>Do your manuals include the Zebra MC68020 executive firmware manual, or the
>OMTI controller docs?
I have the following (I guess I should have done this before, but I was
too lazy):
Accu-Plot Operator Guide Zebra/Pick graphics system
Compu-Sheet operator guide for financial planning
Pick Jet word processor guide
Runoff reference manual
Pick Spooler reference manual
Proc reference manual
Pick Basic reference manual
Zebra 2500 Installation Guide
Zebra Models 2500 and 3500 Cipher 1/2" Tape Unit Installation Guide
Overview of the Pick Operating System
Introduction to Pick TCL and file structures
Pick operator guide
Pick utilities guide
Access reference manual
Editor reference manual
So in answer to your question... no, I don't have either of the manuals
you are looking for.
-chris
<http://www.mythtech.net>
>From: "ben franchuk" <bfranchuk(a)jetnet.ab.ca>
>
>Dwight K. Elvey wrote:
>
>> It has been a while since I had the machine running. I can
>> fire it up and check what I have. The only issue I have for
>> making copies for others is the media. I only have a few
>> hard sectored disk. For some reason, I thought that disk
>> formats would last at least as long as 33 lp records. I
>> didn't realize at the time that media was being obsoleted
>> as fast as it was produced. I know better now.
>
>The funny thing some small record companies still produce
>records.You can still get records, but not the crappy $7.95 k-tell
>stuff, but higher priced and higher quality audio.A good
>record changer and other assorted parts ( like a clean record)
>is better music wise than any CD.
>
>Can a regular disk be punched to make hard sectored disc?
>Ben.
>
Hi Ben
Yes, one can take normal disk and punch them. They do
need to be accurately done. I've been looking at setting
up an index wheel to do just this. I have need for
doing it on 5-1/4 and 8 inch so it is an interesting
problem. One of my 8 inch applications has index holes
on the outer diameter of the disk.
Dwight
>If anyone on here is from the UK, they might want to take a look at
> >http://computerhardwareneeded.cjb.net and read this guys story
I'm a Brit in the USA.
Most of us are friendly helpful folks.
Most of of us become unfriendly when directed to a website that tries to
install Gator spyware on our machines, like you just did...
Mike
http://www.corestore.org
_________________________________________________________________
Stopped by one of my better scrounging places yesterday. I left with a new PC CMOS RAM card. This card has on-board battery backup, utilities in on-board ROM, write protection ability, and can be used as a solid state RAM drive and you can even boot from it. Also got the manual with it :-)
Other goodies include two of the MS-DOS co-processor cards for the HP 9000 series 200 and 300 computers. I don't need to run MS-DOS on the 9000s but this card is required before you can use the HP 9127 drives to read and write MS-DOS formatted disks. I've got a heap of 9127s so the cards are very welcome. Anybody have docs or SW for these? I'm not sure if SW is required to use them to read/write MS-DOS disks or not.
Also found a NICE little 5 slot VME chasssis made by Performance Technologies. It has two cards in it but I haven't checked it out yet to see what they are.
Also found a nice counting scale with a remote scale. Also a big pile of Endevco Charge Amplifiers. Parts of a HP VXI chassis. Also found a 19" rack with a Recognition Concepts Inc Trapix 2d system. The odd thing about it is that the cards appear to be exactly the same size and connector layout as DEC Hex-bus cards! In the same chassis was a rackmount PC. It was connected to the RCI system by several LARGE ribbon cables and appears to be the I/O and storage system for the system. I didn't see much use for the RCI system so I left it but I grabbed the rack mount PC and a second loose rack mount PC that seems to be a spare.
Joe
>From: "Patrick Rigney" <patrick(a)evocative.com>
>
>> The hardware solution is to disconnect the internal serial cable from the
>> termianl logic PCB (the rearmost vertical PCB in the machine) and replace
>> it with one of the cables that goes to a DB25 connector on the back
>> (these cables are normally connected to the serial port PCB plugged into
>> the computer mainboard, just in front of the terminal logic PCB). The
>> cables have a Molex 0.1" pitch SIL connector on the end, and fortunately,
>> the pinout of all the internal serial connectors (terminal logic PCB,
>> computer 'console port', serial port PCB) is the same.
>
>Ouch...
>
>> The software solution is to write a little program that transfers
>> characters between the computer's console port and one of the other
>> serial ports. This will then make the computer section appear as a
>> transparent link between the terminal and the outside world.
>
>much easier than any of the above... get a copy of MDM712 or similar
>terminal emulation program. MDM712 comes with a serial port driver for
>H8/89. Plug your device into the spare serial port on the back of the
>(unopened) machine, and that should do it. Some '89's have three-port
>serial cards... I don't know which ends up being which or whether MDM712
>lets you choose, all of my '89's are down right now. :-/
>
>Patrick
>
Hi
Why would you assume that finding and installing some
software would be easier than making up a simple molex adapter
connector. As I recall, it was a 9 pin molex but I could
be wrong. That is all of 9 wires to deal with.
Dwight
This might work, if you can get at EDT in the state before
SYSTARTUP_VMS executes.
I haven't tried it to see if you can.
http://h71000.www7.hp.com/wizard/faq/vmsfaq_004.html
Who remembers how you could interrupt an RSX startup and
then, with luck,
PIP your way out of trouble with files that shouldn't have
been there?
Don Mitchell