Frank Leonhardt via cctalk wrote:
The favourite crystal supplier to radio amateurs
hereabouts is Krystaly
(
www.krystaly.cz). The seem to be able to sort you out with just about
anything.
Regards, Frank.
Thx,
I'll drop them a mail..
Regards,
Holm
On 16/11/2026 15:16, Anders Nelson via cctalk wrote:
> My first thought was to use a 555 timer as well, but I think the ask was to
> use no ICs. In any case, all digital logic was first created without ICs.
>
> --
> Anders Nelson
>
> On Mon, Nov 16, 2026, 10:12 AM<bitwiz(a)12bitsbest.com> wrote:
>
> > Is there any reason you can't either use a 555 or use a higher frequency
> > crystal and decade counters to divide or a small micro with a programable
> > timer (pico, nxp, altera, etc.)
> >
> > On Nov 16, 2026 8:21 AM, Anders Nelson via cctalk<cctalk(a)classiccmp.org>
> > wrote:
> >
> > Can you use decatrons? Each will divide by a power of ten.
> >
> > --
> > Anders Nelson
> >
> >
> >
> > On Mon, Nov 16, 2026, 8:43 AM Will Cooke via
cctalk<cctalk(a)classiccmp.org>
> >
> > wrote:
> >
> > >
> > > > On 11/16/2026 8:08 AM EST Holm Tiffe via
cctalk<cctalk(a)classiccmp.org>
> > > wrote:
> > > >
> > > > Hi all,
> > > ...
> > > > So here my question: Has anyone an xtal with an very low frequency
> > laying
> > > > around, which frequency can be devided down to 1 Hz (with ring
> > counters,
> > > > flipflops etc)? Maybe 1 oder 2Khz? ..or some other frequency that is
> > > > "dividable" to 1Hz?
> > > > Shouldn't be for nothing and I'm paying for the shipping (to
germany).
> > > >
> > > > This is not the last stand, but it can demonstrate what I'm
doing:
> > > >
> > > >
https://www.tiffe.de/images/uhr2.mp4
> > > >
> > > > Thx in advance,
> > > > Holm
> > > > --
> > >
> > > Hi,
> > > That's a really cool project. You obviously have more patience than
I.
> > I
> > > would like to see the final result.
> > >
> > > I've personally never seen a crystal lower than 10 KHz. I didn't
know
> > > such a thing existed. However, have you considered making your own? I
> > > have heard of that being done and have wanted to try it, but I haven't
> > > gotten around to it yet. In theory it should be relatively easy. Take
> > a
> > > chunk of quartz, cut it into a rectangle, and attach electrodes. Grind
> > on
> > > sandpaper and a flat surface until you get the right frequency. Of
> > course,
> > > once you cut the crystal you can only raise the frequency. "Crystal
> > > grinding" to raise the frequency used to be a common practice. I am
not
> > > sure about starting from scratch. I have seen very little of that. But
> > it
> > > might be worth trying if you the project hasn't already used up all
your
> > > patience!
> > >
> > > Good luck!
> > > Will
> > >
> >
> >
--
Technik Service u. Handel Tiffe,
www.tsht.de, Holm Tiffe,
Goethestrasse 15, 09569 Oederan, USt-Id: DE253710583
info(a)tsht.de Tel +49 37292 709778 Mobil: 0172 8790 741