I assume a pendulum or escapement is out? at least
better than a
synchronous motor i would think.
how about a tuning fork? very much like a crystal, just a matter of scale
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
On Mon, Nov 16, 2026 at 9:26 AM Anders Nelson via cctalk
<cctalk(a)classiccmp.org> wrote:
Hmm I think it's going to be difficult to make a clock signal without at
least 1 tube or transistor . Maybe use a motor and cam to periodically
close a contact? If You use a synchronous AC motor, you should get very
close to some fraction of 50/60Hz.
--
Anders Nelson
On Mon, Nov 16, 2026, 10:21 AM Holm Tiffe via cctalk <cctalk(a)classiccmp.org>
wrote:
> The goal is to use diodes, resistors, capacitors and coils
> (transformer, Relais for reset purposes), nothing more, at least no
> active devices like thermoionic tubes, transistors or ICs.
>
> The url from the linked video was buggy, I've wrote uhr2.mp4 instead of
> Uhr2.mp4 ..corrected this, now both file names should work.
>
> Regards,
> Holm
>
> Anders Nelson via cctalk wrote:
>
> > My first thought was to use a 555 timer as well, but I think the ask was
> to
> > use no ICs. In any case, all digital logic was first created without ICs.
> >
> > --
> > Anders Nelson
> >
> > On Mon, Nov 16, 2026, 10:12 AM <bitwiz(a)12bitsbest.com> wrote:
> >
> > > Is there any reason you can't either use a 555 or use a higher
> frequency
> > > crystal and decade counters to divide or a small micro with a
> programable
> > > timer (pico, nxp, altera, etc.)
> > >
> > > On Nov 16, 2026 8:21 AM, Anders Nelson via cctalk <
> cctalk(a)classiccmp.org>
> > > wrote:
> > >
> > > Can you use decatrons? Each will divide by a power of ten.
> > >
> > > --
> > > Anders Nelson
> > >
> > >
> > >
> > > On Mon, Nov 16, 2026, 8:43 AM Will Cooke via cctalk <
> cctalk(a)classiccmp.org>
> > >
> > > wrote:
> > >
> > > >
> > > >
> > > > > On 11/16/2026 8:08 AM EST Holm Tiffe via cctalk <
> cctalk(a)classiccmp.org>
> > >
> > > > wrote:
> > > > >
> > > > >
> > > > > Hi all,
> > > > ...
> > > > >
> > > > > So here my question: Has anyone an xtal with an very low
frequency
> > > laying
> > > > > around, which frequency can be devided down to 1 Hz (with ring
> > > counters,
> > > > > flipflops etc)? Maybe 1 oder 2Khz? ..or some other frequency
that
> is
> > > > > "dividable" to 1Hz?
> > > > > Shouldn't be for nothing and I'm paying for the shipping
(to
> germany).
> > > > >
> > > > > This is not the last stand, but it can demonstrate what I'm
doing:
> > > > >
> > > > >
https://www.tiffe.de/images/uhr2.mp4
> > > > >
> > > > > Thx in advance,
> > > > > Holm
> > > > > --
> > > >
> > > >
> > > > Hi,
> > > > That's a really cool project. You obviously have more patience
than
> I.
> > > I
> > > > would like to see the final result.
> > > >
> > > > I've personally never seen a crystal lower than 10 KHz. I
didn't
> know
> > > > such a thing existed. However, have you considered making your
> own? I
> > > > have heard of that being done and have wanted to try it, but I
> haven't
> > > > gotten around to it yet. In theory it should be relatively easy.
> Take
> > > a
> > > > chunk of quartz, cut it into a rectangle, and attach electrodes.
> Grind
> > > on
> > > > sandpaper and a flat surface until you get the right frequency. Of
> > > course,
> > > > once you cut the crystal you can only raise the frequency.
"Crystal
> > > > grinding" to raise the frequency used to be a common practice.
I am
> not
> > > > sure about starting from scratch. I have seen very little of that.
> But
> > > it
> > > > might be worth trying if you the project hasn't already used up
all
> your
> > > > patience!
> > > >
> > > > Good luck!
> > > > Will
> > > >
> > >
> > >
> > >
>
> --
> Technik Service u. Handel Tiffe,
www.tsht.de, Holm Tiffe,
> Goethestrasse 15, 09569 Oederan, USt-Id: DE253710583
> info(a)tsht.de Tel +49 37292 709778 Mobil: 0172 8790 741
>
>