test-drb

test-drb@ccmp.vtda.org

101090 discussions

by Flash688＠flying-disk.com

Douglas Taylor <dj.taylor4 at comcast.net> wrote: > I just got one of these and wanted to configure it via the 10 > pin RS232 port on the board. > Is the port a standard DLV11-J type? Yes, it is identical. I was the original beta tester on the SCDC and used it extensively. In fact, the designers called it "the Frisbie port". :-) > I have one of those D-bit DLV11-J to DB25 adapters but not > getting any response. You may need a null modem. Try swapping pins 2 and 3. I can send you an genuine Andromeda DB25 adapter if you give me a mailing address and promise to send me $10. :-) > Any info on the few jumpers on the board? They changed between the original Rev. A and final Rev. F boards. Which one do you have? I can send you a copy of the manual, complete with all my editorial comments written on it. Alan "Packrat" Frisbie

8 years, 4 months

8085 Dissasembly?

by bygg＠cafax.se

Bill Gunshannon wrote: > Many of us think that the advent of the x86 architecture is what led to > masochism. ... or masochism led to the x86 architecture. > bill --Johnny

8 years, 4 months

sugar packjets anyone ever come across em?

by tdk.knight＠gmail.com

anyone ever come across sugar packets? this came in a lot of manuals and documents that arived the other day kinda neat https://imagizer.imageshack.com/v2/800x512q90/922/T4MCLS.jpg

8 years, 4 months

RL Drive Terminators

by bill.gunshannon＠hotmail.com

I see some company selling them on eBay for $122.? Are they really worth anything like that?? I have a couple sitting around here somewhere that I don't expect to ever use again.? Just wondering if they are worth looking for to sell.? In this hobby you can always use money for new (well, old actually) toys. bill

8 years, 4 months

To be scrapped in as little as 2 months

by pete＠petelancashire.com

3 x DEC Alphas, small deskside models 5 to 6 x Sun pizza boxes one a Sparc 1 prototype 029 IBM Keypunch The day I can have a 15 cubic yard scrap metal drop box the stuff will start to be tossed in. All based on when the rains stop and the ground is hard enough I can't want much longer For those that have not seen me post this before The stuff is near (3 - 4 miles outside of) Banks Oregon USA (look it up on Google). I CAN NOT LIFT OVER 10 LBS, PERIOD. -pete

8 years, 4 months

Manual wanted for the MFE M-700 Floppy-Disk-Drive

by harten＠injectstar.de

Hi to all! I'm looking for a technical manual/schematic for the Mayflower MFE M-700 8 inch Floppy-Disk-Drive. Regards Rolf

8 years, 4 months

new disassembler vs IDA (was Re: 8085 Dissasembly?)

by spacewar＠gmail.com

On Wed, Apr 18, 2018 at 8:17 PM, Mark J. Blair via cctech < cctech at classiccmp.org> wrote: > Some of the future reverse engineering projects I have on my to-do list > involve the CDP1802 processor, which IDA presently doesn't support. When I > get to them I'll have to decide whether to use dismantler vs. learning how > to add CDP1802 support to IDA. I'm leaning towards the latter, because IDA > is so much fancier than dismantler is. I'd vote for adding it to dismantler. I had an IDA Pro license at one point, but I seem to have misplaced it, and it is too old to get me any discount on a new release. I imagine that IDA has probably improved a lot since back then, but at the time it had a pretty awful user interface. If I had an actual business need to reverse-engineer something using a processor that IDA supported, I'd certainly buy a new IDA license, but I wouldn't personally invest any time in building add-ons for expensive commercial software, when there are open source alternatives that may not be as good, but are generally good enough. For the 1802, I've used a really crude disassembler written in C. The 1802 instruction set isn't very complicated, so a disassembler for it isn't either. It's been so many years since I actually disassembled 1802 code that I'm not sure I still have the disassembler around.

8 years, 4 months

Andromeda SCDC Qbus controller question

by dj.taylor4＠comcast.net

I just got one of these and wanted to configure it via the 10 pin RS232 port on the board. Is the port a standard DLV11-J type? I have one of those D-bit DLV11-J to DB25 adapters but not getting any response. Any info on the few jumpers on the board? Doug

8 years, 4 months

what happened to the dec thing with the butterfly discs never heard back I need it for museum thanks cindy ed

by couryhouse＠aol.com

what happened?to the dec thing with the butterfly discs never heard back I need it for museum thanks?cindy ? ?ed

8 years, 4 months

old schematics books

by sales＠elecplus.com

These have now been claimed. Thanks everybody! Sean I need an address please! Cindy Croxton Electronics Plus 1613 Water Street Kerrville, TX 78028 830-370-3239 cell sales at elecplus.com AOL IM elcpls --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus

8 years, 4 months

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

2001

2000

1999

1998

1997

test-drb