[cctalk] Re: DECnet-RT on OpenSIMH

I have been able to bring up the DECnet-RT images, that Jay posted a few weeks ago, on OpenSIMH. Below are my notes on how to get it running. John. Notes for getting DECnet-RT V2.1 running on OpenSIMH NOTE: DECnet-RT is a phase III system so it does not understand Phase IV areas and can only address nodes in the range 1 - 255. If you attach it so a Phase IV router (e.g. PyDECnet) it can be accessed as node nnn in the area that the router is in. If you are bringing it up as part of a larger network (e.g. HECnet) make sure you "own" it's address otherwise you may cause routing problems. I have tried running DECnet on most versions of RT-11 from 5.0 to 5.7. Any version after 5.4D has various problems with file/terminal I/O. The available images will only run on an unmapped system with background/foreground support. This means that everything; monitor, disk driver, DECnet and application must fit in 28KW. Later versions of RT-11 slighly increased the size of the monitor and/or disk drtiver so that NFT and FAL will not fit in memory. DECnet-RT requires features that are not provided in the distributed monitors so you will have to generate a new monitor (See RT-11 System Generation Guide). You can take all of the default answers except: "Do you want the single job monitor?" Answer N "Do you want device time-out support?" Answer Y "How many extra device slots do you want?" Answer 4 Once you are running the new monitor, copy all the files from the 3 RX50 floppy images (RX0808.IMG, RX0809.IMG and RX0810.IMG) to your system device: COPY/SYS DUx:*.* SY: The system is configured to use a DLV-11 (CSR 176500, vector 300, priority 5) for network access. Add the following lines to your OpenSIMH .ini file: SET CPU 11/23 SET DLI ENA LINES=1 SET DLO0 DATASET 8B ATTACH DLI LINE=0,SPEED=115200,CONNECT=<IP ADDR>:<PORT>;NOTELNET If you are attaching to PyDECDnet, the associated configuration line would be: circuit dl-0 DDCMP --mode tcp --local-port <PORT> where <IP ADDR> and <PORT> need to be set according to your network. The network configuration is in a file called "CETAB.MAC". We can use CFE (Configuration File Editor) to change the node name and address (in this case to node name RT11 at address 111): .R CFE File name <SY:CETAB.MAC>: CFE>LIST EXEC Executor permanent characteristics as of 00:00 Identification = ERC PDP-11/23 Name = ERC23, Address = 124 Host = 124, Maximum links = 4 CFE>DEFINE EXECUTOR NAME RT11 ADDRESS 111 HOST 111 IDENT "RT11 11/23" CFE>LIST EXEC Executor permanent characteristics as of 00:01 Identification = RT11 11/23 Name = RT11, Address = 111 Host = 111, Maximum links = 4 CFE>DEFINE NODE 112 NAME REMOTE CFE>EXIT The last DEFINE command defines nodes in your DECnet network so you can connect to them. To load DECnet: .ASSIGN SY NT .R NCP NCP>SET SYSTEM NCP>SET EXECUTOR STATE ON NCP>SHO EXEC Node volatile summary as of 00:00 Executor node = 111 (RT11) State = On, Identification = RT11 11/23 NCP>EXIT If you want to allow incoming connections run NJS (Network Job Spawner): .R NJS ?NJS-I-Network Job Spawner Active and then it will report each program activation. The following programs are available: NCP - Network Control Program NFT - Network File Transfer TLK - Interactive talk with another (remote) terminal RMT - Remote terminal (RSX) RVT - Remote terminal (VMS) CED - Dumps internal DECnet data structures (/AL dumps everything) The following servers are available: NML - Network Management Listener (use with NCP) FAL - File Access Listener (use with NFT) LOOPER - Loop testing (use with NCP LOOP NODE name)