test-drb

test-drb@ccmp.vtda.org

101090 discussions

by mythtech＠mac.com

>I've never heard these called "video dongles", and while they don't >come in the package with the 6100 DOS board, the manual says it's >needed, shows its picture, and says it comes with the computer in >which you're trying to install the board. Well.. there are two different video "adaptors" that were being refered to in that thread. One is the HDI-45 to RGB adaptor, that came with all the "AV" powermacs that had the AV video port. I think that was limited to the 6100, 7100, 8100 series (but may have included others). This was needed to connect a standard RGB monitor to the HDI-45 AV video connector. Or, Apple prefered you bought an AV monitor that plugged directly into the port and provided video, audio, ADB, and for some reason I think color calibration (but I might be wrong on the last one). The other "adaptor" or dongle that was being refered to, is the Video Loopback connector for the DOS cards. The two DOS card styles I have (the "Houdini" from the Q610, and the later PC Compatability cards for the PCI Powermacs), required a video cable that plugged from the DB-26 port on the DOS card, looped into the RGB port on the Mac, and had an output for RGB. It enabled you to use one monitor for both DOS and Mac, or if you don't connect the loop to the Mac's RGB, you could use two monitors, one for each world. Also, the Q610 version provided a Joystick/Game/Midi port. That port was not on the cable for the PCI version, as the Game/Midi port was right on the DOS card. The question that seems to have come up is, does the 6100 DOS card have that loopback connector at all? The PCI DOS cards can either use the the external loop connector... OR an internal connector for Macs that support it (you need the GIMO slot, which many of the PCI Powermacs had). There is a possibility the 6100 card does something similar. But, if the 6100 DOS card needs the cable, is most definitly should have come with it. The Q610 came with it, and the PCI cards came with both the internal AND external cables as far as I am aware (I have never bought a PCI one new... two of mine came installed in a 4400 from Apple, and included the external, but not internal cable, and my 3rd came installed in a used 7200 with an internal, but not external... but the eBay ads I have seen for boxed ones, always say they have both internal and external cables, and since you need one or the other cable, and Apple had no way of knowing which PCI Powermac you planned to use it with, it would have made sense to include both styles) -chris <http://www.mythtech.net>

24 years, 1 month

DEC distribution tapes - VAX vs RISC

by PeksaDO＠Cardiff.ac.uk

Sorry about the HTML - I have now discovered a difference between Pegasus mail V3 and Pegasus mail v4 - V3 worked properly, V4 puts ****ing HTML everywhere ****ing where. Apologies Doug.

24 years, 1 month

Orange donation

by dhquebbeman＠theestopinalgroup.com

> Yesterday we visited Computer Solutions in Orange, NJ and were given a > lovely HP3000 Series 70. It's a large, but very lovely beastie and so > far, at least, remarkably tractable. Also in the load were boxes of > paper tape, tape reader , full 3000 docs and an HP2108. They also gave > us an Apollo 400 system, server and 6 workstations. Very nice people, > and aa lovely donation. Without a doubt... say, was this from inventory (stuff they sell), or something they once-uon-a-time used? -dq

24 years, 1 month

Semi-OT: PMac 6100 DOS

by dhquebbeman＠theestopinalgroup.com

> Well.. there are two different video "adaptors" that were > being refered to in that thread. [..snip..] > The question that seems to have come up is, does the 6100 DOS card have > that loopback connector at all? The PCI DOS cards can either use the the > external loop connector... OR an internal connector for Macs that support > it (you need the GIMO slot, which many of the PCI Powermacs had). There > is a possibility the 6100 card does something similar. There is a cable with three or four connectors attached to it; I assume this is what you're referring to. The package is complete, the packing list is still there, I can bring it in tomorrow and scan it. Regards, -dq

24 years, 1 month

[GreenKeys] News item for WC2XPF (fwd)

by dhquebbeman＠theestopinalgroup.com

> Gonna go Google this, but I was pretty sure Ralph Bemer invented ^^^^^ Bob, Bob, Bob, Bob (second time this year I've done this!) -dq

24 years, 1 month

[GreenKeys] News item for WC2XPF (fwd)

by dhquebbeman＠theestopinalgroup.com

> John F. Auwaerter, 76, of Park Ridge, was a pioneer in the > telecommunications industry who was instrumental in the development of > the American Standard Code for Information Interchange, or the ASCII > computer language. Shades of Al Gore, this "I was first" disease knows no boundaries... Gonna go Google this, but I was pretty sure Ralph Bemer invented ASCII .... -dq

