- test-drb@ccmp.vtda.org - classiccmp.org

WinSystems LPM/MPM 7109 card? was Re: New Finds Today

by dwight.elvey＠amd.com

Hi Joe The 7109 was made by many manufactures and is a common A/D. It is a dual slope type. Quite accurate when comparing to a reference. It has one funny feature that isn't usually mentioned in the data sheets. If you get an over range, it will transfer some additional energy to the Auto-Zero capacitor. This can take many convertion cycles to recover from. When used with an input mux, make sure that you either have a wait after overrange or some way to clamp it below full scale. Even a single lsb of overscale has significant effect because of the amplification used to do the auto-zero. A single lsb of overscale can be over 100 lsb's on the next read, depending on the A-Z capacitor size. Not good when you are looking to get the most out of the 12 bits. As for the board, maybe just some tracing out will determine the addressing so that you can play with it. I have a 80C188 processor board for the STD with a Forth in Flash on it. I find Forth to be real handy for poking ( and peeking ) at unknown boards such as these. Dwight >From: "Joe R." <rigdonj(a)cfl.rr.com> > > Yesterday I picked up two shoebox sized units that were marked as >"enviromental units". However they had lights marked Tx, Rx, etc and a Comm >port. Inside it had a STD bus chassis with three cards installed. On has a >80C31 CPU, one has a Zilog Z0853004 comm chip and the other has a MAXIM >ICL7109CPL A/D convertor. The first two cards appear to be custom made and >are probably useless for anything except the system they were designed for. >However the third card (with A/D) is a standard commercail product and was >made by WinSystems and is their model LPM/MCM-7109. Does anyone have any >data on this card? It's not on WinSystems website and I tried to contact >them and ask about it but they were less than cooperative. > > Joe >

22 years, 3 months

1
0
0 0

WinSystems LPM/MPM 7109 card? was Re: New Finds Today

by rigdonj＠cfl.rr.com

Yesterday I picked up two shoebox sized units that were marked as "enviromental units". However they had lights marked Tx, Rx, etc and a Comm port. Inside it had a STD bus chassis with three cards installed. On has a 80C31 CPU, one has a Zilog Z0853004 comm chip and the other has a MAXIM ICL7109CPL A/D convertor. The first two cards appear to be custom made and are probably useless for anything except the system they were designed for. However the third card (with A/D) is a standard commercail product and was made by WinSystems and is their model LPM/MCM-7109. Does anyone have any data on this card? It's not on WinSystems website and I tried to contact them and ask about it but they were less than cooperative. Joe

22 years, 3 months

1
0
0 0

New Finds Today

by rigdonj＠cfl.rr.com

Went scrounging today and found a BIG pile of computers. MANY Dell PCs and a lot of IBM Power PCs. Brought home some of the PCs to check out and found that they all have P-III CPUs and ranged from 500 to 866 MHz. Some even had CD-RW drives! More interesting finds included two HP 9836Cs (the color version of the 9836), a HP 9000 380 (Probably top of the line for the HP 9000 200/300 series), a Sun Ultra 1 Creator 3D, a >>Hyundai<< Sparc model HWS-S310 (I had no idea Hyundai built andything like this!), a Matrox Shark 10/100/FX Ethernet switch, a SUN SparcStation 20, a HP drive array with hotswap drives, and one old PC with a very strange looking card in it. I'm going back tomorrow and pulling parts from the PCs that I didn't take. They're all going to a steel scrapper so I'm free to take anything that I want from them. Joe

22 years, 3 months

4
4
0 0

Wire recorders

by HLBebb＠webtv.net

Hello, I found your e-mail when I was searching for wire recorders. I thought perhaps you could help me. I am 85 years old and have some wire tapes of my children and would love to convert them onto cassette or CD. I live in Wsburg , Va. Would you have any contacts of anyone who could help me? Thank you.

22 years, 3 months

1
0
0 0

MS BASIC for a Panasonic HHC RL-H1400

by martinm＠allwest.net

I have accumulated a couple of Panasonic HHC RL-H1400 "Hand Held Computer"s. For a description, see: http://members.cox.net/obsoletetechnology/Panasonic_HHC.html Searching has indicated that a ROM "capsule" containing a version of MicroSoft BASIC was available. Does anyone have one of these capsules, or a dump of a ROM that can be written to a new ROM? The computers that I have came from insurance agents and have insurance software on the ROMs that came with the computers. The insurance ROMs are Motorola MCM 68764C and appear to be UVEPROMs. Thank you, Martin Marshall

22 years, 3 months

5
5
0 0

AUI cables in UK?

