Hmm I think it's going to be difficult to make a clock signal without at
least 1 tube or transistor . Maybe use a motor and cam to periodically
close a contact? If You use a synchronous AC motor, you should get very
close to some fraction of 50/60Hz.
--
Anders Nelson
On Mon, Nov 16, 2026, 10:21 AM Holm Tiffe via cctalk <cctalk(a)classiccmp.org>
wrote:
The goal is to use diodes, resistors, capacitors and
coils
(transformer, Relais for reset purposes), nothing more, at least no
active devices like thermoionic tubes, transistors or ICs.
The url from the linked video was buggy, I've wrote uhr2.mp4 instead of
Uhr2.mp4 ..corrected this, now both file names should work.
Regards,
Holm
Anders Nelson via cctalk wrote:
My first thought was to use a 555 timer as well,
but I think the ask was
to
use no ICs. In any case, all digital logic was
first created without ICs.
--
Anders Nelson
On Mon, Nov 16, 2026, 10:12 AM <bitwiz(a)12bitsbest.com> wrote:
> Is there any reason you can't either use a 555 or use a higher
frequency
> crystal and decade counters to divide or a
small micro with a
programable
> timer (pico, nxp, altera, etc.)
>
> On Nov 16, 2026 8:21 AM, Anders Nelson via cctalk <
cctalk(a)classiccmp.org>
> wrote:
>
> Can you use decatrons? Each will divide by a power of ten.
>
> --
> Anders Nelson
>
>
>
> On Mon, Nov 16, 2026, 8:43 AM Will Cooke via cctalk <
cctalk(a)classiccmp.org>
>
> wrote:
>
> >
> >
> > > On 11/16/2026 8:08 AM EST Holm Tiffe via cctalk <
cctalk(a)classiccmp.org>
>
> > wrote:
> > >
> > >
> > > Hi all,
> > ...
> > >
> > > So here my question: Has anyone an xtal with an very low frequency
> laying
> > > around, which frequency can be devided down to 1 Hz (with ring
> counters,
> > > flipflops etc)? Maybe 1 oder 2Khz? ..or some other frequency that
is
> > > "dividable" to 1Hz?
> > > Shouldn't be for nothing and I'm paying for the shipping (to
germany).
> > >
> > > This is not the last stand, but it can demonstrate what I'm doing:
> > >
> > >
https://www.tiffe.de/images/uhr2.mp4
> > >
> > > Thx in advance,
> > > Holm
> > > --
> >
> >
> > Hi,
> > That's a really cool project. You obviously have more patience than
I.
> I
> > would like to see the final result.
> >
> > I've personally never seen a crystal lower than 10 KHz. I didn't
know
> > such a thing existed. However, have
you considered making your
own? I
> > have heard of that being done and have
wanted to try it, but I
haven't
> > gotten around to it yet. In theory it
should be relatively easy.
Take
> a
> > chunk of quartz, cut it into a rectangle, and attach electrodes.
Grind
> on
> > sandpaper and a flat surface until you get the right frequency. Of
> course,
> > once you cut the crystal you can only raise the frequency. "Crystal
> > grinding" to raise the frequency used to be a common practice. I am
not
> > sure about starting from scratch. I
have seen very little of that.
But
> it
> > might be worth trying if you the project hasn't already used up all
your
> > patience!
> >
> > Good luck!
> > Will
> >
>
>
>
--
Technik Service u. Handel Tiffe,
www.tsht.de, Holm Tiffe,
Goethestrasse 15, 09569 Oederan, USt-Id: DE253710583
info(a)tsht.de Tel +49 37292 709778 Mobil: 0172 8790 741