24 years, 1 month

Need Best Z-80 Disassembler

by pete＠dunnington.u-net.com

On Mar 15, 11:09, Douglas Quebbeman wrote: > I have a few disassembler stored on some archive > somewhere. But on the chance that a lister might > know of a more modern Z-80 disassembler than what > I'm likely to have, I thought I'd post a query. I use dz80, which you can find at http://www.inkland.org/dz80/index.htm I see the current version is 2.0 (March 2002), but I use 1.31 (June 1999). Actually, I made a few small changes to make the unix version work more like other unix software (mostly to do with option letters and arguments, which were strange and DOS-like in the original, and to allow use of hex and octal in addresses and output, plus a couple of bugfixes for long jumps). -- Pete Peter Turnbull Network Manager University of York

24 years, 1 month

NEWS: Old Atari games play on Sony Ericsson phones

by bpope＠wordstock.com

Jus' a little news blurb: Mar 14, 2002 8:30 AM PT Old Atari games play on Sony Ericsson phones Mobile phone maker Sony Ericsson on Thursday announced partnerships with two companies making games for mobile phones in its drive to challenge handset market leader Nokia through mobile entertainment. The newly formed handset maker, Sony Ericsson, said partnerships with iFone and Synergenix would enable consumers to download some games for free from the Sony Ericsson Web site, or access others for a fee from an operator's Web site. IFone will be providing games from its Atari catalogue, including classics such as Asteroids and Pong. --Reuters This is from: http://zdnet.com.com/2110-1105-859957.html Cheers, Bryan P.S. Happy PI day!!!

24 years, 1 month

Need Best Z-80 Disassembler

by dhquebbeman＠theestopinalgroup.com

Well, The subject says it all... I have a ROM (a 2764 I think, it came to 8K bytes) I need to render into the most readable source code possible. It is Z-80 executable, and contains ASCII strings that have their high-order bits set (yes, PR1ME). I have a few disassembler stored on some archive somewhere. But on the chance that a lister might know of a more modern Z-80 disassembler than what I'm likely to have, I thought I'd post a query. This need comes after having acquired and replaced every single board in my Prime, only to still have it be non-operational. Thanks in advance, -doug quebbeman

24 years, 1 month

VAXBI fun continues - seeking DEBNT installation docs

by Antonio.Carlini＠riverstonenet.com

> Ethan Dicks wrote: > >ports. No DMB32 or anything like that (not that I would mind locating >one of _those_ either). If only you'd asked 18 months ago :-) >As you can see, it's a full boat - 16MB of RAM in 5 cards. I'd love to >run across an inexpensive MS820-CA or two. I wouldn't mind pulling the If only you'd asked ... :-( >MS820-AAs out, but 16MB is an OK amount of memory for a single user. I'm >also on a long-term quest for free or nearly free KA825 boards - I'd be >nice to bring this up to an 8350. If ... No, done that enough for one email. If you can get three KA820s (or KA825s) you should be able to get that to work too! (But you cannot mix KA820 & KA825). >right from looking at where the Lance chip is on the DEBNT. If anyone >has installation instructions, particularly cabling instructions, >those would be very helpful. The Owner's Manual is available at: http://208.190.133.201/decimages/moremanuals.htm as is the Installation Guide. I *thought* I'd also scanned and sent an install guide for one of the VAXBI ethernet options, but I guess not. When I had one in the lab, my VAX 8350 just mostly worked so I don't have too much experience of playing with the ethernet. The DSB32 and DMB32, and the CPU(s) and memory were all pretty straightforward. The only funny I remember with ethernet is that you need to cable up a little bit extra for the power required by the AUI in the bulkhead. But that may well have been the VAX 6000 ... Antonio

24 years, 1 month

VCF on MediaTelevision

by csmith＠amdocs.com

> -----Original Message----- > From: M H Stein [mailto:mhstein@canada.com] > Freedom Fighters? Revolutionaries? Wow! And I thought we > were just weirdos & nerds... I think the politically correct term is "futurist" ;) Chris Christopher Smith, Perl Developer Amdocs - Champaign, IL /usr/bin/perl -e ' print((~"\x95\xc4\xe3"^"Just Another Perl Hacker.")."\x08!\n"); '

24 years, 1 month

Atari PC3000

by KenzieM＠sympatico.ca

I saw one of these yesterday. It looks like a monitor with floppy drive in the bottom, at the back was a plug for the power and another labelled video. I could not see anyplace for a keyboard to be attached. Does anyone know anything about this machine? Collector of Vintage Computers (www.ncf.ca/~ba600)

24 years, 1 month

[Maybe OT] A/UX installation

by dhquebbeman＠theestopinalgroup.com

> > cdrecord -speed 8 -dev 0,6,0 -eject -v AUX_3.0.1_Install.toast_image > > I don't know if this works or not. I don't know if the image is "real ISO" > (I used Toast, so I couldn't say). > > > When I try to boot up on a IIci, the floppy works ok, and it starts to > > search for the CD in the CD drive. The cd drive is a toshiba 5401B, I > > pulled from an alpha. It never finds a valid disk. So, to try to > > figure out what was wrong, I used BasiliskII (a mac-on-unix emulation) > > and tried to mount the CD image as a disk under system 7.6...and it > > wanted to format it. Should the CD be mountable? > > No, it shouldn't be. Toast complained about it too, but it worked fine > for installation. The boot disk is needed to mount it. I have lots of trouble with older 68k Macs that were used by clueless lusers... in particular, here at my current orkplace, our #1 Mac advocate didn't realize you have to power off the system and SCSI devices when attaching them/ removing hem from the chain. I'm not sure what goes bad after five years of connecting/dosconnecting with the power on (the terminator resistors shouldn't be affected, should they)? But I run into this a lot; I have little luck with CDs on Macs, and more trouble with outboard drives in general than I'd care to say... -dq

24 years, 1 month

Semi-OT: PMac 6100 DOS

by dhquebbeman＠theestopinalgroup.com

> > > Chris , I'm sorry, you're totally wrong. The 26 pin connector is for an > > >Apple Audio Vision monitor. No F--king Dongle. > > I said a number of times, I have NOT used the DOS card that works with > > the 630/6100... and that is the card in question. > > > > But I CAN tell you that EVERY OTHER dos card Apple made, needs a video > > dongle... and they ALL connect via a DB-26 connector on the back of the > > DOS card... which is exactly what the person described on the back of > > their DOS card. > > > > Now, it is quite possible that Apple put an AppleVision port on the > > 630/6100 DOS card, why, I would have NO idea, since the 630 can't use an > > applevision monitor... but maybe they did. > > > > HOWEVER, on the back of the 6100... is an HDI-45 video port... THAT is an > > AppleVision video port. That is NOT the same thing as the DB-26 on the > > DOS cards. Totally different port, totally different function. > > BUT... I have heard that you do not need a video dongle with the 630/6100 > > DOS card... I just can't confirm it one way or the other... and again, > > since they are describing EXACTLY what will happen to a Quadra 610 > > Houdini DOS card if the dongle is not connected... I felt it was a good > > guess that they might in fact need one. > > > > Now I am REALLY going to have to get 630/6100 DOS card... just so I can > > figure out once and for all if it needs a video dongle (or do you prefer > > the term... video loopback connector) I've never heard these called "video dongles", and while they don't come in the package with the 6100 DOS board, the manual says it's needed, shows its picture, and says it comes with the computer in which you're trying to install the board. Complete package, appears not to have ever been installed, the red Apple seal is still intact on the diskette pack (but was easily pried open by yours truly while checking). I think I even have a 6100 for it to go in, but dunno what I'll ever do with the mess... -dq

24 years, 1 month

impressive CI - SCSI storage rack from MTI (RAID?)

by gunther＠aurora.regenstrief.org

Hi ho, now I hauled it home, the modules of this very impressive MTI StorageWare assembly. It's a marvellous piece of super redundant 24/7 operational gear for any VAX cluster. The fun starts with a box that probably emulates an HSC90 or so, that one has two power supplys, and there are two of those boxes each having the 4 redundant CI connectors. Each box has 3 SCSI (?) connectors that run to another 4-box assembly and there is another layer of redundancy. Then all this drives 4 arrays of 4GB SCSI disks each having 8 such disks. I conclude that this must be a RAID array, because I don't know how else one could address 8 disks on a SCSI bus (isn't 7 devices appart from the controller the maximum?) Initially it seemed straight-forward to use as a simple CI/HSC to SCSI adapter, but now it looks like this stuff is best kept as one big impressive unit. I'm going to try find the manuals for this too. Does anyone have experience with this kind of gear? regards, -Gunther -- Gunther Schadow, M.D., Ph.D. gschadow(a)regenstrief.org Medical Information Scientist Regenstrief Institute for Health Care Adjunct Assistant Professor Indiana University School of Medicine tel:1(317)630-7960 http://aurora.regenstrief.org

