked this up from the LEM-Swap list, passing it on in case anyone was interested. Reply to him, not me. ---- Subject: [swap] OT; Commodore 64 Date: 2/7/03 8:26 AM Received: 2/7/03 9:25 AM From: Nick Hull, nhull(a)mindspring.com I need to get rid of a pair of Commodore 64 computers. Is there any group that handles these? I hate to just trash things when someone might actually want some. ---- -chris <http://www.mythtech.net>

23 years, 2 months

1
0
0 0

found usefull jumper page

by paulm064＠icqmail.com

Found a pretty good jumper settings page ,has older network adaptors and hard drive data etc. plaese don't swamp it and have it killed!

23 years, 2 months

4
4
0 0

OT: RE: Collecting, Hacking and the Spooks (was: Gulf War, dummie s,

by cb＠mythtech.net

> They restricted the use of HEAT SENSORS but they did not restrict the >police from using estimates of exceesive power usage by the power >companies. That's how they "caught" Zane. The thermal imaging sensors >would have probably shown that the source was a computer and not growing >plants. BTW they also use both technologies for detecking stills built >inside of homes. Does this open up the market to sell used big iron to drug dealers? This way they can justify their extra power usage and heat output. "No officer, I don't grow pot... its just my refridgerator sized computer, pay no attention to the plants behind the curtain" -chris <http://www.mythtech.net>

23 years, 2 months

7
8
0 0

65C51

by jaybp3＠earthlink.net

Just curious... did you find any 65C51 ICs? Jay

23 years, 2 months

2
1
0 0

10Base-FL

by pete＠dunnington.u-net.com

On Feb 6, 23:04, Adrien Farkas wrote: > 10base-FL is 62.5/125. actually, I'm running fddi on 50/125 with no > problems so it shouldn't matter _that_ much what cores you use for it > (besides singlemode 8.5/125, of course). Actually, the standards allow for both 50/125 and 62.5/125 for 10baseFL and FDDI, and everything else up to Gigabit. -- Pete Peter Turnbull Network Manager University of York

23 years, 2 months

1
0
0 0

Something for all you PS/2 fans

by vance＠neurotica.com

Anyone want PS/2 Mod 95's? Apparently some of them have Type-IV (! -- expensive) complexes. Peace... Sridhar

23 years, 2 months

5
9
0 0

10Base-FL

by vance＠neurotica.com

I'm about to put some 10Base-FL in and I was wondering if someone could tell me what kind of fiber I should be looking for? Is it 50/125 MMF like GigE? Or is it 62.5/125 MMF like FDDI? Peace... Sridhar

23 years, 2 months

3
2
0 0

RM Nimbus

by Peter.Hicks＠POGGS.CO.UK

All, I used to have an AX/2 server at home quite a while ago, and all I have left is the hard drive. I want to get this software off the drive, but I threw out my last MFM controller card ages ago. Does anybody have a copy of the old RM NET LM software that ran (runs?) Z-Net networks of PC186 machines? Even better, does anyone have an ISA MFM controller they'd be willing to swap for money? :) eBay hasn't turned up anything :( Best wishes, Peter.

23 years, 2 months

23
43
0 0

IBM 3164 Terminals

by lisa.parmar＠aircanada.ca

Hi Pat, Do you have any of the IBM 3164 terminals left? Lisa [demime 1.01a removed an attachment of type text/x-vcard which had a name of lisa.parmar.vcf]

23 years, 2 months

1
0
0 0

tonights finds

by kenziem＠sympatico.ca

I went thinking I was going to pick up an OT DY4 PPC embedded machine, instead it is an DY4 Orion with dual 8" floppies, the manual, a box of disks and a Volker Craig terminal. A few sun keyboards and a unopened copy of PharLap thrown in for good measure. My wife met me at the door saying this is the last machine, so I'll have to get the stuff from the trunk on the weekend. Does anyone have any tales to tell about the DY4? I'm also looking for drive rails for a SGI Personal Iris.