by pete＠dunnington.u-net.com

On Mar 5, 8:14, Vintage Computer Festival wrote: > On Fri, 5 Mar 2004, Pete Turnbull wrote: > > The moulded ones, usually beige in colour, a bit thicker than a pencil, > > or somewhat thicker than thinnet cable, are office-grade. [...] > > All the standard-grade ones I've > > ever seen are blue, and about as thick as yellow etherhose. > Ah, thanks for solving the mystery of the weird DA15 cables I got in the > other day. Now I know these are AUI cables. Useful. As Paul pointed out, there were other colours -- they just happen to be very rare here, and I've only ever seen blue ones. However, some of those blue ones weren't PVC, so perhaps they're low smoke/no fume (LSOF). I've also got at least two types of thick ether cable, but both are yellow. And several types of thinnet, including yellow and grey as well as the more common black. As Paul and der Mouse suggested, I agree that it would be worth making up a short flexible AUI cable. Cat 5 is 100-ohm, and ribbon cable is not far off that IIRC; you could use STP instead of UTP to get the shield (some Sun cables are STP), or just ignore it for really a short (a few inches) cable. Or a chunk of old good-quality serial cable should do a good job over short distances, I expect. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

3
2
0 0

AUI cables in UK?

by pete＠dunnington.u-net.com

On Mar 5, 9:37, Paul Koning wrote: > There was some prototype 10Base5 cable that was yellow PE, though. It > had black stripes to mark transceiver spacing. So it got the nickname > "yellowjacket". According to the standard, the markings are supposed to be on all 10base5 cable; they're to indicate where it's safe to put a transceiver, and where to cut the cable at the ends. They're every 2.5 metres, and there should be at least two between transceivers. However, I've seen cable that didn't have the bands, but it was probably ordinary coax rather than intended specifically for ethernet. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

2
1
0 0

Pro-Log M980 PROM Programmer manual

by aek＠spies.com

I'd happy to send the resulting pdf on to Al Kossow for inclusion on his site. -- Is this a different version that what is already there?

22 years, 3 months

1
0
0 0

Pro-Log M980 PROM Programmer manual

by vcf＠siconic.com

Yo Joe! I finally found this. Is this the manual you were needing? Still need a copy/scan? -- Sellam Ismail Vintage Computer Festival ------------------------------------------------------------------------------ International Man of Intrigue and Danger http://www.vintage.org [ Old computing resources for business || Buy/Sell/Trade Vintage Computers ] [ and academia at www.VintageTech.com || at http://marketplace.vintage.org ]

22 years, 3 months

3
4
0 0

classiccmp hard drive issue

by jwest＠classiccmp.org

The Classiccmp server is having some hard drive trouble again. With the 160gb WD drive I put in not too long ago. You may see some blips on the radar screen while I try to copy things off :\ Jay --- [This E-mail scanned for viruses by Declude Virus]

22 years, 3 months

1
0
0 0

TRS-80 Model 12 crt substitution

by pete＠dunnington.u-net.com

On Mar 4, 9:34, Witchy wrote: > > the CRT can hold a charge for a lot longer than 'overnight'. > > Ah, I didn't know that - I thought they discharged naturally..... > > > and it may cause you to drop the CRT. I alwayse discharge a > > CRT with my > > EHT probe before handling it. I'll second that. Not only do CRTs not discharge naturally (unless they're in circuit with a bleed resistor), a disconnected and supposedly-discharged CRT may develop a charge if left alone. The original EHT can force electrons into the glass, and since glass is an excellent insulator, they don't come out again immediately when you discharge the tube. They *may* come to the surface slowly later, and give the CRT a significant charge of opposite to the original polarity. So leave a bleed resistor across a tube you plan to store for a long period (tip given to me by a TV repairman). If you're discharging a recently-used tube, don't use a simple resistor. The EHT on a CRT could be anything from 8kV to several tens of kV in a fancy colour tube, and most common resistors have a breakdown voltage of only 500-1000V. Besides, think about the power dissipation if you discharge a 25kV tube through a 10M resistor: 2.5 milliamps, but 62 watts. Sure, that 62W won't last long, but neither the tube nor your resistor will like it! -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

7
10
0 0

AUI cables in UK?

by pete＠dunnington.u-net.com

On Mar 4, 22:57, meltie wrote: > On Thursday 04 March 2004 22:41, John Honniball wrote: > > meltie wrote: > > > Does anyone in the UK or immediate surrounds have an AUI cable around > > > that they'd be willing to part with for a small amount of beer tokens? > > > > I can do you an AUI cable, but it'd be a "normal", non-right-angle one. > > Let me know if that'd be OK. Send clearance dimensions if you can! > > After a quick look, it's around 4.2 - 4.3 cm...Is it doable? There's no way a standard-grade blue AUI cable will turn through 90 in less than 15 cm. It might just be doable with an office-grade cable. They tend to be thinner and more flexible than the proper thick blue ones. Or you could remove the cover and fit a right-angle cover, probably. You could certainly do that with an office-grade cable -- I used to have one like that. I seem to remember having a genuine DEC beige transceiver, about twice the size of the minature Allied Telesyn ones that are so common, which had the AUI connector on the side instead of the end. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

5
6
0 0

Queries to group

by dwight.elvey＠amd.com

Hi Ok, this is just too much of a coincidence. We just got 5 post that were queries about post to our group. Only one of the post recognized that they were sending to a group. I find it hard to believe that these are simple people looking for information ( all at the same time ). I sure wish I knew what they were up to or maybe it is the end result of some virus. I just doesn't make any sense. See: Heathkit ES-400 atc-510 simulator Texas Instuments TIL-306 Old Tandy Computer Equipment Hi, Hp logic analyzer What are they up to. Are these really valid queries?? Dwight

22 years, 3 months

3
2
0 0

Texas Instuments TIL-306

by electronicrepair＠teamsesco.com

Hi, My name is Miller Miller and I was looking for some TIL-306 Displays and I came across your forum. You mentioned that you knew a supplier that might have some surplus of these. Does he still have them? Can you tell me who it is. Thanks for any help that can provide. Mike Miller

22 years, 3 months

2
1
0 0

PDP-8/A board info

by ggs＠shiresoft.com

Hi, I'm trying to figure out what this board is/does. It's a DEC hex height board marked M8597A. On the back it's also marked PDP 8A Control. Anyone have any ideas? Thanks. -- TTFN - Guy

22 years, 3 months

3
2
0 0

Hi, Hp logic analyzer

by gwenael.godde＠wanadoo.fr

Hi, I saw your message at http://www.classiccmp.org/pipermail/cctech/2003-May/014475.html I have a 1650b model but without any system disk. (The system disk is needed to use the monster) And i wasn't able to found any file on the www. If you have the system disk, is it possible for you to send it to me (by email)? Many many; Thanks Gw?nael GODDE

22 years, 3 months

1
0
0 0

The story finally make the paper.

by kenziem＠sympatico.ca

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Late last fall I asked about talking to the press, the story appeared today. http://www.canada.com/ottawa/ottawacitizen/news/story.html?id=b5e1276c-930e… The pictures seem to be missing to non subscribers/or online front page: Metal rack with nabu box, VAX monitor, wall in background with ps2 rs6000 :Lisa inside: wall shot apples and clones : NeXT cube - -- Ottawa, Canada Collector of vintage computers http://www.ncf.ca/~ba600 -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.2 (GNU/Linux) iD8DBQFARztPLPrIaE/xBZARAg0zAJ9WL4k1/Y5pfb9iJIcvd1f86oJV8QCfZ0QR MUEgoA4Y8RH0DzqtTQQH8+Y= =IZKu -----END PGP SIGNATURE-----

22 years, 3 months

7
9
0 0

AUI cables in UK?

by pete＠dunnington.u-net.com

On Mar 5, 0:52, Witchy wrote: > Blue? I've never seen a blue AUI cable! Then again I only worked with > moulded DEC ones so I dunno about 3rd party products :) The moulded ones, usually beige in colour, a bit thicker than a pencil, or somewhat thicker than thinnet cable, are office-grade. They have much higher losses and you can't use them for long runs. I think the maximum allowed length is about 30'. All the standard-grade ones I've ever seen are blue, and about as thick as yellow etherhose. Maximum length 164' (50m). -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

2
1
0 0

RL02

by technobug＠comcast.net

One of the local junkers has a RL02 on the line to be parted. If anyone is interested I'll be around there later today and can ask for a price and a reprieve. Claude

22 years, 3 months

2
1
0 0

(no subject)

by terryf＠intersurf.com

Hello; I have been a member of this group for several years, although not really contributing anything to it. Now, here's my chance, take a look at www.ccompforum.com and tell me what you think. Its free, belongs to me, and is offered as an addition to the resources of this group, for this group. For you test-based folks, it has full email->forum and forum->email capabilities. Thanks for looking Terry Freeman terryf(a)cox.net terryf(a)intersurf.com

22 years, 3 months

6
6
0 0

H744 +5 supply - easy to fix?

by GOOI＠oce.nl

Aha, again one scan I did to make somebody happy :-) I realize that the directory path and file names should be "a bit" shorter though ... I have sent Jay West 7 or so CD-ROMs with scans of FMPS and manuals last february (2003!). That's a lot more than on mainecoon (only 4 CD-ROMs). If Jay is reading this: how's the PDF step getting along? In the mean time I have filled up an other CD with manuals. - Henk, PA8PDP. > -----Original Message----- > From: Tom Uban [mailto:uban@ubanproductions.com] > Sent: donderdag 4 maart 2004 16:50 > To: General Discussion: On-Topic and Off-Topic Posts > Subject: Re: H744 +5 supply - easy to fix? > > > > >I could not find a schematic - do you have one? (I realize > it's a straight > >forward switcher, but I like a picture :-) > > Here's a scan from the 11/45 engineering drawings which > includes the H744: > > <http://www.mainecoon.com/classiccmp/PDP-11-45/PDP-11-45%20sys > tem%20ED%20(H744-45-46-54%20&%20G772)%20part-g.tif>http://www. > mainecoon.com/classiccmp/PDP-11-45/PDP-11-45%20system%20ED%20( > H744-45-46-54%20&%20G772)%20part-g.tif > > > --tom >

22 years, 3 months

1
0
0 0

MIL-STD-1397C ???? was Re: New Finds Today

by rigdonj＠cfl.rr.com

At 09:06 PM 3/4/04 +0000, I wrote: > >> Went scrounging today and found a BIG pile of computers. MANY Dell PCs >> and a lot of IBM Power PCs. Brought home some of the PCs to check out and >> found that they all have P-III CPUs and ranged from 500 to 866 MHz. Some >> even had CD-RW drives! More interesting finds included two HP 9836Cs (the >> color version of the 9836), a HP 9000 380 (Probably top of the line for the >> HP 9000 200/300 series), a Sun Ultra 1 Creator 3D, a >>Hyundai<< Sparc >> model HWS-S310 (I had no idea Hyundai built andything like this!), a Matrox >> Shark 10/100/FX Ethernet switch, a SUN SparcStation 20, a HP drive array >> with hotswap drives, and one old PC with a very strange looking card in it. I just checked out the weird card that was in the old PC. It's a MIL-STD-1397C communications interface. Here's a link to a site about the card (a Navigator II). <http://www.sabtech.com/productlist.aspx?str=27> I've never heard of this MIL STD before is anyone familar with it? Joe

22 years, 3 months

3
5
0 0

TRS-80 Model 12 crt substitution

by redodd＠comcast.net

Hello, I broke the neck off the crt in my TRS-80 Model 12. I have a crt from a Model 4. Can I use this in the Model 12 or will it cause problems like smoke etc.? Thanks. Ralph

22 years, 3 months

9
15
0 0

absurd.org

by vcf＠siconic.com

-- Sellam Ismail Vintage Computer Festival ------------------------------------------------------------------------------ International Man of Intrigue and Danger http://www.vintage.org [ Old computing resources for business || Buy/Sell/Trade Vintage Computers ] [ and academia at www.VintageTech.com || at http://marketplace.vintage.org ]

22 years, 3 months

1
0
0 0

weird find: papertape "patch" puncher

by sloboyko＠yahoo.com

www.westnc.com has these patches. I've been thinking about getting some - but the tool is fairly expensive for hobby purposes. And on that subject, wow, is mylar tape getting expensive! ===== -Steve Loboyko Incredible wisdom actually found in a commerical fortune cookie: "When small men cast long shadows, then it is very late in the day." Website: http://juliepalooza.8m.com/sl __________________________________ Do you Yahoo!? Yahoo! Search - Find what you’re looking for faster http://search.yahoo.com

22 years, 3 months

2
1
0 0

New Finds

by marvin＠rain.org

As quite a few people are aware, I tend to *really* like documentation and books. Today was a good day for that as I acquired part of the library from someone who had died a few years ago and was into computers. The computer related books ranged from the 50's to the early 80's. A couple of books I had not seen but look to be very interesting are: The Computer from Pascal to von Neumann - Goldstine The Analytical Engine - Bernstein Sequential Machine: Selected Papers - Moore There were quite a few books on software design, digital hardware design, analog and hybrid computer design, compter logical design, operating systems (including Tanenbaum), etc. This is enough to keep me busy for a while checking them out :). Unfortunately, an H-89 had already been recycled but there is still the possibility that the manuals, etc. are still around. After I cull out the books I want, I'll list them on the Computer Marketplace.

22 years, 3 months

1
0
0 0

H744 +5 supply - easy to fix?

by brad＠heeltoe.com

I finally got my TS11 racked this morning and after a good cleaning found that it has no +5v. (I must say, I love DEC manuals...) Looks like the H744 supply is not working. Anyone know about these? Are they easy to fix? Should I just pull it, find a schematic and start probing? (anyone have one they want to part with? :-) thanks! -brad

22 years, 3 months

4
5
0 0

H744 +5 supply - easy to fix?

by GOOI＠oce.nl

Hello Paul, just to enable all readers to understand I'll answer in English. The "RCD" (say Dutch Radio Control Service) has changed their policy since Sept, 1st, 2003. You can get -if still available- within some restrictions (depends on the license) the call you like (for $$$). I had the C license, and wanted to "upgrade" from PE1CKF to PE1PDP, but I was studying for the morse exam. I passed the very last morse code exam last December, and changed the prefix also to reflect the A license that I now hold. For insiders: I hope to be QRV on HF in a few months, and what that makes special is that I use equipment from RACAL, no Japanese toys! What is RACAL? Check my home page on www.pdp-11.nl and on the opening page at the bottom right, click on the animated gear box ... 73, - Henk, PA8PDP. > -----Original Message----- > From: Paul Koning [mailto:pkoning@equallogic.com] > Sent: donderdag 4 maart 2004 15:10 > To: cctalk(a)classiccmp.org > Subject: RE: H744 +5 supply - easy to fix? > > > >>>>> "Gooijen" == Gooijen H <Gooijen> writes: > > Gooijen> success with your repairs, - Henk, PA8PDP > > Aardige roepletters! Ik wist niet dat de RCD tegenwoordig roepletters > op verzoek leverde. > > paul, ni1d, ex-pa0pkg

22 years, 3 months

3
2
0 0

8Kx8 EPROMs -- was Re: MS BASIC for a Panasonic HHC RL-H1400

by pete＠dunnington.u-net.com

On Mar 4, 14:52, John Allain wrote: [ about Motorola MCM68764 EPROMs ] > > Fancy parting with a few? They're 24-pin 8Kx8, which makes > > them particularly useful for some DEC boot ROMs > > Spit out some part numbers for compatible EPROMs and > I'll check my cache of pulls for you. Thank you. Trouble is, I don't know of any equivalent EPROMs, except the Motorola MCM68766 and SCM90448 ;-) All the other 8Kx8 EPROMs I know are 28-pin. While I remember, does anyone know what DEC ROMs 23-398E4 and 23-399E4 are? They're in Motorola SCM90448Cs, which is what reminded me. I can't remember what they came out of; possibly a PDT. Anyone know about 23-126E4 and 23-127E4 (mask ROMs)? Does anyone have any KDF11-B or KDJ11-B boot ROMs I could add to my collecton? -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

1
0
0 0

MS BASIC for a Panasonic HHC RL-H1400

by pete＠dunnington.u-net.com

On Mar 4, 10:53, Roger Merchberger wrote: > > > > The insurance ROMs are Motorola MCM 68764C and appear to be UVEPROMs. > > > > > > You and the rest of the HHC community. I've got an HHC myself, and all > > > mine has are the insurance EPROMs, too. > > I actually have about 20 *pounds* of these eproms... Fancy parting with a few? They're 24-pin 8Kx8, which makes them particularly useful for some DEC boot ROMs (which is the only place I've seen them before). They fit *my* programmer :-) -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

3
2
0 0

H744 +5 supply - easy to fix?

by pete＠dunnington.u-net.com

On Mar 4, 7:44, Tom Uban wrote: > I've seen a number of the rectifiers fail, so I would concur that it > is a common component to fail. Also, those supplies have always > whistled, even when new from the factory. Well, I've seen a few that don't whistle, and I don't really think they should; the coil laminations are supposed to be glued together and encapsulated. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

2
1
0 0

TRS-80 Model 12 crt substitution - Now I need help with 8" drives

by redodd＠comcast.net

Thanks to all who replied to the crt problem. The crt from the TRS-80 Model 4 was a perfect replacement for the Model 12. Now I have 2 - 8" Tandon thinline TM848E dsdd drives that have problems (in the Model 12). Drive 0 (lets call it A) used to work fine but now all it does is blink (the red busy led). 3 blinks followed by 1 blink or maybe it's 1 blink followed by 3 blinks, hard to tell. Drive 1 (call it B) always made noise and wasn't as reliable as A. I took A out, made B drive 0 and installed the resistor pack. Now B won't boot, I get to "initializing" and then I get a seek error. I have an original TRSDOS 2.0b disk and a copy and both used to work. Both get the same error. The drives have what I am going to call a logic board that's easy to remove. It has the drive and power connectors on it. I've tried every combination of mixing drives and logic boards but I still get the same errors. Does this blinking make sense to anyone and can I cure the seek errors on the other drive? Thanks again for listening to my ranting. Ralph

22 years, 3 months

1
0
0 0

H744 +5 supply - easy to fix?

by GOOI＠oce.nl

Just my 2c. I repaired 2 H744's up till now. They are indeed an easy piece to work on. One had a defective rectifier bridge (the 1 x 1 inch square block with 4 terminals) and the other was more peculiar: one big electrolitic capacitor (AFAICR it is connected directly to the PCB, fixed with screws) made a short circuit between the housing of the capacitor and a trace on the board. The plastic insulation of the capacitor some how was that bad to allow the short circuit ...! success with your repairs, - Henk, PA8PDP > -----Original Message----- > From: Brad Parker [mailto:brad@heeltoe.com] > Sent: woensdag 3 maart 2004 22:39 > To: General Discussion: On-Topic and Off-Topic Posts > Subject: H744 +5 supply - easy to fix? > > > I finally got my TS11 racked this morning and after a good cleaning > found that it has no +5v. (I must say, I love DEC manuals...) > > Looks like the H744 supply is not working. Anyone know about these? > Are they easy to fix? Should I just pull it, find a schematic and > start probing? > > (anyone have one they want to part with? :-) > > thanks! > > -brad

22 years, 3 months

2
1
0 0

H744 +5 supply - easy to fix?

by pete＠dunnington.u-net.com

On Mar 4, 8:22, Gooijen H wrote: > I repaired 2 H744's up till now. > They are indeed an easy piece to work on. > One had a defective rectifier bridge (the 1 x 1 inch square > block with 4 terminals) and the other was more peculiar: > one big electrolitic capacitor (AFAICR it is connected > directly to the PCB, fixed with screws) made a short circuit > between the housing of the capacitor and a trace on the > board. The plastic insulation of the capacitor some how was > that bad to allow the short circuit ...! Hmmm... one of mine had a faulty rectifier too. Not hard to diagnose or replace, but I wonder if that's a common failure? Another one had a bad filter cap -- but it had died of age (leaked) rather than causing a short. Another common "problem" seems to be whistling from the coil, if it's begun to delaminate. Probably a sign of previously running hot, and not necessarily anything to worry about. Several of my "brick" PSUs had faulty bulbs, and I found the easiest way to fix that ws to replace the bulb with an LED and a resistor, as found on the later versions. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

2
1
0 0

86/330 Problem(s)

by hirschopd＠msn.com

Joe, We solved the hardware portion of our problem and are now trying to resolve some iRMX system issues. How do I get availability and price on some of the Intel Manuels included in your list and that of Alossow's. Paul Hirsch >From: "Joe R." <rigdonj(a)cfl.rr.com> >Reply-To: "General Discussion: On-Topic and Off-Topic >Posts"<cctalk(a)classiccmp.org> >To: "General Discussion: On-Topic and Off-Topic Posts" ><cctalk(a)classiccmp.org> >Subject: Re: 86/330 Problem(s) >Date: Sat, 28 Feb 2004 12:27:28 -0500 > >At 02:27 AM 2/28/04 +0000, you wrote: > >Joe, > >do you have part numbers on the booards you have? > >Paul Hirsch > > > Here is a link to a Multibus webpage that I've been working on. ><http://www.classiccmp.org/hp/multibus/multibus.html>. MOST of the cards >that I have are listed there along with descriptions, part numbers and >pictures. It's still a work in progress so there are some missing bits and >pieces and I still have a stack of cards to add to it. It seems like >everytime I turn over a rock around here I find more Multibus stuff :-) > > FWIW I gutted* four Intel 86/330s a couple of years ago so I have all >the >cards for them. > > *Before anyone complains about me gutting vintage systems I'd like to >point out that these had had the hard drives removed before I got them and >I didn't have any Sw or docs for them and that I spent several months >trying to track down the stuff before I gave up and stripped them. I posted >several requests on this list and didn't get a single reply. > > Joe > > > > > > > >>From: "Joe R." <rigdonj(a)cfl.rr.com> > >>Reply-To: "General Discussion: On-Topic and Off-Topic > >>Posts"<cctalk(a)classiccmp.org> > >>To: "General Discussion: On-Topic and Off-Topic Posts" > >><cctalk(a)classiccmp.org> > >>Subject: Re: 86/330 Problem(s) > >>Date: Fri, 27 Feb 2004 18:17:09 -0500 > >> > >>At 02:28 PM 2/27/04 -0800, you wrote: > >> >On Fri, 27 Feb 2004, Paul Hirsch wrote: > >> > > >> >> We have an 86/330 that will not boot. We are using the RMX 5.1 > >>Operating > >> >> System. Following power on we compete the SCT Test and begin >booting > >>and > >> >> get a "Divide overflow occured". We have replaced the 8086 >procrsser, > >>the > >> >> 8087 coprocessor and the memory boards. At this point we are out of > >>options > >> >> unless it is the cpu board (144548-003 Rev C). 1) if any one has >any > >>advice > >> >> I would appreciate it, or if anyone has a board or computer that >they > >>would > >> >> like to sell. > >> > > >> >Sounds like a software problem. > >> > > >> >What's an 86/330? > >> > >> Sounds like an Intel 86/330 computer (8086 CPU Multibus system). I >have > >>parts for them and I've already replied to him. > >> > >> Joe > >> > >> > > >> >-- > >> > > >> >Sellam Ismail Vintage Computer > >>Festival > >> > >--------------------------------------------------------------------------- > >>--- > >> >International Man of Intrigue and Danger > >>http://www.vintage.org > >> > > >> >[ Old computing resources for business || Buy/Sell/Trade Vintage > >>Computers > >> ] > >> >[ and academia at www.VintageTech.com || at > >>http://marketplace.vintage.org ] > >> > > >> > > > > >_________________________________________________________________ > >Watch high-quality video with fast playback at MSN Video. Free! > >http://click.atdmt.com/AVE/go/onm00200365ave/direct/01/ > > > > _________________________________________________________________ Fast. Reliable. Get MSN 9 Dial-up - 3 months for the price of 1! (Limited-time Offer) http://click.atdmt.com/AVE/go/onm00200361ave/direct/01/

22 years, 3 months

2
1
0 0

Elektor and OSI's OS-65D (was OHIO-DOS)

by RMaxwell＠atlantissi.com

As the owner of a modified and still-working OSI Superboard 2 running under OS-65D 3.3, I may have a few insights about the Elektor link to OS-65D: - I had owned my machine for around 5 years (that would make it 1985) when a friend showed me the two-part Elektor article of a floppy-disk interface for the ongoing "Junior Computer" series. Using the schematics, I hand-wired (anyone else remember Vector's "Pencil Wiring" with solder-through insulation?) a disk interface for my Superboard. - The Elektor article "adopted" OS-65D because OSI sold the DOS as a stand-alone product, complete with utilities for customizing disks, developing code in BASIC and Assembler, and capable of running serial or memory-mapped user I/O with the change of a byte in DOS. It sounds like the Elektor authors went forward and used OD-65D for later projects. - By 1985, MA/COM had renamed OSI to ISOTRON during the slow- and shut-down of manufacturing - they stopped buying masked ROMs, and made Superboards and C1Ps patched to use 2716 EPROMs instead - but were still selling the Disk OS. When I telephone-ordered a copy and asked for "OS-65D V. 3.3 for a C1P", a fellow worker figured I was some sort of spy speaking code! Fortunately, the folks at the factory knew what I was talking about. The documentation binder bears the name ISOTRON on its cover. - Like the Elektor authors, I patched my OS-65D, for an 80x24 video card in my system. I had written extensions into a copy of the OSI Monitor ROM: I was a little peeved when OS-65D loaded, ignored the redirected video, and brought in its own drivers for the original 24x24 screen... I was sooo glad I maintained back-compatibility. I still have the original OSI disks and docs: there are 5 disks with all sorts of utilities (mostly in BASIC), the binder for the OS and separate manuals for the "Assembler/Editor and Extended Monitor" and disk BASIC. The handiest thing (and most well-worn!) is the little fold-out card listing DOS commands, memory locations and error code descriptions. I'm a little puzzled at the reference to OS-65D V3.2... Version 3.3 was the "full" version, and the single-floppy reduced version was 3.1: perhaps someone patched a version 3.1 disk for their own project, and just incremented the number? Bob Maxwell --- Original Message --- > > I'm looking for information on the OHIO-DOS system. > > Has anyone some sources, programs or historic info > > on this OS for the 6502? > > > > Right now I'm rebuilding an 65816 system (EC65K) which > > was published in 1986 by Elektuur/Elektor and was running > > OHIO DOS 65D V3.2. > > Ohio Scientific Instruments (OSI) had a 6502 OS in the late > 1970's and early 1980's called OS-65D. They were bought by > MA/COM (sometimes mistyped as MA-COM) who carried on for a > couple of years. I don't know whether they licensed it to > any other vendors, but you might Google for OS-65D. Also, > OS-65U was their multi user OS. I'm a "fan" of OSI, if it > turns out that this is the OSI OS, I would be interested to > know the story of Elektuur/Elektor and how the old (and to > be honest, rather crude) OS was being used in 1986. > > Bill Sudbrink >

22 years, 3 months

6
5
0 0

CPT 8520

by jduck＠earthlink.net

Hi, I have a CPT 8520, printer and keyboard but I can't find the power cord or printer cable. Could you provide any info on finding CPT hook ups? Thanks, Jack Duckworth

22 years, 3 months

3
2
0 0

Brother Wordprocessor Floppy Disks

by tlindner＠ix.netcom.com

Yesterday my boss came to me and handed me a stack of 3 1/2 inch floppy disks and asked me to get the data off them. Ahh, the perils of being the geekiest person in your orginazation! :) Anyway, all he could tell me is that they were from a Brother word processor. It didn't have a model number and no serial port. One of the disks is a system disk ("Spreadsheet, punctualtion alert and data storage disk for Brother Word Processor version <1.0>") and is dated 1991. I tried the disk in my DOS 6.22 PC, no deal. Then I tried cw2dmk (thanks Tim!) and my Catweasel, but I guess the format isn't close enough to IBM 370 (FM) or IBM 34 (MFM) formats to be useful. Does anyone know of a tool I can use to read these disks? Barring that: does anybody know what format the disk is using? I'm not past modifying cw2dmk to read it, but I would hope not to have to reverse engineer the "on disk" format. Thanks! -- tim lindner tlindner(a)ix.netcom.com

22 years, 3 months

2
1
0 0

H744 +5 supply - easy to fix?

by pete＠dunnington.u-net.com

On Mar 3, 16:38, Brad Parker wrote: > > I finally got my TS11 racked this morning and after a good cleaning > found that it has no +5v. (I must say, I love DEC manuals...) > > Looks like the H744 supply is not working. Anyone know about these? > Are they easy to fix? Should I just pull it, find a schematic and start > probing? It's used in various devices, from KL10s to 11/34s so the schematic shouldn't be hard to find, and yes, they're fairly easy to work on. It's a fairly simple circuit based on a 723 regulator chip. I think I do have a spare, but I doubt if you want to pay transatlantic shipping :-) H7440 and H7441 are very similar (different circuits, same purpose). -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

1
0
0 0

Hokki =)

by pete＠dunnington.u-net.com

On Mar 3, 12:01, Jules Richardson wrote: > On Wed, 2004-03-03 at 04:18, pete(a)dunnington.u-net.com wrote: > > Looking forward for a response :P > > Now you're going to have to tell us idiots (i.e. me) what Hokki is... It's a virus (or at least that subject line was created by a virus), and it DIDN'T come from me. -- Pete Peter Turnbull Network Manager University of York

22 years, 3 months

3
3
0 0

atc-510 simulator

by mwallin＠cinci.rr.com

Doug- hello, not to be a pest, but I was about to list some accessories for my old atc-510 flight simulator on ebay. I searched the internet for atc-510 simulator, and only came up with a handful of results. One of them was a thread where you said you were looking for something for your 510. Please let me know 1) if you still have the unit and 2) if you are looking for any accessories. thanks for your time and sorry to bother you, Mike

22 years, 3 months

1
0
0 0

Saved (big haul)

by waltje＠pdp11.nl

Hi all, Thanks to Andreas Holz and Mr. Howard Israel of Zetters Pools Ltd in London, we managed to save three PDP-11/94's, two 11/44's and a /24, plus RL02 disks, a zillion spares, a lot of documentation and small stuff. All systems were SCSI based, so, yes, we're VERY happy with them! Cheers, Fred -- Fred N. van Kempen, DEC (Digital Equipment Corporation) Collector/Archivist Visit the VAXlab Project at http://VAXlab.pdp11.nl/ Visit the Archives at http://www.pdp11.nl/ Email: waltje(a)pdp11.nl BUSSUM, THE NETHERLANDS / Mountain View, CA, USA

22 years, 3 months

1
0
0 0

Strange Old Disk

by aek＠spies.com

It is either for a CDC Hawk (9427) or Phoenix (9448) I don't have a picture of either drive handy though to tell.

22 years, 3 months

1
0
0 0

Anyone near Salem, Ohio?

by tony.eros＠machm.org

I may have a line on some vintage equipment in Salem, Ohio, near Youngstown. Is there anyone on the list living nearby who might be willing to help with pickup, packing and shipping? I'd happily pay shipping/packaging costs plus a little something for your trouble. -- Tony

22 years, 3 months

2
1
0 0

Hokki =)

by pete＠dunnington.u-net.com

Looking forward for a response :P password: 15135

22 years, 3 months

4
3
0 0

Heathkit ES-400

by penson＠email.arizona.edu

Good morning. I came upon your email address while doing a google search for information on the Heathkit ES-400. You had posted an inquiry asking if anyone knew how many ES-400s had been made or sold. Wondering what you found out? An ES-400 recently turned up at a museum in Minneapolis. Cheers, Chuck Penson University of Arizona

22 years, 3 months

1
0
0 0

Vax Tapes Give Away

by edelen＠sierra1.nrl.navy.mil

Do you still have those Vax tapes? If so I'd love to get them from you. Keech Edelen IT Specialist III 202-767-4244 office 877-428-8780 pager 240-346-6829 cell

22 years, 3 months

1
0
0 0

Apple IIc

by lyosnorezel＠yahoo.com

Hey ya'll I just located an old Apple IIc and was trying to figure out it's power supply... anyone know where I can find pinouts for this computer's power supply port? It's the male side of a 7 pin plug. Thanks. Lyos Gemini Norezel P.S.- I'll be getting a Commodore 64 (fully loaded/equipped) and a TRS(trash)-80 in the next coupla days... oh boy, oh boy!!!!!!!!!!!!! I love getting "new" toys. --------------------------------- Do you Yahoo!? Get better spam protection with Yahoo! Mail

22 years, 3 months

5
5
0 0

Linux Box + DOS 3.2 box + (1)5.25 floppy drive (okidata 3305BU) = HELP!!!!!!!!

by lyosnorezel＠yahoo.com

Hey y'all... I need some help. I recently acquired a Compaq Portable(ye right... at 35LBS no one is crazy enough to carry this machine around) II... with a hard drive and a 5.25 floppy disk drive. The hard drive apparently has MSDOS 3.2 and some Novell application. When booted up it first checks the memory then it checks active partions... then it starts going in some kinda loop looking for a file server that isn't there. I don't have any other 5.25 floppy drives so I am unable to create disks to transfer files to this box. I was wondering if it was possible to connect the floppy drive to my linux box and copy the files to the disk(s) from there and retransfer the drive to the compaq to use. Problem is that the Linux box is an RH9 platform on a PII (686) system. Would RH9 even have the needed drivers for a drive this ancient? Can this be done or am I, for all intensive purposes, screwed? Lyos Gemini Norezel --------------------------------- Do you Yahoo!? Get better spam protection with Yahoo! Mail

22 years, 3 months

12
15
0 0

[OT] Strange/Help

by patrick＠evocative.com

Is anyone able to open http://java.sun.com/?

22 years, 3 months

8
9
0 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb