Yes Paul.
I've seen that tuning fork Watch from Bulava somewhere on the net when
I've searched fo the how to build a clock source with that.
I've even bought an small Tuning Fork device from Murata at ebay,
(think this one:
https://www.ebay.de/itm/327046203698)
It cost me som Effort to get the Murata People searching for any data on
that kind of old devices..
There are 2 types: One for Oscillators and the 2nd as resonator in
receivers. This one is a receiver device.
They where used for tone coded selective calls over radio networks.
That thing is small, approx 1,5cm long.. and that's the problem, it doesn't
want to much power applied to it. Lay'd it at side for now, don't want
to toast it with 100V pulses from a Thyratron.
Guys, please..let all the other devices besides for now. I would prefer
an low frequency xtal, because it's much easier to work with ..if I could
hopefully get one, that's why I'm asked for.
For an tuning fork I had to build an Oscillator with an pickup and an
excitation coil .. again..using an neon bulb or an Thyratron as amplifier.
That's a can or worms. For sure, it could be built and if I get no luck
with an crystal, I would go that way.
Currently I'm using the two decatrons that provide the 1Hz clock out of
the power grid frequency of 50Hz, no Motors, no Camshafts, no exhaust
Valve.
..that's working for now and it should even work for an daily used
clock..when the circumstances hee wheren't not special also.
(I'm getting my power out of 3 5KVA Inverters in 3 phase connection
from 48V LiFePo4 Accus, charged from the sun. If the cells are empty,
the Inverters are switching back to grid power..with relays. This gives
small Power glitches (brownouts) disturbing the clock reference.
You know, germany has the dumbest energy politics of the world..that's
the cause for the Photovoltaik, our energy prices are the highest of
the world because of stupid green politics.)
..so I need an reliable 1Hz source. No heated Tubes, no Transistors,
no Chips, no camshafts...
Please take a look at you electronic-dumpsters and find a usable xtal...
Regards,
Holm
Paul Koning via cctalk wrote:
The first electronic watch, the Bulova Accutron, used
a tuning fork. Those are nice and stable. I don't remember what frequency the
Accutron used, might have been 32768 Hz. Something ultrasonic would make for a small fork
and no audible noise.
FWIW, I think the standard watch crystal (also 32768 Hz) is in fact a tuning fork shape,
not the typical quartz slab found in higher frequency crystals.
paul
> On Nov 16, 2026, at 10:55 AM, Anders Nelson via cctalk <cctalk(a)classiccmp.org>
wrote:
>
> I'd like to see how a tuning fork works!
>
> --
> Anders Nelson
>
> On Mon, Nov 16, 2026, 10:53 AM TerraHertz via cctalk <cctalk(a)classiccmp.org>
> wrote:
>
>> i was about to suggest a tuning fork too.
>> I have a vintage "1KHz frequency reference" that is purely
>> electro-mechanical, but outputs a decent amplitude signal. The 'gain'
to
>> keep the tuning fork vibrating is provided by small carbon-granules
>> elements similar to early telephone microphones.
>>
>> If you're interested I can take some photos of it tomorrow.
>>
--
Technik Service u. Handel Tiffe,
www.tsht.de, Holm Tiffe,
Goethestrasse 15, 09569 Oederan, USt-Id: DE253710583
info(a)tsht.de Tel +49 37292 709778 Mobil: 0172 8790 741