23 years, 2 months

1
0
0 0

Strainge VAXserver 2000 card?

by Fred.van.Kempen＠microwalt.nl

And thanks to some fucked-up demime thing, pics can be found here: http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-1.JPG http://www.microwalt.nl/Fred/VAXlab/VS2000-OPT-2.JPG These are the 1280x1024 ones., for clarity of the card's details. --fred

23 years, 2 months

5
4
0 0

OT: File compression

by acme＠ao.net

Can anyone suggest a good book on file compression? Or, does anyone know where I can find C source for a simple file compression routine? The program needs to be portable to Linux, MS-DOS, CP/M and CP/M-86. (I am capable of making changes in the code to accomodate different compilers) Of course, there are compression routines which run under each of these OSs, but I need to run the same routine under all four OSs. TIA for any help -- Glen 0/0

23 years, 2 months

2
1
0 0

FS: Acorn System I Microcontroller Kit (Cambridge, UK)

by julesrichardsonuk＠yahoo.co.uk

Seen on cam.misc usenet group (Cambridge, UK) - I have no connection with the seller, so email them directly if interested. cheers Jules ======= From: Alan Bain (afrb2(a)statslab.cam.ac.uk) Subject: FS: Acorn System I Microcontroller Kit Newsgroups: ucam.adverts.forsale.computer, ucam.societies.cucps, cam.misc Date: 2003-02-06 02:58:03 PST ACORN system I 6502 Microcontroller kit as shipped from Acorn in a box full of packing beads. Never assembled, so time to get out your glue can and build it yourself. Kit contains 1 PCB (Issue 3 200000) Dates from 1980 1 Bag of components 1 Bag of ICs (incl SY6502 and the hard to find INS8154D, you were supposed to supply the others yourself -- presumably desoldered from dead boards) and a load of IC sockets. 1 Schematic Diagram I can almost certainly also locate a copy of the construction manual writen from Acorn's Market Square Address, most likely an original! Reasonable Offers (maybe around 40 pounds but no reasonable offer refused)? Alan Bain Everything you'll ever need on one web page >from News and Sport to Email and Music Charts http://uk.my.yahoo.com

23 years, 2 months

1
0
0 0

HP-85 Error 74 stall

by rhahm＠nycap.rr.com

Hi, I am the proud new owner of an HP 85. Printer belts a little ratty but works fine. However when I attempted to Rew/Load/Cat any of the tapes I received with it I got a stall error. I cleaned the capstan which is intact, and did not fall apart, as I understand they tend to do. The tape motor spins fine when I pressed the tape sensor button inside and hit Rew. Finally after a bunch of attempts the tapes began to spin and I could perform the Load, Cat and Ctape operations. I still seem to get fairly frequent stall errors however. Do you think I need to replace the capstan? Can you get them (or the printer belts)anywhere, or should I use the silicon aquarium tube method mentioned in the archives? Any other thoughts appreciated. Eventually hope to hook it up to a floopy drive but need to find a mass storage rom. Also do you know of any good resources on the web for the 80 series as I haven't found a whole lot. Thanks, RH

23 years, 2 months

4
5
0 0

6502 fans - the SBC-2 is about to have another run - order boards now!

by erd_6502＠yahoo.com

(Whoops... let's try that again with the editing *finished* this time... For those who haven't been to http://65c02.tripod.com/ , the SBC-2 is a single-board 6502 with the following onboard: o 1 MHz 65c02 o 32K of static RAM o 32k of EEPROM o 2 x 65C22 Versatile Interface Adapters (VIA) o 1 x 65C51 Asynchronous Interface Adapter. o Eight 16-byte address blocks decoded for I/O (3 used onboard) This will be the second run of boards. At the moment, Daryl has ten orders. The deadline is 15-Feb. Picture at http://65c02.tripod.com/sbc2.jpg Current cost breakdown is: (from Daryl's announcement) $26.20 per board $4-6 shipping US $4-14 shipping outside US $2 for the serial cable (The serial cable is a 10-pin IDC<->DE9M, like the kind you find on Socket3 and Socket7 PeeCee motherboards). No guarantees that more orders will hit a new price point, so if you have an interest in a compact CMOS 6502 SBC, write Daryl: 65c02(a)softcom.net Do it soon. Disclaimer: I have no affiliation with the SBC-2 except as a potential customer. -ethan

