12 Jun
2024
12 Jun
'24
9:21 p.m.
Hopefully I can find someone who has a manual for this qbus board, if
not, does anyone have experience with this board?
Summary:
It's a dual width qbus board with 1 DLV11-J port, 32KW Boot room, on
board LTC circuit and has a 16 pin connector to attach to a front
panel. I dumped the prom's and you can see them over on the VCF
Forum/DEC page. I used PDP11GUI to probe the I/O space and it looks
similar to a MXV11-B boot board, with the addition of a serial port, LTC
and front panel control. The board has copyright 1986 so it's not that
old.
I guess a front panel would have; LED for RUN, LED for DC OK, a switch
for HALT, switch for RESTART and possibly a switch to disable LTC. The
board has a couple of 4N25 optocouplers and what signals would need
isolation?
Yes, I would like to use this put together a working qbus PDP11 using
either 11/23 or 11/73 CPU, just for fun.
Doug
13 Jun
13 Jun
8:04 a.m.
-----Original Message-----
From: Douglas Taylor via cctalk <cctalk(a)classiccmp.org>
Sent: Wednesday, June 12, 2024 10:22 PM
To: General Discussion: On-Topic and Off-Topic Posts <cctalk(a)classiccmp.org>
Cc: Douglas Taylor <dj.taylor4(a)comcast.net>
Subject: [cctalk] Dilog Multifunction MQ-100 board
Hopefully I can find someone who has a manual for this qbus board, if not, does
anyone have experience with this board?
Summary:
It's a dual width qbus board with 1 DLV11-J port, 32KW Boot room, on board
LTC circuit and has a 16 pin connector to attach to a front panel. I dumped the
prom's and you can see them over on the VCF Forum/DEC page. I used
PDP11GUI to probe the I/O space and it looks similar to a MXV11-B boot board,
with the addition of a serial port, LTC and front panel control. The board has
copyright 1986 so it's not that old.
I guess a front panel would have; LED for RUN, LED for DC OK, a switch for
HALT, switch for RESTART and possibly a switch to disable LTC. The board has a
couple of 4N25 optocouplers and what signals would need isolation?
Its common to use OPTO couplers on current loop interfaces, so perhaps the DLV11-J type
port but with current loop.
Yes, I would like to use this put together a working qbus PDP11 using either
11/23 or 11/73 CPU, just for fun.
Doug
Dave
4:25 p.m.
On 6/13/2024 4:04 AM, Dave Wade G4UGM via cctalk wrote:
I was able to trace the optocoupler LED pins (1 and 2) to the gnd (pin
2) and pin 1 and 2 of the front panel connector (pins 1), both going
thru a 4.7K ohm resistor. I am beginning to suspect that these connect
to a lighted switch for HALT and RESTART. I have to see where the
collector of the optocouplers connect to before being certain.
Doug
-----Original
Message-----
From: Douglas Taylor via cctalk <cctalk(a)classiccmp.org>
Sent: Wednesday, June 12, 2024 10:22 PM
To: General Discussion: On-Topic and Off-Topic Posts <cctalk(a)classiccmp.org>
Cc: Douglas Taylor <dj.taylor4(a)comcast.net>
Subject: [cctalk] Dilog Multifunction MQ-100 board
Hopefully I can find someone who has a manual for this qbus board, if not, does
anyone have experience with this board?
Summary:
It's a dual width qbus board with 1 DLV11-J port, 32KW Boot room, on board
LTC circuit and has a 16 pin connector to attach to a front panel. I dumped the
prom's and you can see them over on the VCF Forum/DEC page. I used
PDP11GUI to probe the I/O space and it looks similar to a MXV11-B boot board,
with the addition of a serial port, LTC and front panel control. The board has
copyright 1986 so it's not that old.
I guess a front panel would have; LED for RUN, LED for DC OK, a switch for
HALT, switch for RESTART and possibly a switch to disable LTC. The board has a
couple of 4N25 optocouplers and what signals would need isolation?
Its common to
use OPTO couplers on current loop interfaces, so perhaps the DLV11-J type port but with
current loop.
Yes, I would like to use this put together a
working qbus PDP11 using either
11/23 or 11/73 CPU, just for fun.
Doug
Dave
163
days inactive
164
days old
2 comments
2 participants
participants (2)
-
dave.g4ugm＠gmail.com -
Douglas Taylor