24 years, 1 month

Macintosh Portable power supply?

by dan＠ekoan.com

I recently acquired a Macintosh Portable (M5120) but it came without a power supply. Does anyone have a spare they'd like to get rid of? Cheers, Dan

24 years, 1 month

MicroVAX-II questions

by mcguire＠neurotica.com

On March 8, Doc Shipley wrote: > Just got home with my brand-spanking-old MVII and set about playing > with it. It's indecently clean inside, cables all in good shape, fans > all free and clean, cards well seated. Sounds like a girl I once knew. > I even managed to get them all back in properly, in order, and the > cables connected right. This too. > This means I would, if I had the distribution hardware for the DHQ11s, > have 25 serial interfaces? (plus console) What exactly is the DMV11? > "Synchronous communications controller" sounds like it requires a DMV11 > on the other end as well. It's a sync serial interface...you'd connect it to a CSU/DSU and a leased line, or something similar. > Everything VMS I've looked at says the DEQNA is unsupported in VMS > >v5.2. Is that unsupported as in "don't call DEC/Compaq/HP", or > unsupported as in "it don't work"? Am I stuck with NetBSD then? Does > anyone know if NBSD will mop-boot over the DEQNA? I don't have VMS > older than 6.2. DELQAs are fairly easy to come by. If you want one and can't find one immediately, email me. > Anybody have 2 breakout boxes for the M3107, and no M3107? We could > equalize.... For that matter, if anybody needs the card, I'll just > share. I might have one of these, I will check. Email me if you don't hear back about this by the end of the weekend. > You know you're over the edge when the lack of ethernet access in your > garage is a problem. Nah...that's just a *start*. -Dave -- Dave McGuire St. Petersburg, FL "Less talk. More synthohol." --Lt. Worf

24 years, 1 month

Heads up... free MVII/PDP-11 on eBay UK

by alan.pearson＠cramer.com

> > Apparently, this chap has a free PDP11 & MicroVax-II going to > > a good home... > > > The PDP-11/73 will be taking a car journey here next week ... I think - but > am not sure - that the Vax is also spoken for. AAAAAAAAAAAAAAAAAAAARRRRRRRRRRGGGGGGGGGGHHHHHHHHHHHHHHHHHH!!!!!!!!! Digest blues strike again :-) Ah well. Al.

24 years, 1 month

Breaking into my Newton

by mythtech＠mac.com

>Of course, the problem is that it's password protected and stuffed if I >know what it was. Any ideas on how to break in (I suspect after so many >years I don't really care about the data although it'd be fun to find out >what I saved there). > >This is an Original Messagepad running OS 1.3. IIRC, if you hold the power button ON (slide the switch down like you are turning it on, but hold it down), and then press the reset button inside the battery compartment... that will wipe the system memory. That will reset the password as well as wipe out EVERYTHING you might have had loaded.... basically it defaults it back to factory settings. (Although, I think any system upgrades you installed are preserved). There is probably a tech note about this on Apple's web site, as it was a fairly common issue back in the Newton days. -chris <http://www.mythtech.net>