23 years, 2 months

2
2
0 0

OT/Admin: tags

by zmerch＠30below.com

Rumor has it that Fred N. van Kempen may have mentioned these words: >Although this has come up a few times already, I am going to bring it >up again. Come kick my butt if you don't like it :) Awrighty -- I got my Size 9.5(US) Lacrosse Icemans on right now... ;-) <thud> Wham. Wham. Wham. Wham. Wham. -- Ascii representation of the sound of a dead horse getting beaten once again... :-( >Given the volume of the list, and the many off-topic (lets not discuss >what is and is not on-topic here) talk, I would like to propose [again] >that we do like other lists do: insert a tag [cctalk] in the Subject: >line of the postings, so it's easy to distinguis the postings from >other, perhaps more pressing e-mail. Not just no... *Hell no*... >Selecting/filtering based on sender address doesn't work well for all >clients, and depends on the ability to use processing rules in the >first place. Then filter on the headers! It's not that hard... =-=-=-=-=-=-=-=-= Received: from ted.kwcorp.com (imail.kwcorp.com [209.83.143.147] (may be forged)) by huey.classiccmp.org (8.11.6/8.11.6) with SMTP id h14Iq2m50008 for <cctalk(a)classiccmp.org>; Tue, 4 Feb 2003 12:52:02 -0600 (CST) (envelope-from jwest(a)classiccmp.org) Received: from jwest [172.16.51.3] by imail.kwcorp.com (SMTPD32-7.12) id AB5BD990224; Tue, 04 Feb 2003 12:50:03 -0600 Message-ID: <005301c2cc7e$32386ee0$033310ac(a)kwcorp.com> X-BeenThere: cctalk(a)classiccmp.org List-Unsubscribe: <http://www.classiccmp.org/mailman/listinfo/cctalk>, <mailto:cctalk-request@classiccmp.org?subject=unsubscribe> List-Id: General Discussion: On-Topic and Off-Topic Posts <cctalk.classiccmp.org> List-Post: <mailto:cctalk@classiccmp.org> List-Help: <mailto:cctalk-request@classiccmp.org?subject=help> List-Subscribe: <http://www.classiccmp.org/mailman/listinfo/cctalk>, <mailto:cctalk-request@classiccmp.org?subject=subscribe> List-Archive: <http://www.classiccmp.org/pipermail/cctalk/> =-=-=-=-=-=-=-=-= These are all unique headers to this list. Any MUA worth its salt can filter on any one of these... even some not worth it, like LookOut Hexpress... >As said, most lists out there already use this technique, it's been >accepted more or less as a standard, so can we *please* use something >like this ? Accepted by whom? All but one of the lists I'm on *don't do this* (not to mention the ones I admin) and the one that did I disliked, and unsubbed as soon as a better list was available... And this is a "standard" just like HTML email is currently a "standard" - it's not even compatible with itself, and in all, it's just a plain bad idea... IMH-But-SysAdmin-Based-O... >I don't want to start Yet Another Discussion, a mere vote would do, as >we're all techies who know what this is about. That sounds like the beginning of a 2-hour-pissing-match I had with my father-in-law a *long* time ago... "I'm not saying this because you don't want to become an auctioneer..." In all fairness, if it were a *user configurable* option, I wouldn't give a whit, so long as I could turn it off... otherwise, you know my vote... but how many times do we have to vote on this, anyway??? Prost, "Merch" -- Roger "Merch" Merchberger -- sysadmin, Iceberg Computers zmerch(a)30below.com What do you do when Life gives you lemons, and you don't *like* lemonade?????????????

23 years, 2 months

2
1
0 0

Columbia

by cb＠mythtech.net

>I do feel for the astronaut's families, and in almost equal measure for the >future of humanity in space. We have *got* to find a better way of getting >in and out of the gravity well. As sick as it seems... these kind of accidents are exactly what brings about the safer ways of doing things. Nearly all safety measures we as society have for everything can be traced back to someone (or many someones) being injured or killed. -chris <http://www.mythtech.net>

23 years, 2 months

20
34
0 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb