10 Nov
2020
10 Nov
'20
10:47 a.m.
Something that's always worked for me: when soldering a male DB
connector (DB9, DB25, whatever -- or really any male/pin style
connector), plug it into a mating female connector first. That will hold
the pins securely in place and prevent them from sagging in the plastic
of the body if your soldering iron is too hot or you hold it on too long.
--
**Richard
10 Nov
10 Nov
12:44 p.m.
now thats a pro tip
On Tue, Nov 10, 2020 at 12:47 PM Richard Milward via cctalk <
cctalk at classiccmp.org> wrote:
Something that's always worked for me: when
soldering a male DB
connector (DB9, DB25, whatever -- or really any male/pin style
connector), plug it into a mating female connector first. That will hold
the pins securely in place and prevent them from sagging in the plastic
of the body if your soldering iron is too hot or you hold it on too long.
--
**Richard
1 p.m.
On Tue, Nov 10, 2020 at 1:47 PM Richard Milward via cctalk
<cctalk at classiccmp.org> wrote:
Something that's always worked for me: when
soldering a male DB
connector (DB9, DB25, whatever -- or really any male/pin style
connector), plug it into a mating female connector first. That will hold
the pins securely in place and prevent them from sagging in the plastic
of the body if your soldering iron is too hot or you hold it on too long.
Yep. Been doing it that way for a lot of years. Good tip!
-ethan
9:25 p.m.
Same here. Also works for soldering header pins etc.; stick a matching
connector on the other side of the board and they stay flush and
perpendicular.
On Tue, Nov 10, 2020 at 11:43 PM Ethan Dicks via cctech <
cctech at classiccmp.org> wrote:
On Tue, Nov 10, 2020 at 1:47 PM Richard Milward via
cctalk
<cctalk at classiccmp.org> wrote:
Something that's always worked for me: when
soldering a male DB
connector (DB9, DB25, whatever -- or really any male/pin style
connector), plug it into a mating female connector first. That will hold
the pins securely in place and prevent them from sagging in the plastic
of the body if your soldering iron is too hot or you hold it on too long.
Yep. Been doing it that way for a lot of years. Good tip!
-ethan
10:02 p.m.
On 11/10/20 9:25 PM, Mike Stein via cctech wrote:
Same here. Also works for soldering header pins etc.;
stick a matching
connector on the other side of the board and they stay flush and
perpendicular.
Nice tip, but I thought that most folks knew about the
matching-connector thing! I guess unwritten knowledge gets lost over
the years.
--Chuck
11 Nov
11 Nov
1:02 p.m.
On Tue, 10 Nov 2020, Chuck Guzis via cctalk wrote:
Nice tip, but I thought that most folks knew about
the
matching-connector thing! I guess unwritten knowledge gets lost over
the years.
. . . such as turning a bolt backwards a little to find the start of
thread?
. . . or attaching some plastics with cyano-acrylate AND running a
soldering iron over the glued joint
. . . using a large vise as a crude substitute for a press, using sockets
as drifts for pressing round objects, . . .
(all of which I have seen in the last few years as "fresh tips")
Half a century ago, a soldering work station included a lot of mating
connectors and a padded vise. Has the use of a vise been forgotten, also?
SOME learned the hard way that using connecctors of current hardware to
hold ones being soldered carried some risk.
If you compare "Woodwright's Shop" with "New Yankee Workshop",
even significance of grain is being gradually eroded and ignored.
Written knowledge doesn't get preserved, either. "The internet is written
in sand".
"Standard procedure" in library stack culling is to remove any book thata
hadn't been checked out in a set period of time. A decade ago, when I was
re-assigned as one of the college's librarians, I implemented an added
step of those books being on a set of shelves to facilitate looking them
over and over-riding as needed. (K&R and Knuth were slated for discard!)
--
Grumpy Ol' Fred
2:19 p.m.
I've not had issues just soldering the wires on. I'll admit I do use leaded
solder.
Dwight
________________________________
From: cctalk <cctalk-bounces at classiccmp.org> on behalf of Fred Cisin via cctalk
<cctalk at classiccmp.org>
Sent: Wednesday, November 11, 2020 1:02 PM
To: General Discussion: On-Topic and Off-Topic Posts <cctalk at classiccmp.org>
Subject: Re: Soldering DB connectors
On Tue, 10 Nov 2020, Chuck Guzis via cctalk wrote:
Nice tip, but I thought that most folks knew about
the
matching-connector thing! I guess unwritten knowledge gets lost over
the years.
. . . such as turning a bolt backwards a little to find the start of
thread?
. . . or attaching some plastics with cyano-acrylate AND running a
soldering iron over the glued joint
. . . using a large vise as a crude substitute for a press, using sockets
as drifts for pressing round objects, . . .
(all of which I have seen in the last few years as "fresh tips")
Half a century ago, a soldering work station included a lot of mating
connectors and a padded vise. Has the use of a vise been forgotten, also?
SOME learned the hard way that using connecctors of current hardware to
hold ones being soldered carried some risk.
If you compare "Woodwright's Shop" with "New Yankee Workshop",
even significance of grain is being gradually eroded and ignored.
Written knowledge doesn't get preserved, either. "The internet is written
in sand".
"Standard procedure" in library stack culling is to remove any book thata
hadn't been checked out in a set period of time. A decade ago, when I was
re-assigned as one of the college's librarians, I implemented an added
step of those books being on a set of shelves to facilitate looking them
over and over-riding as needed. (K&R and Knuth were slated for discard!)
--
Grumpy Ol' Fred
12 Nov
12 Nov
10:43 a.m.
Crimp pins 100%!
-----Original Message-----
From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Chuck Guzis via cctalk
Sent: Wednesday, November 11, 2020 8:11 PM
To: dwight via cctalk <cctalk at classiccmp.org>
Subject: Re: Soldering DB connectors
On 11/11/20 2:19 PM, dwight via cctalk wrote:
I've not had issues just soldering the wires on.
I'll admit I do use leaded solder.
Dwight
Also, tinning each wire lead before soldering to the connector helps.
Truth be told, I prefer crimp pins.
--Chuck
1282
days inactive
1284
days old
8 comments
8 participants
participants (8)
-
cclist＠sydex.com -
cisin＠xenosoft.com -
dkelvey＠hotmail.com -
ethan.dicks＠gmail.com -
mhs.stein＠gmail.com -
rsmilward＠frontier.com -
tdk.knight＠gmail.com -
w2hx＠w2hx.com