24 years, 1 month

VAXBI fun continues - seeking DEBNT installation docs

by erd_6502＠yahoo.com

Since I have the hood open on my 8200, I thought I'd diagnose the troubles I've been having with getting a DEBNT working in there. The 8200 I have came with a KDB50, 4MB RAM and one CPU. Nothing else (and was $13,000 when my former employer bought it - I just re-found the receipt). The only serial ports are the four console ports. No DMB32 or anything like that (not that I would mind locating one of _those_ either). Since it first arrived, I put in more RAM, COMBOARDs (that we made) and a DWBUA (which I'm diagnosing for its own problems). I am now attempting to use a DEBNT I received some time back. Here's what it looks like inside... T1001 KA820 - 8200 CPU T1010 DWBUA - Unibus adapter T1001 KA820 - 8200 CPU (not installed at present) T1002 KDB50 - KDB50 SDI adapter T1003 KDB50 - KDB50 Processor board T1019 MS820-BA - 4MB RAM for VAXBI processor T1019 MS820-BA - 4MB RAM for VAXBI processor T1019 MS820-BA - 4MB RAM for VAXBI processor T1008 MS820-AA - 2MB RAM for VAXBI processor T1008 MS820-AA - 2MB RAM for VAXBI processor 1294 CBSBI - COMBOARD-BI (sync comms front end processor) T1032 DEBNT - Ethernet and TK50 controller (I used http://www.stmarks.pp.catholic.edu.au/vax/VAXBI.html for reference) As you can see, it's a full boat - 16MB of RAM in 5 cards. I'd love to run across an inexpensive MS820-CA or two. I wouldn't mind pulling the MS820-AAs out, but 16MB is an OK amount of memory for a single user. I'm also on a long-term quest for free or nearly free KA825 boards - I'd be nice to bring this up to an 8350. The disks are 3rd-party ESDI (1.2Gb each) drives on a 3rd-party ESDI- to-SDI controller. Very nice. Beats an RA81 hands down. At the moment, I'm running VMS 5.4 and plan to continue for some time (due to compatibility needs for the COMBOARD stuff I used to write). I do have a pair of RA70s I was thinking of putting on it as well. So... the DEBNT itself fails self-test if there is nothing attached to the AUI connector. If I attach a DEC loopback connector to the AUI plug, ISTR I get the yellow LED telling me it passed. If I put a 10BaseT transceiver on there, the TX light stays lit with no networking drivers/software loaded. First and foremost, I'm attempting to verify I put the cables on the right places. I have 30-pin connector off one end of the AUI cable. I have a 30-pin connector with one wire attached that seems to be a jumper block of some kind. At the moment, they are attached to the BI backplane at block "E", I think because that's what seemed to be right from looking at where the Lance chip is on the DEBNT. If anyone has installation instructions, particularly cabling instructions, those would be very helpful. Once I get the hardware happy, I'll need to move to software. Since I want to stay at VMS 5.4, what are my TCP/IP options as a hobbyist? The only other VAX I have set up with Ethernet is also running 5.4 - a uVAX-II with a DEQNA. I do have VMS 6.1, but I'm not using it at the moment. Thanks for any DEBNT and VAXBI tips and hints. I have some docs, but not everything. Mostly, I'm drawing on general VAX experience combined with observation and experimentation. I know my way around the VAXBI bus, but not around some of the peripherals. -ethan __________________________________________________ Do You Yahoo!? Yahoo! Sports - live college hoops coverage http://sports.yahoo.com/

24 years, 1 month

Fun with a DWUBA

by ethan_dicks＠yahoo.com

--- Gunther Schadow <gunther(a)aurora.regenstrief.org> wrote: > Ethan, I'm glad to hear you are making headway in fixing your > fried board... I was up to my elbows in the 8200 last night. I think I've identified the target pin on the DD11DK that is the destination of the damaged pin in the first place - BB2 which is defined as a ground. This is odd because on the paddle card, the signal is individually routed over pin 30 of JP2 and is not tied to anything else on either end. Having inspected the cable carefully, multiple times, I'm still scratching my head as to how the damage could have happened in the first place. I had notes written right on the Unibus cables where they stick onto the back of the VAXBI - the notations match the docs (I have the DWBUA technical manual with installation instructions). I can't even see how putting the paddle card in backwards would have caused a massive problem. I'm afraid to hook everything up and power it on again before I identify what was wrong. OTOH, I did drop the T1010 card in the VAX and look for its presence on the bus. With the cables disconnected, the card fails self-test (Duh!) but when I go to read the ident register of the DWBUA (E 20000000), I get back FFFFFFFF, not the expected value (as documented in the manual). Having written VMS VAXBI drivers in the past, I can say that this is not good. The card "shows up" - the POST shows a "-0", so the VAXBIIC of the DWBUA is detected, but it's exceedingly unhappy. I am suspecting that the card is more fried than one chip. I'll keep working on it to see if the card needs a rudimentary amount of attachment to the UNIBUS to get far enough into its self-test to initialize the ident register, but I'm not hopeful about it - I think it should show the world what it is, even if it's unhappy. Fortunately, I have docs for all of this. At this time, I suspect the M9313 UET, the DD11DK, the cables and the T1010 card. I just have to narrow down the list of suspects. I suppose I could drop the card in with the chip at risk removed and a lead hanging out so I can monitor what's happening on that pin. The pin itself happens to go to the outer-most pad on the VAXBI bus, looking at the board, it's the farthest pad >from the VAXBIIC on the solder side. It goes diagonally in more-or-less a straight line to a pin of a DEC DC021C, 4 or 5, IIRC (it's not in front of me here). Either that pin sources a whopping amount of current >from the DC021 and it was shorted to ground by a bad cable or a problem in the BA11, or somehow a very wrong voltage came from the BA11 into that pin. It's the only way I can see how a trace can get cooked and the chip melted at that pin. Back to the basement... -ethan ===== Visit "The Seventh Continent" http://penguincentral.com/penguincentral.html __________________________________________________ Do You Yahoo!? Try FREE Yahoo! Mail - the world's greatest free email! http://mail.yahoo.com/

24 years, 1 month

Free books in Irvine, CA - mostly Apple IIc/e

by mythtech＠mac.com

>Is this the manual for the thermal AppleScribe printer? ... DOH! that was supposed to be sent off list... sorry -chris <http://www.mythtech.net>

24 years, 1 month

info on IBM 4-slot PCMCIA controller

by SUPRDAVE＠aol.com

In a message dated 3/14/2002 9:54:54 PM Eastern Standard Time, rschaefe(a)gcfn.org writes: << So far, all I've found is two or three references to it on IBM's site. Nothing comes up for the part number 40G1041. At least, I think it's the part number-- it looks like all the other part numbers. Pretty sure it's on topic too, at least the 82365s on the back are dated '92. Anyone know what the settings are? It's got a 4-position DIP switch for `SLOT ADDR, `IRQ', and `ROM ADDR', and also a slide-switch marked `BLK1 BLK0'. I wonder what that does. I hope I can put this thing to use--it's really pretty nice, at least to look at. It's got little solenoids to physically lock the cards in the slot. Only trouble (aside from not knowing what it's set for) is that it's just a hair too wide to fit into the two computers I've tried it in so far. Hope I can find something to put it in! >> Sounds like it fits the IBM PS/2 E, machine type 9533. -- Antique Computer Virtual Museum www.nothingtodo.org

24 years, 1 month

Xerox XPS v4.2-v4.3.8

by doc＠mdrconsult.com

What the heck is it? A stack of TK50 tapes - is it a VMS add-on, an OS, a printing subsystem or what? Doc

24 years, 1 month

urgent business/investment deal

by jhfine＠idirect.com

>minespower steel wrote: > VERY CONFIDENTIAL BUSINESS ATTENTION STRICTLY FOR YOU ONLY > > FROM THE DESK OF > ALHAJI USMAN YERIMA. > IKOYI, LAGOS. > PHONE;234-803-3088-100 > BUSINESS ATTENTION. > URGENT BUSINESS DEAL > > I am pleased to send my greetings to you, I know > this letter will definitely come to you as a surprise package, and you will be wondering how i came about your contact, actaully, i came about your contact when i was browsing through the internet, on looking for a trustworthy, confidential and honest partner with whom i can transact this business with, i then came about your contact and decided to contact you > > I am extending this proposal to you in my capacity as the chairman of the contractReview/Audit > Committee scrutinizing all record covering executed contract awarded byprevious > military government of Nigeria. My colleagues and I have uncovered afloating > amount of USD$22,500,000.00 (TWENTY TWO MILLION, FIVE HUNDRED THOUSAND > U.S.DOLLARS), without a clear beneficiary owing to a deliberate act of over > invoicing and inflating of contract value by some government officials.This > money (USD$22.5M),has already been approved for payment by the ministry of > Mines, Powerand Steel and is secured under . As top civil servants we are not authorized > to operate foreign bank account and this is why we want to use your bank account > to transfer this money outside Nigeria. We have accepted you as our foreign > partner and will now regularize the approvals to you as the trust beneficiary of > the contractsum.As soon as we receive your acceptance, we shall inform you of > the necessary requirements from you to facilitate transfer. Let us use this > opportunity toexploit the benefit of this sum. We have resolved to give 20% of > the totalsum as compensation for your assistance, 70% is for me and my partners > here in Nigeria, 10% is set asideto cover every expenses made in the course of > the transaction. Note that this should be confidential. Send your urgentresponse > strictly through my E-mail: usmanyerima(a)onebox.com,as this is a confidential mailbox Please do not fail to reply > me with your private Telephone and fax numbers for easy communication. > Yours faithfully, > > THANKS AND GOD BLESS > > USMAN YERIMA > > ps; while I await your reply at most by tuesday, if you do not reply, I > will have no choice but to find another alternative. Anyone interested in seeing where the money should be sent? Should be able to have a bit of fun. I though there had been enough publicity on this one that everyone would remember the Nigeria scam by now. Also, do any of the police in Nigeria care? Can police in any other country trace this sort of thing? Or do the police just say to toss it and forget it? Better have a well protected site - they may just be sending back a virus!

24 years, 1 month

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb